MK Sound MX-5000THX Mk II, MX-350THX Testing the Subwoofer NON-THX, Using TWO Subwoofers NON-THX

Page 11

 

THX subwoofers

page 11

 

 

 

to feed these filters.

To connect one of these filters, run one set of shielded RCA - RCA interconnect cables from the receiver, amp or preamp's MAIN OUTPUT to the input jacks on the HP-80 or VF-80. Run another set of interconnects from the high frequency output jacks on the filter to receiver or amp's POWER AMP inputs. Last, run interconnects from the subwoofer output jacks to the subwoofer's "INPUT" jacks. See the instructions enclosed with your filter for wiring diagrams.

When using these filters,set the "BASS LEVEL" switch to "VARIABLE" and the "LOW PASS FILTER" switch to "80 Hz 24 dB/OCTAVE."

TESTING THE SUBWOOFER (NON-THX)

Once all of the interconnect cables are in place, you are ready to plug in your subwoofer. Make sure the "LOW PASS FILTER" switch is set to the "80 Hz 24 dB/OCTAVE" position and the "BASS LEVEL" control to set to "VARIABLE". Make sure the "PHASE" switch is set to the "+" position. Then plug the AC cord in. The red LED on the back panel of the subwoofer should illuminate.

When your system wiring is complete and the subwoofer is plugged into the wall, leave it plugged in, even when the system is turned off. The normal mode of operation for the subwoofer is to remain plugged in 24 hours a day. Among other things, this means that you don't have to walk over to the subwoofer to turn it on every time you want to use the system.

DO NOT PLUG THE SUBWOOFER INTO A SWITCHED OUTLET ON ANOTHER COMPONENT. THE SUBWOOFER CAN DRAW UP TO 700 WATTS FROM THE

AC LINE. IT MUST BE PLUGGED INTO A SOLID AC LINE.

Now, play some music through your system to make sure that the Satellite speakers are working properly. If they are, carefully advance the "BASS LEVEL" control. The subwoofer should begin to play. Set the "BASS LEVEL" control where the subwoofer sounds in balance with the Satellite speakers. If the system is not working properly, unplug the subwoofer and check all of your connections. Call your dealer or the factory if you cannot solve any problem.

SETTING THE SUBWOOFER LEVEL (NON-THX)

Here are two ways to set the subwoofer level. First, if you can obtain a spectrum analyzer, you can accurately match the subwoofer to the main speakers by feeding a wideband pink noise signal into the full system (both the satellites and the subwoofer). Set up the analyzer at the main listening position. Adjust the "BASS LEVEL" control until the analyzer display shows the flattest response through the 70 to 125 Hz midbass region.

If you don't have access to an analyzer, the best way to match the level of the subwoofer to your system is to do it by ear, listening over several hours to familiar recordings. Make adjustments to the level in small increments, depending on whether the bass level sounds too high or too low.

There is a possibility that your surround sound processor has a built in test generator for the subwoofer level, but most non-THX processors do not. If you do have such a surround sound processor, see SETTING SUBWOOFER LEVEL (THX), on page 7.

In any case, remember that you can always deliberately set the level higher if you want more bass or lower if you don't want to disturb your neighbors or family.

USING TWO SUBWOOFERS (NON-THX)

Using two subwoofers in your audio/video system will give you the ultimate in bass performance. It will give you improved impact and definition, as well as greater output and dynamic range. If you locate the subwoofers in different parts of the room, you will hear a better overall frequency response, as the room modes excited by one woofer are complemented by the presence of the other. Alternately, if you stack two subwoofers, one on top of the other, their outputs will couple and give you

Page 10 Page 12
Image 11
Page 10 Page 12
Contents THXpowered subwoofers Wiring Diagrams Table of ContentsTHX subwooferspage Safety InstructionsOperation with THX Components Where to Place Your SubwooferConnecting the Subwoofer to a THX Controller IntroductionWiring ONE Subwoofer with a THX Controller Operation of the Bass EQ Switch THX Testing the Subwoofer THX ModeOperation of the LOW Pass Filter Switch THX Operation of the Bass Level Switch THXOperation with a NON-THX Processor Setting Subwoofer Level THXUsing TWO Subwoofers THX Operation of the LOW Pass Filter SwitchWiring with a NON-THX Processor or Preamp Operation of the Bass EQ SwitchOperation of the Bass Level Switch Use a Y-connector To connect to Two subwoofers Wiring with the M&K HP-80 or VF-80 HIGH-PASS Filters NON-THX Using TWO Subwoofers NON-THX Testing the Subwoofer NON-THXSetting the Subwoofer Level NON-THX Phasing Test Method TWO SATELLITE/SUBWOOFER Phasing TestSpecial Note if YOU have a THX 5.1 Channel Processor Phasing Test Method ONESpecial Method for Placing the Subwoofer FINE-TUNING the Placement of Your SubwooferIf your subwoofer has no output TroubleshootingUSE of Spiked Feet If YOU Need to Replace the External Fuse If you hear a persistent hum or buzz through the subwooferVolt SpecificationsCabinet Maintenance Replacement Fuse Values

MX-350THX, MX-5000THX Mk II, MX-350THX specifications

MK Sound is a renowned name in the world of high-performance audio, and their lineup, particularly the MK-5000THX Mk II and MX-350THX, showcases their commitment to innovation, precision, and immersive sound experiences. The MX-5000THX Mk II is a powerful subwoofer designed to deliver deep, rich bass that enhances any audio system, making it an ideal choice for both home theater enthusiasts and audiophiles.

Featuring advanced technology, the MX-5000THX Mk II utilizes a high-excursion 15-inch driver that creates an impressive low-frequency response down to 20 Hz. This subwoofer is THX certified, ensuring it meets rigorous standards for performance and reliability. The design approach of the MX-5000THX Mk II incorporates a dual-firing configuration, allowing it to produce a more balanced and immersive soundstage. Its robust amplifier provides 500 watts of continuous power, with dynamic peaks allowing it to deliver visceral audio that can be felt as much as heard.

In contrast, the MX-350THX is a more compact yet equally formidable subwoofer option. Its smaller 12-inch driver does not compromise performance, delivering an impressive low-end response ideal for smaller rooms or systems where space is a premium. Like its larger sibling, the MX-350THX also boasts THX certification, reflecting its ability to reproduce cinematic sound with accuracy and impact. The subwoofer is engineered with a down-firing design that aids in better integration with room acoustics, providing a smoother overall bass response.

Another standout feature across these models is the flexibility in setup options, with multiple input configurations that support various audio sources, including high-level and low-level inputs. This versatility allows users to seamlessly integrate these subwoofers into their existing home theater or music systems.

In terms of aesthetics, both the MX-5000THX Mk II and MX-350THX are designed with clean lines and a modern look, ensuring they can fit seamlessly into any room decor. With robust build quality, these units are built to withstand the rigors of home use while delivering consistent performance.

In summary, MK Sound’s MX-5000THX Mk II and MX-350THX deliver exceptional quality and performance for both casual listeners and serious audio enthusiasts. With advanced technologies, THX certification, and versatile setup options, these subwoofers represent a significant investment in sound quality, elevating any audio experience to new heights.
Top Page Image Contents