Toshiba TLP-X20U Lamp replacement, Pull out the lamp, Lamp cover, Handle to pull out the lamp

Page 86

Lamp replacement

CONTENTS

86

The lamp will eventually begin to project dark or dull pictures and finally will not light up. (Lamp’s life length depends on the use condition.) In such a case, replace the lamp with new one.

CAUTION

•If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning or replacement of the lamp.

•When replacing, always use lamp “TLPLX10” (sold separately). For detail, refer to the lamp instruction.

•If you have been using the projector, the lamp will be very hot, and may cause burn injuries. Wait for the lamp to cool (for longer than 1 hour) before replacing it.

•If the lamp should break, please handle with care to avoid injury due to broken pieces and contact your dealer for repair service.

1 Unplug the power cord.

2 Wait until the lamp gets cold enough.

3

Take off the lamp cover on the

bottom panel.

Loosen two screws, and pull off the lamp cover.

1

Lamp cover

2

4

 

Pull out the lamp.

1

Loosen the two fixing screws, and lift up the

 

 

handle to pull out the lamp.

 

 

2

Maintenance

Continued

Page 85 Page 87
Image 86
Page 85 Page 87
Contents TLP-X10U TLP-X11U TLP-X20U TLP-X21U Before useSafety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Ventilation Power SourcesSource of Light Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedReplacement Parts Important Safety InstructionsDamage Requiring Service ServicingDo not move the projector while the arm is still erect Safety CheckDo not carry by the camera arm Strong light may cause damage to your eyes or sightPower supply cord selection Contents Names of each part on the main unit Selection button Menu buttonUse Names of each part on the remote control Open the cover Install the batteriesLoading batteries Attach the coverRemote control operation BeforeFloor-mounted projector placement ViewerSide view Determine the screen size projected on the screenTop view Light Orange Connect the power cordTake off the lens cover Insert the other end in a wall outletTurn clockwise to lift up Turn counterclockwise to lower Projector placement angle adjustmentFoot adjuster Ceiling-mounted projector placement Installation and connectionConnecting a computer Connecting a computer with DVI output connector Computer in 2 Connector DVI connectorConnecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Press ON/STANDBY Playback modeProjection on the screen Turn on the connected equipment and put itSignal sent from the computer Select the input sourcePress VOL/ADJ +/ to adjust volume Adjust the picture size by turningFocusing ring Zooming leverPress ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Adjusting the picture automatically Press Auto SETCorrecting the keystone distortion Press Auto KeystonePress Mute Remote controlCutting off the picture and sound temporarily OperationsPress Freeze Icon Appears in the freeze modeFreezing the picture Picture freezesPress Resize Icon Appears in the resize modeEnlarging the picture size Sub-picture is displayed Displaying PIP Sub-picturesPress PIP Information described below is displayed Displaying InformationPress Call Pressed againOperating a computer by the remote control Projecting images stored in a memory card About memory cardsInsert the memory card into the card slot Press Input repeatedly to select the memory card inputUse VOL/ADJ +/ to change pages. Remote control Control panelDescription of screen ChangingPress Exit Press ENTER. Slide displayPress VOL/ADJ +/-. Slide transition Projecting images stored in a memory card To eject the memory cardAdjustments and settings on the menu screen Quick MenuAdjustments and settings on the menu screen Operating the menu screen StartPress Menu Quick Menu adjustments and settingsYou can set the basic setting used frequently Quick Menu appearsTypes of adjustment and setting items are different See the table belowLamp power Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Auto. demo Memory card inputPress VOL/ADJ +/- to select the type of input source Sub-menu screen of input source setting appearsPress Enter Press Exit to return to the Quick MenuUse the selection buttons / to select a language Menu screen disappears Sub-menu screen of interval setting appearsUse the selection buttons / to select interval time Press Menu twice Full Menu adjustments and settings -PictureAdjustments Full Menu adjustments and settings Picture Screen size Picture mode RGB inputInput select mode Memory card input Slide show Memory card inputPress Exit to return to the Full Menu Sub-menu of selected items appears PositionLevelVideo mode Video input, S-video input Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Sub-menu of selected items appearsFull Menu adjustments and settings Picture Full Menu settings Audio Channel select After the settings are finished, press ExitSpeaker output LoudnessUse the selection buttons To display Keystone menu Full Menu settings KeystoneUse the selection buttons To select Setting items Press Exit several times until the menu screen After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter DisappearsWhen pressed once, the Quick Menu screen appears. When Full Menu settings DisplayUse the selection buttons To select Setting items Settings Use the selection buttons To display Display menuWhen selecting Language in step Menu background translucent No signal background Setting of screen of no signal inputMenu position Start-up screenWhen pressed once, the Quick Menu screen appears. When Full Menu settings Default settingUse the selection buttons To display Default setting menu Sub-menu of Input source setting appears Control panel Main unit sideRear ceiling Ceiling-mounted rear projection Use the selection buttons / to select the projection modeSub-menu of Projection mode appears Press VOL/ADJ +/ to set No signal power offPower on Picture menus for the each input to Full Menu settings Factory reset modeFactory default setting Full Menu settings Factory reset mode Audio Set the audio input source PIP menu settingSize Set the PIP sub-picture size Menu screen disappearsArm Camera lens LED light Camera control panel Lights when the white balance is lockedTo adjust the camera gain To store camera images into the memory cardPreparation of the document imaging camera Set a document to be projected Setting directionPress ARM Light Images on the screenPress Camera to select the camera input mode Move the camera head to adjust the size PictureFollow the steps of Preparation of the document imaging Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Camera in reverseProject a white paper and enlarge it to fill Balance Press W.BALANCE to turn the Lock indicatorLock the white balance ScreenCover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothStore the camera images into the memory card Power turns off or does not come on IndicatorPower does not come on Trouble indicationsClean the air filter Air filter cleaningUnplug the power cord Take off the air filter coverMount the air filter cover Air filter cleaningAssemble the air filter Air filter Filter frame Air filter coverCleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterLamp cover Lamp replacementPull out the lamp Loosen two screws, and pull off the lamp coverAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover in place and tighten two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Mini D-sub 15pin Connector Do not connect anythingTiming chart Applicable signalSignal Timing Horizontal Signal Timing Vertical Applicable signal Compatible video signalControlling the projector by using RS-232C Mini DIN 8-pinControlling the projector by using RS-232C AS1 MB1 VLU Auto SET USB output Type B SpecificationsMini DIN 8-pin RS-232C Specifications Replacement lampEnclosed. All transportation and insurance charges must be Prepaid by youLimited Warranty

