Dell H965N, K789N, K788N, K806N, 500W, H914N, H900N manual Typical Alarms and Conditions, Event Log Menu

Page 60

Event Log Menu

From the Event Log menu, you can access the last 50 events, which includes events, notices, and alarms, arranged from newest to oldest.

Events are silent conditions that are recorded in the Event Log as status information, such as “Clock Set Done.” Events do not require a response.

Notices and alarms are records of when events occurred and, if applicable, when they were cleared.

SNotices, including active notices, are recorded in the Event Log. Active notices, such as “UPS on Battery,” are announced by an intermittent beep. Notices do not normally require a response.

SAlarms, including active alarms, are recorded in the Event Log. Active alarms are announced by an intermittent beep. Examples are “Output Overload” and “Heatsink Overtemperature.” Active alarms require a response.

The Main Status Menu displays by default. To access troubleshooting information using the Event Log menu:

1Press the button for one second to go to the main menu selection and scroll down to the Event Log menu using the button.

2Click the button to enter the Event Log list.

3Scroll through the listed events, notices, and alarms using the or button.

Typical Alarms and Conditions

Table 16 describes typical alarms and conditions.

Table 16. Typical Alarms and Conditions

Alarm or Condition

Possible Cause

Action

 

 

 

The UPS does not provide or

The batteries need charging or

Apply utility power for 48 hours to charge the

indicate the expected backup

service.

batteries. If the condition persists, contact

time.

 

 

 

your service representative.

 

 

 

Power is not available at the

The UPS is in Standby mode.

Supply power to the connected equipment by

UPS output receptacles.

 

pressing the On/Off button until the front

 

 

 

 

panel displays the UPS status summary screen.

 

 

 

The UPS does not start. (The

Power is not connected.

Check the power cord connections. Also

LCD is off.)

 

ensure that the battery is plugged in.

 

 

 

The UPS operates normally,

The equipment is not

Verify that the equipment is plugged into the

but some or all of the

connected correctly to the UPS.

UPS receptacles. Also verify that the load

protected equipment is not

 

segment is on.

on.

 

 

 

 

 

 

 

 

 

60

Troubleshooting

 

 

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Users Guide September 2009 S 164201786 Table of Contents RS-232 and USB Communication Ports Network Transient Protector Dell UPS Management SoftwareTesting Batteries UPS Status Menu Event Log MenuIntroduction Dell Tower UPSIntroduction Finding Information What are You Looking For? Find It HereSafety Warnings UPS Output PowerSafety Warnings Installation Inspecting the EquipmentUnpacking the System Unpacking the SystemIdentifying the UPS Rear Panels 100/120V Rear Panel120V Rear Panel 120V, 1500W/100V Rear Panel Identifying the UPS Front Panel Connecting the UPS Internal Battery Removing the UPS Front CoverConnect the internal battery connector see Figure External Battery Module Installation Removing the Battery Connector CoverInstalling the Battery Connector Cover Installing the UPS Typical UPS Installation 120V Model ShownMinimum Upstream Circuit Breaker Rating UPS Output Power Power Cord RatingsUPS Initial Startup Rating Australia Optional GB2099 to C13 Connecting the Power Cord Installation Operation UPS Startup and ShutdownStarting the UPS Starting the UPS on Battery UPS ShutdownControl Panel Functions Control Button Functions Control Button SequenceChanging the Language Display FunctionsStartup Screen Screen Locked UPS StatusBattery Mode Bad Battery Detected or Battery DisconnectedUPS General Alarms Active Battery Test StatusStatus Summary Screens Description Normal Mode Standby ModeBattery Status Screens Description Event Log MeasurementsControl Screens Control Screens DescriptionSettings Settings Description Available Settings Default SettingIdentification Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Retrieving the Event Log Behavior on OverloadConfiguring Load Segments Controlling Load Segments Through the DisplayConfiguring Automatic Start Delay Configuring Automatic on Battery Shutdown Configuring Battery Settings Configuring the UPS for an EBMConfiguring Automatic Restart Running Automatic Battery TestsConfiguring Automatic Battery Tests Additional UPS Features RS-232 and USB Communication PortsRS-232 Communication Port Pin Assignment GNDDell Network Management Card Optional Dell Network Management CardNetwork Transient Protector Dell UPS Management SoftwareUPS Maintenance UPS and Battery CareTransporting the UPS Disconnect the internal battery connector see Figure When to Replace Batteries Testing BatteriesStoring the UPS and Batteries Updating the UPS Firmware Specifications Efficiency Normal mode Electrical Output 100/120V Models 230V Models Power LevelsElectrical Input Nominal VoltageEnvironmental and Safety Operating TemperatureTemperature Relative Humidity Safety ConformanceBattery Configuration Battery RuntimesVoltage FusesTroubleshooting Accessing Alarms and ConditionsUPS Status Menu Typical Alarms and Conditions Event Log MenuAction Troubleshooting Silencing the Alarm
Related manuals
Manual 63 pages 12.26 Kb

J716N, 500W, H965N, H900N, J715N specifications

Dell's power supply units (PSUs) are essential components for Dell servers and workstations, providing reliable power solutions tailored to meet different demands. Among these, the 500W, 1000W, and 1920W/1500W power supplies stand out for their efficiency, performance, and advanced features tailored to various IT environments.

Starting with the 500W power supply, this unit is designed for entry-level servers and workstations. It boasts a compact design that facilitates easy installation in space-constrained scenarios. The 500W PSU operates with a high efficiency rating, contributing to lower energy costs and reduced heat output. It supports the latest energy standards, including 80 PLUS certification, ensuring that customers can rely on it for consistent performance and reliability. This unit is particularly suitable for small to medium businesses looking for cost-effective power solutions for basic applications.

The 1000W power supply represents a step up, featuring dual 12V outputs that provide stable power for more demanding tasks. Designed for mid-range servers and advanced workstations, it balances performance and efficiency, making it ideal for enterprises that require additional processing power for virtualization, data analysis, and high-performance computing tasks. The 1000W PSU includes built-in protections against over-voltage, short circuits, and over-temperature conditions, adding an extra layer of reliability that is crucial for mission-critical operations.

For environments with higher power demands, Dell offers the 1920W/1500W power supply. This robust unit is engineered for high-performance servers and large-scale data centers, where maximum uptime and performance are paramount. The modular design of the 1920W/1500W power supply allows for enhanced cable management, reducing clutter and improving airflow within racks. With an efficiency rating that adheres to 80 PLUS Platinum standards, this PSU not only minimizes energy consumption but also maximizes operational efficiency, making it ideal for organizations looking to optimize their data center environments.

In summary, Dell's 500W, 1000W, and 1920W/1500W power supplies cater to a wide range of computing needs. From entry-level solutions to high-capacity units for demanding environments, Dell ensures that its power supplies provide reliability, efficiency, and performance. As organizations continue to evolve their IT infrastructure, these power supplies remain pivotal in supporting their growth and operational goals.
Top Page Image Contents