Brady 200M-e 300 manual Media and Ribbon Sensor Sensitivity Press NEXT/SAVE to

Page 61

Press

Display Shows

 

Action/Explanation

 

 

Media and Ribbon Sensor Sensitivity: Press NEXT/SAVE to

 

 

skip the calibration procedure and continue with the host port

 

 

selection parameters that follow. Press the (+) key to start the

 

MEDIA AND

calibration procedure.

 

RIBBON

This procedure is used to adjust the sensitivity of the media and

 

CALIBRATE

ribbon sensors.

 

 

NOTE: The procedure must be followed exactly as presented.

 

 

 

All steps must be performed even if only one of the

 

 

 

sensors requires adjustment.

 

 

 

Media and Ribbon Calibration Procedure

 

 

 

 

 

 

1)

Open the printhead.

 

 

2)

Remove approximately 8" (203 mm) of labels from the media

 

LOAD BACKING

 

roll, enough so that only the backing material is threaded

 

 

 

between the media sensors when the media is loaded.

 

 

3)

Close the printhead.

 

 

NOTE: If you want to cancel the operation, press the (–) key.

 

 

 

 

 

 

1)

Open the printhead.

 

 

2)

Remove the ribbon (sliding it as far to the right as possible has

 

REMOVE RIBBON

 

the same effect as removing it).

 

 

3)

Close the printhead.

 

 

NOTE: If you want to cancel the operation, press the (–) key.

 

 

 

 

 

The printer automatically adjusts the scale (gain) of the signals it

 

CALIBRATING

receives from the media and ribbon sensors based on the specific

—

PLEASE WAIT

media and ribbon combination you are using. On the sensor

 

 

profile, this essentially corresponds to moving the graph up or

 

 

down to optimize the readings for your application.

 

 

 

 

 

When “RELOAD ALL” is displayed:

 

 

1)

Open the printhead and pull the media forward until a label is

—

RELOAD ALL

 

positioned under the media sensor.

 

 

2)

Move the ribbon back to its proper position.

 

 

3)

Close the printhead.

 

 

 

 

 

Now that the scale has changed, the printer performs another

 

 

calibration. During this process, the printer checks the readings

 

MEDIA AND

for the media and ribbon based on the new scale you have

 

RIBBON

established, determines the label length, and determines whether

 

CALIBRATE

you are in direct thermal or thermal transfer print mode. The

 

 

process is now complete! To see the new readings on the new

 

 

scale, print a sensor profile.

 

 

 

 

