MK Sound MX-350THX operation manual SATELLITE/SUBWOOFER Phasing Test, Phasing Test Method ONE

Page 12

THX subwoofers

page 12

 

 

an additional total of 6 dB of output.

Wiring with two subwoofers is simple. Instead of running two interconnect cables to one subwoofer, just run one interconnect to each subwoofer, using the "LEFT/MONO INPUT" jack on each subwoofer. You don't need a Y-connector. See Figure 4 (page 9), or Figure 6 (page 10).

7. SATELLITE/SUBWOOFER PHASING TEST

(WITH BOTH THX AND NON-THX COMPONENTS)

Before you can sit down to enjoy your new subwoofer, you need to perform one simple Phasing Test. This test insures optimum sound in the critical bass frequencies where your subwoofer and Satellite or L/C/R speakers overlap. There are two methods of tessting, which are listed below.

When using the subwoofer with a THX controller and THX L/C/R speakers, or with M&K Satellite speakers and an HP-80 High-Pass Filter, the crossover slopes are linear phase. When the subwoofer is placed along the same axis as the front speakers, the system will tolerate a plus or minus 28 inch offset before significant losses at the crossover point are seen.

SPECIAL NOTE IF YOU HAVE A THX 5.1 CHANNEL PROCESSOR

Your THX 5.1 channel processor or receiver has a feature that allows you to electronically "move" the position of the main speakers so that the signal from each speaker arrives at your ear at the same time. It does this by time delaying the signal that is fed to the speakers that are closer to your ears. In order to properly set the phase of the subwoofer, you must set the time delay of the main and/or surround speakers first. Any time you change the amount of time delay to the other speakers, it can affect the phase relationship between those speakers and the subwoofer.

PHASING TEST METHOD ONE

Set the switch labelled "PHASE" to the "+" position. Then, play a familiar CD, LP, laserdisc or tape with steady, consistent bass content. Listen carefully to the "mid-bass" region of 70 - 125 Hz. This is the part of the spectrum where electric or string basses and drums predominate.

Then, reverse the position of the "PHASE" switch. If it is set to the "+" position, set it to the "-" position. If it was set to the "-" position, set it to the "+" position. The best way is to have a partner work the switch while you sit in the main listening position and listen.

Now listen to the same music, concentrating on the mid-bass. If you hear less bass, set the "PHASE" switch to the opposite position. If you hear more bass, leave the switch where it is; the new position is correct.

PHASING TEST METHOD TWO

First, set the toggle switch labelled "PHASE" to the "+" position. Then, feed wideband pink noise (found on test CDs, the THX "Wow" disc, or a pink noise generator) through your front channel speakers and your subwoofer. You can do this test by listening, but it is best to use a spectrum analyzer and look at its display in the "mid-bass" region of 70 - 125 Hz.

Then, reverse the position of the "PHASE" switch. If it is set to the "+" position, set it to the "-" position. If it was set to the "-" position, set it to the "+" position. The best way is to have a partner work the switch while you sit in the main listening position and listen.

Now, listen to the same wideband pink noise or look at the spectrum analyzer output in the mid- bass region. If you hear/measure less bass, set the "PHASE" switch to the opposite position. If you hear/measure more bass, leave the switch alone; the new position is correct.

This test is necessary because the different distances from each speaker to your ears mean that it is possible that the Subwoofer's output may arrive at your ears out of phase with the Satellites'

Page 11 Page 13
Image 12
Page 11 Page 13
Contents THXpowered subwoofers Table of Contents Wiring DiagramsSafety Instructions THX subwooferspageWhere to Place Your Subwoofer Connecting the Subwoofer to a THX ControllerIntroduction Operation with THX ComponentsWiring ONE Subwoofer with a THX Controller Testing the Subwoofer THX Mode Operation of the LOW Pass Filter Switch THXOperation of the Bass Level Switch THX Operation of the Bass EQ Switch THXSetting Subwoofer Level THX Using TWO Subwoofers THXOperation of the LOW Pass Filter Switch Operation with a NON-THX ProcessorOperation of the Bass EQ Switch Operation of the Bass Level SwitchWiring with a NON-THX Processor or Preamp Use a Y-connector To connect to Two subwoofers Wiring with the M&K HP-80 or VF-80 HIGH-PASS Filters NON-THX Testing the Subwoofer NON-THX Setting the Subwoofer Level NON-THXUsing TWO Subwoofers NON-THX SATELLITE/SUBWOOFER Phasing Test Special Note if YOU have a THX 5.1 Channel ProcessorPhasing Test Method ONE Phasing Test Method TWOFINE-TUNING the Placement of Your Subwoofer Special Method for Placing the SubwooferTroubleshooting USE of Spiked FeetIf your subwoofer has no output If you hear a persistent hum or buzz through the subwoofer If YOU Need to Replace the External FuseSpecifications Cabinet MaintenanceReplacement Fuse Values Volt

MX-350THX, MX-5000THX Mk II, MX-350THX specifications

MK Sound is a renowned name in the world of high-performance audio, and their lineup, particularly the MK-5000THX Mk II and MX-350THX, showcases their commitment to innovation, precision, and immersive sound experiences. The MX-5000THX Mk II is a powerful subwoofer designed to deliver deep, rich bass that enhances any audio system, making it an ideal choice for both home theater enthusiasts and audiophiles.

Featuring advanced technology, the MX-5000THX Mk II utilizes a high-excursion 15-inch driver that creates an impressive low-frequency response down to 20 Hz. This subwoofer is THX certified, ensuring it meets rigorous standards for performance and reliability. The design approach of the MX-5000THX Mk II incorporates a dual-firing configuration, allowing it to produce a more balanced and immersive soundstage. Its robust amplifier provides 500 watts of continuous power, with dynamic peaks allowing it to deliver visceral audio that can be felt as much as heard.

In contrast, the MX-350THX is a more compact yet equally formidable subwoofer option. Its smaller 12-inch driver does not compromise performance, delivering an impressive low-end response ideal for smaller rooms or systems where space is a premium. Like its larger sibling, the MX-350THX also boasts THX certification, reflecting its ability to reproduce cinematic sound with accuracy and impact. The subwoofer is engineered with a down-firing design that aids in better integration with room acoustics, providing a smoother overall bass response.

Another standout feature across these models is the flexibility in setup options, with multiple input configurations that support various audio sources, including high-level and low-level inputs. This versatility allows users to seamlessly integrate these subwoofers into their existing home theater or music systems.

In terms of aesthetics, both the MX-5000THX Mk II and MX-350THX are designed with clean lines and a modern look, ensuring they can fit seamlessly into any room decor. With robust build quality, these units are built to withstand the rigors of home use while delivering consistent performance.

In summary, MK Sound’s MX-5000THX Mk II and MX-350THX deliver exceptional quality and performance for both casual listeners and serious audio enthusiasts. With advanced technologies, THX certification, and versatile setup options, these subwoofers represent a significant investment in sound quality, elevating any audio experience to new heights.
Top Page Image Contents