MK Sound VX-4, V-90, V-2B, V-1B Special Installation Notes, MX-2000, MX-100, MX-90, MX-80, V-100

Page 13

powered subwoofers

page 13

In some cases, however, you may prefer the subwoofer set to a higher playback level for video sources. This may occur when video sources (especially older films and some television) have very little deep bass present. You may also want to exaggerate the effect to make spectacular video sources even more impressive!

When your subwoofer is going to be located close to a television set, remember to leave 2 - 3 feet of clearance between the television and subwoofer, unless the subwoofer is magnetically shielded (V-125, MX-1000 and MX-1000cc only).

CONNECTING THE SUBWOOFER TO A SURROUND

SOUND RECEIVER OR PROCESSOR:

The preferred connection from a surround sound amp or controller is from a SUBWOOFER OUTPUT RCA jack. This connection usually insures that a full bass signal is fed to the subwoofer. If your component doesn't have a subwoofer output jack, connect the Subwoofer to the front Left and Right channel speaker outputs (don't use the Center channel).

VERY IMPORTANT: When the Subwoofer is connected to the Left and Right amplifier outputs (this means using speaker wires), and the controller is in Pro-Logic mode, the Center channel WIDE/ NORMAL switch MUST be set to the NORMAL mode. If the switch is set to the WIDE mode, the bass content of the Center channel will not be fed to the Subwoofer, and a significant amount of the bass in the material you are listening to will be lost.

10. SPECIAL INSTALLATION NOTES

MX-2000, MX-100, MX-90, MX-80, V-100, V-90:

An enclosed hardware kit contains four black metal spikes, threaded at one end and tapering to a sharp point at the other. Depending on their orientation, they can be used either as spikes or rubber feet. Do not use the spiked feet on hardwood or tile floors. They can damage the floor surface.

By mounting these spikes into the threaded inserts mounted in the bottom of the Subwoofer, you can elevate the Subwoofer, and on carpet, couple it more tightly to that floor. On hardwood, tile, or concrete, the spikes should be inverted, with the point mounted facing into the cabinet. One of the black rubber feet provided should then be pressed over the exposed flat end of the foot.

The threaded inserts are found in the four corners of the cabinet's bottom. The MX-2000 has a fifth insert, which allows you to use three of the five in a triangular pattern. The inserts are 1/4 - 20, that is, 1/4 inch in diameter and 20 threads per inch. This is compatible with the most spikes, "cones," "tip-toes," etc. offered by other manufacturers.

To properly secure the feet to the cabinet, you must use the provided washer and jamb nut on the threaded portion of the foot. The washer goes first, with the nut over it, holding the washer securely in place. This prevents damage to the spike and insert if something moves the cabinet sideways.

MX-100, MX-90, MX-80, MX-70:

Because your M&K MX-series Subwoofer uses an "inverted" driver that fires down into the floor, it loads differently to the room than a conventional speaker or forward-firing Subwoofer. This means that you may want to experiment a bit more with its placement and setup to get optimum sound quality.

1.Because of its downward-firing driver, your MX Subwoofer may be more susceptible to

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Series Table of Contents Powered subwooferspage Safety InstructionsIntroduction Where to Locate Your SubwooferSubwoofer HOOK-UP Standard AMPLIFIER/SPEAKER Wire Connections HIGH-LEVEL HIGH-PASS Filter Usage Satellite Speaker Wiring OptionAlso Shows USE of the V-125s HIGH-LEVEL HIGH-PASS Filter Using the Preamp Inputs RCA Jacks Wiring with a Separate AMP and Preamp RCA Jack InputsUsing AN M&K Electronic HIGH-PASS Filter Wiring with the LP-1S & VF-100 Electronic HIGH-PASS FiltersPlugging in the Subwoofer SATELLITE/SUBWOOFER Phasing TestUSE of the Filter Control Using TWO SubwoofersHome Theatre Usage FINE-TUNING Subwoofer PlacementMX-2000, MX-100, MX-90, MX-80, V-100 Special Installation NotesMX-70 TroubleshootingIf you hear a persistent hum or buzz through the Subwoofer Replacement Fuse Values If YOU Need Service

V-90, MX-70, MX-80, MX-1000, MX-2000 specifications

MK Sound is renowned for its high-performance audio products, consistently pushing the boundaries of sound technology. Among its acclaimed lineup are the VX-4, VX-7, V-1B, V-2B, and MX-100, each designed to deliver an extraordinary audio experience.

The MK Sound VX-4 is a compact yet powerful speaker that excels in various listening environments. It features a 4-inch woofer and a 1-inch tweeter, providing a broad frequency response that captures both the subtle details and the impactful lows of any audio track. The speaker’s design incorporates advanced construction techniques to minimize distortion, ensuring that every note is rendered with clarity. Its versatile mounting options make it suitable for both home and professional settings.

Moving up in the lineup, the VX-7 is designed for those who demand a bigger sound. With a larger 6.5-inch woofer and improved power handling capabilities, the VX-7 enhances the listening experience with rich bass and clear high frequencies. The speaker employs MK Sound's proprietary technology to achieve a seamless soundstage, making it ideal for multi-channel audio setups or stereo listening.

The V-1B and V-2B models are subwoofers that take low-frequency reproduction to the next level. The V-1B, featuring a 10-inch driver, is engineered to deliver punchy bass while maintaining precision. Its robust amplifier ensures powerful performance, perfect for home theater applications. The V-2B, with its dual 12-inch drivers, is designed for audiophiles seeking the ultimate bass experience. This subwoofer showcases extraordinary extension and dynamics, making it indispensable for cinema enthusiasts and music lovers alike.

Lastly, the MX-100 is MK Sound's flagship processor that brings sophisticated control to any audio system. It supports advanced audio formats and includes intuitive crossovers, ensuring seamless integration with all MK Sound speakers. The MX-100's customizable settings allow users to tailor their audio experience, maximizing both performance and enjoyment.

Overall, MK Sound’s VX-4, VX-7, V-1B, V-2B, and MX-100 embody cutting-edge technology and expert craftsmanship. Each product offers unique features designed for superior audio performance, ensuring that every listener experiences sound as it was meant to be heard. With MK Sound, quality and innovation remain at the forefront of audio reproduction.
Top Page Image Contents