Bradyprinter 200M-e and 200M-e 300 User’s Guide

51

Page 60 Page 62
Image 61
Page 60 Page 62
Contents @bà-ŠšÎkÂÔÌ11 Bradyprinter 200M-e and 200M-e 300 User’s Guide Bradyprinter 200M-e and 200M-e 300 User’s Guide Iii Bradyprinter 200M-e and 200M-e 300 User’s Guide +%5$&2 Bradyprinter 200M-e and 200M-e 300 User’s Guide 2AO’lÍŸyÍŸ›Ïl›ÏÆ ÆÏAO’‹Æˆ‹›€ÍŸ--Ø›‹YAÏ‹Ÿ› ³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³Ö ›c‹àÍÍÍ-ÍAÃc ³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³³çÑ Bradyprinter 200M-e and 200M-e 300 User’s Guide +HOOR ›ÏßcØYÏ‹Ÿ›8QSDFNLQJDQG,QVSHFWLRQ 5HSRUWLQJDPDJH6WRUDJH 0HGLDDQG5LEERQ5HTXLUHPHQWVFrqqhfwlrq 3RZHU&RUG3ULQWHU$QDWRP\ 3XUSRVH ’‹OÃAÏ‹›€ÍψlÍ-Ë›ÏlÃ1RQ&RQWLQXRXVHE0HGLD \SHVRI0HGLD1RQ&RQWLQXRXV%ODFN0DUN0HGLD RQWLQXRXV0HGLDKRRVLQJWKH3ULQW0RGH RDGLQJWKH0HGLD 7UDQVPLVVLYH6HQVRU 3RVLWLRQLQJWKH0HGLD6HQVRUV$GMXVWLQJWKH8SSHU0HGLD6HQVRU ODFN0DUN6HQVRU RDGLQJWKH5LEERQ URQW3DQHO 2SHUDWRU&RQWUROVRQILJXULQJWKH3ULQWHU Press Display Shows Action/Explanation RQILJXULQJWKH6RIWZDUHRU3ULQWHUULYHU0HGLDDQG5LEERQ&DOLEUDWLRQ Page 3ULQWLQJD7HVW/DEHO Bradyprinter 200M-e and 200M-e 300 User’s Guide \VWHP&RQVLGHUDWLRQV ÆÏAO’‹Æˆ‹›€ÍŸ--Ø›‹YAÏ‹Ÿ›Qwhuidfhv DWD6SHFLILFDWLRQVDEOLQJ5HTXLUHPHQWV ‹›ÏlÃÍAÆ‹YÆ URQW3DQHOLVSOD\ Key Function URQW3DQHO.H\VLight Status Indication URQW3DQHO/LJKWVCheck 7HDU2II0RGH 5ROO0HGLD/RDGLQJBefore closing the printhead, make sure 3HHO2II0RGHBradyprinter 200M-e and 200M-e 300 User’s Guide 5HZLQG0RGH Before closing the printhead, make sure XWWHU0RGH 3HHO2QO\0RGH Bradyprinter 200M-e and 200M-e 300 User’s Guide DQIROG0HGLD/RDGLQJ 5HPRYLQJWKH/DEHO%DFNLQJ0DWHULDO 5LEERQ/RDGLQJ Page 5LEERQ5HPRYDO Bradyprinter 200M-e and 200M-e 300 User’s Guide QWHULQJWKH6HWXS0RGH ›y‹€ØÃAÏ‹Ÿ›KDQJLQJ3DVVZRUG3URWHFWHG3DUDPHWHUV HDYLQJWKH6HWXS0RGH Default +10 Setting Print ParametersDefault +0 Default Tear-offSelections Web, mark Default WebPrint Width Listing Printer Information Initialize Card Initialize Memory CardYES ReadyInit Flash MEM Sensor Profile Media and Ribbon Sensor CalibrationMedia and Ribbon Sensor Sensitivity Press NEXT/SAVE to Media and Ribbon Calibration ProcedureSetting Serial Communications Press the + or key to Setting Communication ParametersDefault RS-232 DefaultDefault XON/XOFF Default EvenDefault None Network ID Setting Communications Mode Press the + or key toCommunications Control Prefix Selecting Prefix and Delimiter CharactersRange 00 FF Format PrefixDefault ZPL Selecting ZPL ModePower-Up Head Close Parameters Selections ZPL II, ZPLBackfeed Label Positioning ParametersLabel TOP Left PositionHead Resistor Default ValueMark S WEB S Media S Ribbon SMark MED S Media LED Ribbon LED Mark LEDFormat Convert LCD AdjustDefault All Default DynamicDefault Permanent Default EnglishSelecting the Display Language Press the + or key to LanguageThermal transfer print mode Direct thermal print modeŸØÏ‹›lÍAÃlÍA›cÍcØÆÏ-l›Ï OhdqlqjOHDQLQJWKH,QWHULRU OhdqlqjwkhwhulruOHDQLQJWKH3ULQWKHDGDQG3ODWHQ5ROOHU OHDQLQJWKH6HQVRUV OHDQLQJWKH6QDS3ODWH Page OHDQLQJWKH&XWWHU0RGXOH Xeulfdwlrq XVH5HSODFHPHQW7RJJOH3RVLWLRQLQJ $GMXVWPHQWV0HGLD6HQVRU3RVLWLRQ$GMXVWPHQW 3ULQWKHDG3UHVVXUH$GMXVWPHQW2ßØO’lƈŸŸÏ‹›€ Problem SolutionUURU&RQGLWLRQVDQGDUQLQJV UURU&RQGLWLRQ³+HDG2SHQ DUQLQJ³+HDG&ROG HQHUDO3ULQW4XDOLW\,VVXHV 3ULQW4XDOLW\3UREOHPVRppxqlfdwlrqv ULQNOHG5LEERQOdeho 3RZHU2Q6HOI7HVW 3ULQWHULDJQRVWLFV$GGLWLRQDO3ULQWHU6HOI7HVWV Cancel Key Self Test Pause Key Self Test Feed Key Self Test Feed Key and Pause Key Self Test Bradyprinter 200M-e and 200M-e 300 User’s Guide 0HGLD+DQGOLQJ 0lY‹y‹YAÏ‹Ÿ›Æ2SWLRQV DU&RGHV =HEUD3URJUDPPLQJ/DQJXDJH=3/,,ŠUPC/EAN LogmarsHQHUDO6SHFLILFDWLRQV General Specifications 200M-e/200M-eRibbon Specifications 200M-e/200M-e Printing Specifications 200M-e/200M-e3ULQWLQJ6SHFLILFDWLRQV 5LEERQ6SHFLILFDWLRQVRQW6SHFLILFDWLRQV SymbolOCR-B OCR-A0HGLD6SHFLILFDWLRQV Media Specifications 200M-e/200M-e3RZHU/LQH&RUG6SHFLILFDWLRQV Bradyprinter 200M-e and 200M-e 300 User’s Guide Warranty Information DUUDQW\FOXVLRQVDQG&RQGLWLRQV Printer Software and Firmware License Agreement ÃAc៛›lYÏÍ ‹Yl›Æl €Ãll-l›ÏRestrictions Bradyprinter 200M-e and 200M-e 300 User’s Guide Limitations and Release of Liability 3ULQWHU,QWHUIDFH7HFKQLFDO,QIRUPDWLRQ ›c‹àÍÍÍœÍÍŸ››lYÏŸÃÆDescription RS-232 Interface Connections Page RS-232 Interconnections Using a DB25 Cable RS-422/RS-485 Interconnections 3DUDOOHODWD3RUW Pin Connector Description$&DUG,QVWDOODWLRQ ›c‹àÍÍÍ-ÍAÃc104 Bradyprinter 200M-e and 200M-e 300 User’s Guide Bradyprinter 200M-e and 200M-e 300 User’s Guide 105 ›clà106 Bradyprinter 200M-e and 200M-e 300 User’s Guide Bradyprinter 200M-e and 200M-e 300 User’s Guide 107 108 Bradyprinter 200M-e and 200M-e 300 User’s Guide

