Monitor Audio GS FX owner manual Your Gold GS LCR, Wrms

Page 5

Your Gold GS LCR

A centre speaker is often required to produce over 60% of the entire sound output and, therefore, must be able to faithfully reproduce explosions and sound effects as well as it does clear, tonally accurate dialogue. The outstanding dynamic reach and generous power handling of the GS LCR means that it can cope with the most demanding inputs and always have something in reserve. New design ideas have been employed to optimise accuracy, control and dispersion over a wide listening area. And it has the exact tonal signature and balance to integrate “invisibly” with any of the speakers in the Gold Signature range.

The GS LCR has been designed to work just as well as a main left/ right speaker as it is as a centre speaker. Because of this, if it is being used vertically, please ensure the cabinet badge is always on the right. By doing this means that the low frequencies go

to the bottom bass unit and the mid frequencies go to the top bass unit.

To remove the grille, carefully prize it away from the cabinet using you fingers. The main grille locates in the elongated holes around the outside of the driver chassis. To replace it, line the peg fixings (in the grille) up with the elongated holes and gently press into place.

For system set up please see positioning ideas on pages 7 and 8.

 

 

 

 

 

 

 

Maximum

 

Power

 

Recommended

 

Bass

Frequency

Sensitivity

 

Nominal

 

 

 

 

Amplifier

 

Response

(1W@1m)

 

Impedance

S.P.L (Per pair in

Handling

 

power output.

 

Alignment

 

 

 

 

(ohms)

 

room). dBA

 

RMS (W)

 

 

(W)RMS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

40Hz –

 

89dB

 

8

 

 

110

 

150

 

 

40 – 150

 

Sealed

43kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

Enclosure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tweeter

 

Bass

 

 

 

 

 

External

 

External

 

 

 

 

Drive Unit

Dimensions -

 

 

crossover

 

Crossover

 

 

Dimensions -

Weight Kg (lb)

frequency

 

Frequency

 

Complement

Excluding plinth

 

Including plinth

kHz

 

Hz

 

 

 

 

 

W x H x D

 

mm (inch)

 

 

 

 

 

 

 

mm (inch)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 x 6” RST®2

 

 

 

 

 

 

 

2.7

 

 

 

 

 

 

Bass/

 

 

 

 

 

 

 

 

N/A

 

mid-range driver

 

206 x 560

 

N/A

12.5 / (27.5)

 

 

 

 

 

 

1 x 25mm Gold

 

x 230

 

 

 

 

 

 

 

 

 

 

 

Dome

 

(8 1/8” x

 

 

 

 

 

 

 

 

 

 

 

C-CAM®

 

22 1/16”x

 

 

 

 

 

 

 

 

 

 

 

tweeter.

 

9 1/16”)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

© Monitor Audio Ltd 2005

 

 

V2

Image 5
Contents GS FX & GS LCR Contents Introduction Read Instructions CleaningWater & Moisture HeatWrms Your Gold GS LCR106 Your Gold GS FXSetting up the GS FX Optimum Performance Volt Trigger Monopole/ Dipole Switch Front Panel SwitchesLocation Switch Positioning System Example large System Example small Page Fixing Your GS FX to a Wall Connecting Your Gold GS Loudspeakers Customer Service Guarantee and ServiceClaims under this Guarantee Dealer Details Data ProtectionOwner Information Moisten Here England