SET UP and Troubleshooting

potential for induced system noise.

Step 4 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding themselves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 5 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

Step 7 Disconnect the vehicle's battery ground terminal.

Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM).

Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate performance of your Orion Cobalt amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions.

Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA con- nections are completed.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System section of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in the voiding of your warranty and possible damage to the amplifier.

Testing the System

After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion Cobalt system.

Step 1 Check all the wiring connections to be sure they are correct and secure.

Step 2 Turn the signal source volume control all the way down. Set any tone controls to their flat or defeated positions. This includes the loudness control.

Step 3 Turn the level controls of the amplifier to their minimum positions.

Step 4 Turn the source unit on. Check to see if the power LED located on the input side of the amplifier is on. If not, please refer to the Power Connections and the Troubleshooting Tips sections of this manual for instructions.

Step 5 If using an aftermarket source unit, turn the level controls of the amplifier about one quarter of a turn. Slowly increase the volume level of the source unit to so that you can hear the output of the system. If no sound is heard or if the output is dis- torted, turn the system off immediately. Refer to the Power Connections and the Troubleshooting Tips sections of this manual to solve your installation problems.

Step 6 Check to make sure the output for each channel is correct. If the active crossovers are used, check to make sure that each output is correct from the amplifier. When using active crossovers on midrange and tweeters, do not use crossover frequen- cies lower than recommended. If the system is not configured properly, refer to

CO6004 specifications

The Orion Car Audio CO6004 is a renowned component speaker system designed for audiophiles seeking a high-quality sound experience in their vehicles. This system is known for its powerful performance, impressive sound clarity, and a range of advanced features that set it apart in the competitive car audio market.

At the heart of the CO6004 is a pair of robust 6.5-inch woofers. These speakers are crafted with a high-strength polypropylene cone, providing durability and resilience against harsh environmental conditions while delivering deep, thumping bass. The woofers are designed to produce a broad frequency range, allowing users to enjoy both bass-heavy tracks and crisp vocal performances with equal clarity.

Complementing the woofers are 1-inch silk dome tweeters that excel in producing high-frequency sounds. These tweeters are specially designed to create a smooth, natural sound without distortion. With a frequency response that spans from 45Hz to 24kHz, the CO6004 ensures that every note is delivered accurately, from the deepest bass lines to the highest treble.

One of the standout features of the Orion CO6004 is its built-in crossover network. This technology allows for seamless transition between the woofers and tweeters, ensuring that each speaker operates within its optimal frequency range. The result is a well-balanced sound stage that enhances the overall listening experience. Additionally, the system includes adjustable tweeter level controls, allowing users to customize the audio output to their personal preferences.

Installation of the CO6004 is made easy with its user-friendly design. The speakers come with a range of mounting options and hardware, ensuring compatibility with various vehicle models. The compact size of the components also facilitates straightforward placement without taking up excessive space.

Durability is another hallmark of the Orion Car Audio CO6004. The speakers are built with weather-resistant materials, making them suitable for use in different climates and under various driving conditions. This resilience ensures longevity and consistent performance over time.

In summary, the Orion Car Audio CO6004 stands out as a premier choice for car audio enthusiasts. With its powerful woofers, precision tweeters, advanced crossover technology, and durable design, it delivers an exceptional audio experience that enhances any drive. Whether for casual listening or serious sound quality appreciation, the CO6004 proves to be a worthy investment for improving your vehicle's audio system.