Trunk Compartment

ing possible. When mounting your amplifier under a seat or similar area, keep a minimum of 1" of clearance around the amplifier for adequate cooling.

Mounting your amplifier in the trunk provides excellent performance as long as you do not restrict the airflow around the heatsink of the amplifier. For optimal results, mount the amplifier with as much clearance as possible. This type of mounting will yield the best cooling due to the convection effect of the amplifier chassis.

General Precautions and Installation Tips

WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle.

Disconnect the vehicle's ground wire at the battery before making or breaking connections to the audio system's power supply terminals.

Do not use this amplifier unmounted. Failing to securely mount the amplifier can result in damage or injury, particularly in the event of an accident. An unmounted amplifier becomes a dangerous projectile in the event of a crash. Never mount the amplifier where it might get wet. Mount the amplifier so the wire connections will not be pulled. Route the wires where they will not be scraped, pinched or damaged in any fashion.

The +12V power supply wire must be fused as close as possible to the battery terminal, ideally within 18". Use the recommended fuse size or circuit breaker listed in the Power Connections section of this manual.

If you need to replace the fuse plugged into the side of the amplifier, replace the fuse with the same size ATC / MAXI type fuse that came with the amplifier. If you are not sure as to the correct value, refer to the Power Connections section of this manual for details. Using a higher current fuse may result in damage to the amplifier that is not covered under warranty.

NOTE: Make sure all the equipment in the system is turned off when making or breaking con- nections to the input RCAs or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections.

Power for systems with a single amplifier can be supplied by most automotive electrical systems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly recommend the use of a Directed Audio Essentials power capaci- tor with an extra battery in larger stereo systems.

Orion Cobalt amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air circulation. Remember, beach blankets, last week's laundry, school books and homework papers located on top of the amplifier do not improve air flow and may become damaged.

Step By Step Installation

Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information.

Step 2 Decide on the system configuration for your amplifier. For system suggestions, refer to the Speaker Connections section of this guide.

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and bat- tery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great

8	© 2008 directed electronics—all rights reserved

CO6004 specifications

The Orion Car Audio CO6004 is a renowned component speaker system designed for audiophiles seeking a high-quality sound experience in their vehicles. This system is known for its powerful performance, impressive sound clarity, and a range of advanced features that set it apart in the competitive car audio market.

At the heart of the CO6004 is a pair of robust 6.5-inch woofers. These speakers are crafted with a high-strength polypropylene cone, providing durability and resilience against harsh environmental conditions while delivering deep, thumping bass. The woofers are designed to produce a broad frequency range, allowing users to enjoy both bass-heavy tracks and crisp vocal performances with equal clarity.

Complementing the woofers are 1-inch silk dome tweeters that excel in producing high-frequency sounds. These tweeters are specially designed to create a smooth, natural sound without distortion. With a frequency response that spans from 45Hz to 24kHz, the CO6004 ensures that every note is delivered accurately, from the deepest bass lines to the highest treble.

One of the standout features of the Orion CO6004 is its built-in crossover network. This technology allows for seamless transition between the woofers and tweeters, ensuring that each speaker operates within its optimal frequency range. The result is a well-balanced sound stage that enhances the overall listening experience. Additionally, the system includes adjustable tweeter level controls, allowing users to customize the audio output to their personal preferences.

Installation of the CO6004 is made easy with its user-friendly design. The speakers come with a range of mounting options and hardware, ensuring compatibility with various vehicle models. The compact size of the components also facilitates straightforward placement without taking up excessive space.

Durability is another hallmark of the Orion Car Audio CO6004. The speakers are built with weather-resistant materials, making them suitable for use in different climates and under various driving conditions. This resilience ensures longevity and consistent performance over time.

In summary, the Orion Car Audio CO6004 stands out as a premier choice for car audio enthusiasts. With its powerful woofers, precision tweeters, advanced crossover technology, and durable design, it delivers an exceptional audio experience that enhances any drive. Whether for casual listening or serious sound quality appreciation, the CO6004 proves to be a worthy investment for improving your vehicle's audio system.