Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning the power on” p.24 .

5Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot adjuster.

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, the start menu for lan- guage (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)

qLift up the front of the projector to the desired angle, then press the foot adjuster release button.

The foot adjuster extends. Release the button to lock the position.

w To fine adjust the angle, twist the

q Use the or button to select the

English

foot adjuster.

desired language and press the	button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.

wUse the or button to select the lamp power and press the button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Polish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

eTo adjust the horizontal angle, use the right and left tilt adjusters.

•To stow the foot adjuster, hold up the projec- tor while pressing the foot adjuster release button, then slowly lower the projector.

6Adjusting the screen size and focus

qUse the zooming lever to adjust the screen size.

wUse the focusing ring to adjust the focus.

Notes

•When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting menu p.40 , the start menu will be displayed the next time when the power is turned on.

•The language can also be set via the Display setting menu p.37 and Lamp power via the Default setting menu p.40 .

•This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals.

Notes

•When [Auto input search] is set to [Off] in the Default setting menu p.40 (factory setting is [On]), the Switch input menu appears if you press the INPUT button p.40 .

•If no signal is being output from the connected equipment, pressing the INPUT button does not change the input and “There is no other input signal.” will appear.

7Adjusting the volume with the buttons

The speaker volume can be adjusted when an audio signal is being input.

Notes

•Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.

•A lamp is consumable item. If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on conditions of use.)

•The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions.

•Although this projector supports a wide range of RGB signals p.50 , any resolutions not supported by this projector (XGA) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer’s external output should be set to XGA resolution.

•With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor’s display may prevent the images from displaying properly. If this happens, turn off the computer’s LCD display. For information on how to turn off the LCD display, see the owner’s manual of your computer.

•If no signal is being input from the connected equipment or signal input is stopped while projecting, the “No signal” will appear.

•If a signal not supported by the projector is input, the “Unsupport signal” will appear.

•If an unavailable operation button is pressed, the icon will appear.

Toshiba TDP-T95 owner manual Basic operations