Phase Technology PC-3.0, V-3.0 manual Input and Left Input and should be, Brackets

STAND OFF BUMPER,

LOCK NUT, WASHER

WALL MOUNT BRACKETS

CENTER INPUT

RIGHT INPUT LEFT INPUT

FLAT PANEL WALL MOUNT

ATTACHMENT INSERTS

8 3/16”

USE THESE SETS OF HOLES

FOR SPEAKER BRACKETS FOR

NORMAL WALL MOUNTING

FIGURE 1

least 2 holes on each bracket that line up over a wall stud. Drill the wall and install your anchors and fasten the brackets to the wall with the “J” bend at the bottom (fig. 2 & 3).

Step 3

Place your TEATRO sound bar speaker face down on a soft clean surface with the grille on. Orient the speaker so the input terminal is on the left hand side. The second pair of steel brackets supplied with the speaker is designed to attach to the threaded inserts on the rear of the speaker cabinet with the 8 supplied #10-32x3/8” Philips screws. Simply align the holes on the brackets with the center and bottom set of mounting holes on the rear of the speaker. Position the brackets similar to the ones mounted on the wall with the “J” bend up so it can hook into the wall bracket. Attach brackets to the rear of the speaker using 4 screws per bracket (fig. 1 & 2).

Install one each of the 6, #10-32x1” Phillips screws in the threaded nut located in the bottom center of the “J” bend of the two wall mounted brackets. These screws are for leveling the speaker. Just start the screws but do not screw in at this time.

Install the other 4, 1” screws in the end mounted nuts of the cabinet mounted brackets. These are the bracket locking screws and should be install so they can be adjusted from the bottom of the speaker (fig. 3).

Assemble the 2 rubber stand-off bumpers next. Thread one nut onto each bumper stand-off and then one nylon washer. Run the nut about half way down the screw. Thread each of the bumper stand-offs into the 2 lower inserts located on the bottom rear edge of the cabinet.

Step 4
There is 3 pair of gold binding post terminals	FIGURE 2
on the rear of the speaker cabinet. The
	SPEAKER MOUNTING BRACKETS HOOK
terminals are marked for Right Input, Center
	INTO WALL MOUNTING BRACKETS
Input and Left Input and should be
connected to the respective speaker channel
outputs on your receiver. Connect the
speaker wires to the correct terminals
observing the polarity indicated on the	Figure 1
terminal. Red is + or positive and black is – or
negative. Strip about ½” of insulation from the
wires and separate the wires as necessary. If	SPEAKER MOUNT
you are using other wire lugs or connectors,	BRACKETS
attach them at this time to the bare wire.
Unscrew the binding post terminals and slip
the stripped end of the wire through the hole
in the metal post. Secure the wire in the post
by tightening the binding post terminal nut
down on the bare wire or lug. Make sure the
nut is tight and the wire will not pull out of the
terminal by lightly pulling back on the wire.
Tuck the speaker wire in behind the speaker
cabinet and if necessary or neaten up the
wire with the use of tie wraps.

Step 5

The TEATRO sound bar speaker is now ready to be mounted to the brackets that were screwed to the wall in step 2. The brackets are made to interlock with each other. Raise the speaker so the brackets on the rear of the cabinet are aligned with the wall brackets and engage the “J” bends in the

two sets of brackets together. If the speaker is being installed very close to the bottom of the flat panel display the speaker brackets can be slid into each other from the side. After the brackets are interlocked, it is a simple matter to center the speaker by sliding it side to side. The speaker can also be leveled by turning in the appropriate height adjusting screw to raise and lower the ends of the speaker. This is done with a #2 Phillips screwdriver from the bottom side of the bracket. Once the speaker position is trimmed up it should be locked in place using the 4 locking screws in the speaker bracket (fig. 3). Be carful not to over tighten the screws.