TLP-X10U, TLP-X20U, TLP-X11U, TLP-X11, TLP-X20 specifications

Toshiba has made a significant mark in the world of projection technology, with models such as the TLP-X21U, TLP-X20, TLP-X11, TLP-X11U, and TLP-X20U. Each of these projectors showcases impressive features tailored for both professional and educational environments.

The TLP-X21U is renowned for its high brightness of 3000 ANSI lumens, making it perfect for large rooms or well-lit environments. It offers a native XGA resolution of 1024 x 768, ensuring clarity and detail in presentations. This model also supports a wide range of inputs, including HDMI and VGA, enhancing versatility for various devices. Additionally, its lamp life can reach up to 2000 hours in eco mode, allowing for longer use between replacements.

The TLP-X20 takes features further with enhanced brightness and connectivity. With 3200 ANSI lumens, it is ideally suited for settings where light management is challenging. It boasts a similar native XGA resolution but adds the ability to project in a variety of formats, including widescreen. Advanced color technology ensures vibrant and accurate color reproduction, crucial for dynamic presentations.

Moving onto the TLP-X11 and TLP-X11U, these models are designed for portability and ease of use. Both projectors weigh less, making them ideal for users who require mobility without sacrificing quality. The TLP-X11U offers a wide range of inputs, similar to its higher-end counterparts, but with slightly lower brightness of 2500 ANSI lumens. Nonetheless, it retains a strong focus on clear and engaging visuals with XGA resolution.

The TLP-X20U stands out with its unique combination of high brightness level and energy efficiency. With 3000 ANSI lumens and an extended lamp life, it serves as a robust option for those who need reliable performance over prolonged periods. Its ease of installation and user-friendly interface makes it accessible for individuals with varying levels of technical expertise.

In summary, the Toshiba TLP series delivers an array of powerful projection solutions. Whether for classroom settings or corporate presentations, models like the TLP-X21U, TLP-X20, TLP-X11, TLP-X11U, and TLP-X20U embody versatility, clarity, and reliability. Toshiba’s commitment to fostering an interactive experience makes these projectors suitable for various applications, ensuring that users can communicate their ideas effectively with engaging imagery and exceptional performance.
Top Page Image Contents