American Power Conversion 1609 Function Factory User Selectable Description Default Choices

Page 8

 

 

 

 

User Configurable Items

 

 

 

 

Function

Factory

User Selectable

Description

Default

Choices

 

 

 

 

 

 

 

Low Battery

2 minutes

2, 5, 8, 11, 14,

 

PowerChute software interface provides

Warning

 

17, 20, 23 minutes

automatic, unattended shutdown when

 

 

 

 

approximately two minutes of battery operated

 

 

 

 

run time remains.

 

 

 

 

The low-battery warning beeps are continuous

 

 

 

 

when two minutes of run time remain.

 

 

 

 

Change the low battery warning interval setting

 

 

 

 

to the time that the operating system or system

 

 

 

 

software requires to safely shut down.

 

 

 

 

 

Synchronized

0 seconds

• 0 s

• 240 s

Specify the time the UPS will wait after the

Turn-on Delay

 

• 60 s

• 300 s

return of utility power before start up (to avoid

 

 

• 120 s

• 360 s

branch circuit overload).

 

 

• 180 s

• 420 s

 

 

 

 

 

 

High Transfer Point

120 V models:

 

 

To avoid unnecessary use of the battery where

 

127 VAC

• 127 VAC

• 133 VAC

utility voltage is chronically high, set the high

 

 

• 130 VAC

• 136 VAC

transfer point higher if the connected

 

 

equipment can tolerate this condition.

 

230 V models:

 

 

 

 

 

 

 

253 VAC

• 253 VAC

• 261 VAC

 

 

 

• 257 VAC

• 265 VAC

 

 

 

 

 

 

Low Transfer Point

120 V models:

 

 

To avoid unnecessary use of the battery where

 

106 VAC

• 97 VAC

• 103 VAC

utility voltage is chronically low, set the low

 

 

• 100 VAC

• 106 VAC

transfer point lower if the connected equipment

 

 

can tolerate this condition.

 

230 V models:

 

 

 

 

 

The 1609-U500E ships ready for 230 V

 

208 VAC

• 196 VAC

• 204 VAC

 

sources. When operating the UPS in 208 V

 

 

• 200 VAC

• 208 VAC

 

 

applications, the UPS low transfer voltage

 

 

 

 

 

 

 

 

settings are adjusted through PowerChute

 

 

 

 

software or the Network Management Card.

 

 

 

 

The proper setting for low transfer voltage is

 

 

 

 

196 V.

 

 

 

 

Refer to the PowerChute user guide or the

 

 

 

 

Network Management Card instructions for

 

 

 

 

setting adjustment details.

 

 

 

 

 

Output Voltage

 

 

 

230 V models only: Sets the output voltage of

230 V models

230 VAC

• 220 VAC

• 240 VAC

the UPS while operating on battery.

 

 

• 230 VAC

 

 

 

 

 

 

 

9

Image 8
Contents Industrial Uninterruptible Power Supply Battery Installation Mount the UPSConnect Power and Equipment to the UPS Front PanelConnectors Parameter ValueDisplay Panel Indicators and Function Buttons Indicator Indicator Title DescriptionOperation UPS Display PanelFeature Feature Title Function Button Battery ChargeUser Configurable Items UPS settingsFunction Factory User Selectable Description Default Choices Storage Storage, Maintenance, TransportReplacing the Battery Module Troubleshooting Problem and/or Possible Cause SolutionAVR Boost or AVR Trim LEDs are illuminated Replace Battery/Battery Disconnected LED is illuminatedInput circuit breaker trips There is no utility power UPS operates on battery although line voltage existsBattery Charge and Load LEDs flash simultaneously Diagnostic utility voltageContact Rockwell Automation Service and Contact InformationService Safety Information Save this Guide Replacement and Recycling of Batteries