200M-e, 200M-e 300 specifications

The Brady 200M-e and 300M-e series label printers represent the forefront of industrial labeling technology, designed to meet the demanding needs of various sectors including manufacturing, logistics, and healthcare. These printers are known for their exceptional durability, advanced features, and ease of use, making them ideal for professionals looking to enhance their labeling processes.

One of the defining characteristics of the Brady 200M-e and 300M-e series is their ability to produce high-quality labels quickly and efficiently. With a print resolution of up to 300 dpi, these printers deliver crisp, clear text and graphics that are essential for compliance and safety labeling. The fast printing speeds allow users to create labels in real-time, improving productivity and reducing downtime.

The series supports a wide range of materials including polyester, vinyl, and even heat-shrink tubing, allowing for versatile application in various environments. The printers can handle label widths up to 2 inches for the 200M-e and up to 4 inches for the 300M-e, catering to different labeling requirements. This flexibility ensures that users can create labels that are not only functional but also visually appealing.

Both models utilize advanced thermal transfer technology, which enhances the durability of the labels by making them resistant to chemicals, abrasion, and temperature changes. This feature is particularly valuable in industrial settings where labels are exposed to harsh conditions.

The Brady 200M-e and 300M-e series come equipped with an intuitive user interface, featuring a color touchscreen display that simplifies navigation and label design. Users can easily select from pre-designed templates or create custom labels using the built-in design software. Additionally, the printers support connecting to various data sources, enabling seamless integration with existing labeling workflows.

Another significant technology incorporated in these models is Wi-Fi and Bluetooth connectivity, allowing users to print from mobile devices and computers without being tethered to the printer. This wireless capability streamlines operations and adds convenience, making it easier to manage labeling tasks across large facilities.

In conclusion, the Brady 200M-e and 300M-e label printers are powerful solutions for anyone in need of robust and versatile labeling equipment. With their high-quality output, extensive material compatibility, user-friendly interfaces, and advanced connectivity options, they stand out as exceptional tools for enhancing workflow efficiency and compliance in industrial applications.
Top Page Image Contents