Basic operations, Turning the power on and off

Turning the power on and off (Continued)

Notes

•The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p.39 .

•The first time you use the projector after purchase, after the start-up screen disappears, the start menu is displayed p.27 .

•Beep sound can be set not to beep in the Default setting 1 menu p.42 .

•When [Key lock] is [On], the operation buttons of the projector do not work p.43 .

•When [Password setting] is [On], then the start-up screen is displayed after the Password entry screen disappears p.33 .

Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning the power on” p.25 .

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, the start menu for lan- guage (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)

■ Turning the power off

1 Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears.)

2Press the ON/STANDBY button once again.

When the setting of beep sound is [On], the projector beeps, and the screen turns off, but the internal cooling fan continues to operate. Then, the projector goes into standby mode.

qUse theorbutton to select the desired language and press thebutton.

Message for setup confirmation is displayed in a selected language.

Then, the menu for lamp power selection and configuration is displayed. It is automatically set as Standard. To change the setting, follow the step w.

wUse theor button to select the lamp power and press the button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Polish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

During cooling, the ON/STANDBY indicator flashes. While the indicator is flashing, the power can not be turned back on. At this point of time, it does not matter even if you unplug the power cord.

Note

•The projector consumes about 10W of power in standby. We recommend that you unplug the power cord if you will not be using the projector for an extended period.

PRECAUTION

•If you turn the power on before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.

LCD Panels

LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the following precautions.

•In order to extend the lifetime of the LCD panel, always turn off the power when not in use, and make sure that the lamp is off. Keeping the lamp off is also very effective at saving electricity.

•If the air filter becomes dirty and clogged, the projector’s internal temperature will rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter from time to time p.52 , and replace it periodically. Contact the store where you purchased your projector, or your local Service Station for replacement air filters.

Notes

•When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting 2 menu p.43 , the start menu will be displayed the next time when the power is turned on.

•The language can also be set via the Display setting menu p.39 and Lamp power via the Default setting 1 menu p.42 .

•This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals.

Notes

•When [Auto input search] is set to [Off] in the Default setting 1 menu p.42 (factory setting is [On]), the Input select menu appears if you press the INPUT button.

•If no signal is being output from the connected equipment, pressing the INPUT button does not change the input and “There is no other input signal.” will appear.

Operations