MK Sound MX-70, VX-4, V-90, V-2B, V-1B SATELLITE/SUBWOOFER Phasing Test, Plugging in the Subwoofer

Page 10

powered subwoofers

page 10

PLUGGING IN THE SUBWOOFER

Once all the speaker wires or preamp interconnect cables are in place, you are ready to plug in the Subwoofer. Set the "BASS LEVEL" control to "MIN". Then plug the AC cord in. You should hear a thump from the Subwoofer. This is the normal sound of its power supply charging and discharging when it is plugged in and unplugged.

Once your system wiring is complete and the Subwoofer is plugged into the wall, leave it plugged in, even when the system is turned off. The normal mode of operation for the Subwoofer is to remain plugged in 24 hours a day. Among other things, this means that you don't have to walk over to the Subwoofer to turn it on every time you want to use the system.

If you decide to plug the Subwoofer into a switched outlet on another component, that outlet must have the following minimum power ratings:

Minimum of 150 watts: V-90, V-2B, V-3B, VX-4, VX-7

Minimum of 200 watts: MX-1000, MX-1000cc, MX-90, MX-80, MX-70, V-1B, V-125

Do not use a switched outlet with the MX-2000, MX-100, and V-100.

Now, play some music through your system to make sure that the Satellite speakers are working properly. If they are, carefully advance the "BASS LEVEL" control. The Subwoofer should begin to play. Set the "BASS LEVEL" control where the Subwoofer sounds in balance with the Satellite speakers. If the system is not working properly, unplug the Subwoofer and check all of your connections. Call your dealer or the factory if you cannot solve any problem.

The best way to set the level of the Subwoofer is to do it by ear, listening over several hours or days to familiar recordings. Make adjustments to the level in small increments, depending on whether the bass level sounds too high or too low. Of course, you can always deliberately set the level higher or lower than "flat" if you need a higher bass level or if you don't want to disturb your neighbors.

5. SATELLITE/SUBWOOFER PHASING TEST

SATELLITE/SUBWOOFER PHASING TEST

You are now almost finished with the basic set-up. But before you can sit down to enjoy your new Subwoofer, you need to perform one simple Phasing Test. This test insures optimum sound in the critical bass frequencies where your Subwoofer and Satellite speakers overlap.

NOTE: If you have the V-125subwoofer, ignore the instructions that make reference to changing the Satellite speaker inputs. In place of changing the inputs, all you have to do is move the "PHASE" switch on the V-125's back panel from either up (+) or down (—) to the opposite position.

Play a familiar CD, LP, or tape with steady, consistent bass. Listen carefully to the "mid-bass" (75 - 125 Hz) region — the part of the spectrum where electric or string basses and drums are found. Then, reverse the Positive and Negative speaker inputs on the back of BOTH Satellite speakers. Move the lead on the Positive (+) terminal to the Negative (—) terminal, and vice versa.

Alternately, you can do this at the Subwoofer's "TO SPEAKERS" terminals, but never switch the inputs at both the backs of the Satellite speakers and the Subwoofer.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Series Table of Contents Safety Instructions Powered subwooferspageIntroduction Where to Locate Your SubwooferSubwoofer HOOK-UP Standard AMPLIFIER/SPEAKER Wire Connections Satellite Speaker Wiring Option HIGH-LEVEL HIGH-PASS Filter UsageAlso Shows USE of the V-125s HIGH-LEVEL HIGH-PASS Filter Wiring with a Separate AMP and Preamp RCA Jack Inputs Using the Preamp Inputs RCA JacksWiring with the LP-1S & VF-100 Electronic HIGH-PASS Filters Using AN M&K Electronic HIGH-PASS FilterSATELLITE/SUBWOOFER Phasing Test Plugging in the SubwooferUsing TWO Subwoofers USE of the Filter ControlFINE-TUNING Subwoofer Placement Home Theatre UsageSpecial Installation Notes MX-2000, MX-100, MX-90, MX-80, V-100Troubleshooting MX-70If you hear a persistent hum or buzz through the Subwoofer If YOU Need Service Replacement Fuse Values

V-90, MX-70, MX-80, MX-1000, MX-2000 specifications

MK Sound is renowned for its high-performance audio products, consistently pushing the boundaries of sound technology. Among its acclaimed lineup are the VX-4, VX-7, V-1B, V-2B, and MX-100, each designed to deliver an extraordinary audio experience.

The MK Sound VX-4 is a compact yet powerful speaker that excels in various listening environments. It features a 4-inch woofer and a 1-inch tweeter, providing a broad frequency response that captures both the subtle details and the impactful lows of any audio track. The speaker’s design incorporates advanced construction techniques to minimize distortion, ensuring that every note is rendered with clarity. Its versatile mounting options make it suitable for both home and professional settings.

Moving up in the lineup, the VX-7 is designed for those who demand a bigger sound. With a larger 6.5-inch woofer and improved power handling capabilities, the VX-7 enhances the listening experience with rich bass and clear high frequencies. The speaker employs MK Sound's proprietary technology to achieve a seamless soundstage, making it ideal for multi-channel audio setups or stereo listening.

The V-1B and V-2B models are subwoofers that take low-frequency reproduction to the next level. The V-1B, featuring a 10-inch driver, is engineered to deliver punchy bass while maintaining precision. Its robust amplifier ensures powerful performance, perfect for home theater applications. The V-2B, with its dual 12-inch drivers, is designed for audiophiles seeking the ultimate bass experience. This subwoofer showcases extraordinary extension and dynamics, making it indispensable for cinema enthusiasts and music lovers alike.

Lastly, the MX-100 is MK Sound's flagship processor that brings sophisticated control to any audio system. It supports advanced audio formats and includes intuitive crossovers, ensuring seamless integration with all MK Sound speakers. The MX-100's customizable settings allow users to tailor their audio experience, maximizing both performance and enjoyment.

Overall, MK Sound’s VX-4, VX-7, V-1B, V-2B, and MX-100 embody cutting-edge technology and expert craftsmanship. Each product offers unique features designed for superior audio performance, ensuring that every listener experiences sound as it was meant to be heard. With MK Sound, quality and innovation remain at the forefront of audio reproduction.
Top Page Image Contents