MartinLogan 1000 user manual Multi-Channel/LFE Mode, Set the crossover switch to Bypass LFE

Page 9

Multi-Channel/LFE Mode

This setup is recommended if your Dynamo 1000 will be used in a dedicated home theater or multi-channel system. When a signal is connected to the subwoofer’s LFE input, and the crossover switch is set to 'Bypass (LFE In)' the internal low pass filter is not active. By following this setup, you will allow your processor to handle most of the bass management.

If you will be using your system for both 2-channel and multi-channel listening we recommend using this setup and connection method. Some modern receivers and processors allow users to route left and right channel low-frequency information, in addition to discrete LFE infor- mation, through the LFE output.

Signal Connection (see figure 4):

1Connect the LFE output of the processor to the LFE input using a quality RCA interconnect.

WARNING!

Based on the performance of most proces- sors, it is recommended that MartinLogan center and effects type speakers (i.e. Motif, Matinee, Stage, etc.) not be run in large, wide, or full range mode. Doing so may potentially damage the speaker if the proces- sor attempts to drive the speaker beyond its rated frequency range. This warning also applies to products from other manufacturers.

It is recommended to run center and effects type speakers in limited or narrow mode. Some processors have an option to route the LFE channel to your main and/or surround speakers. We recommend that you do not use this option.

Recommended Control Settings (see figure 5):

1Set the crossover switch to 'Bypass (LFE In)'.

2Use the bass management section of your processor‘s speaker level setup option to set the subwoofer level at an appropriate level. Follow the instructions in your processor manual to fine-tune the subwoofer level.

3If your processor offers the option to setup crossovers for a subwoofer, we recommend that you start with the following settings—Crossover: 70Hz, High-Pass: 12dB, and Low-

Pass: 24dB. The optimal setting for these options may vary depending on your room and listening preferences.

4Adjust the phase control until ideal blending is obtained. If you hear no discernible difference leave the phase at 0°.

5Follow the instructions in your processor manual to fine- tune the subwoofer level

Figure 4. Signal connection for multi-channel mode.

Figure 5. Control settings for multi-channel mode.

Connections and Control Settings 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents TmD y n a m o tm Important Safety Instructions Contents Packaging Introduction Signal Connection Installation in BriefUnpacking Listen and EnjoyAbout the Controls Before Connecting the Dynamo Connections and Control SettingsChannel Mode Signal Connection see figureSet the crossover switch to Bypass LFE Multi-Channel/LFE ModeOptional Wireless Connection AC Power ConnectionReplacing the Fuse Break-InInstalling in a Cabinet PlacementListening Position Ask Your DealerChanging Woofer Orientation Your Room Room AcousticsTerminology Solid FootingFront Left and Front Right Home TheaterCenter Channel Surround SpeakersFrequently Asked Questions & Troubleshooting Frequently Asked QuestionsTroubleshooting Warranty and Registration SpecificationsService General InformationDimensional Drawings Glossary of Audio Terms Glossary of Audio Terms Rev. #072409

1000 specifications

The MartinLogan 1000 is a remarkable achievement in the realm of high-end audio speakers, showcasing the perfect blend of cutting-edge technology and exquisite craftsmanship. At the core of the 1000's design is the innovative electrostatic transducer that provides an unparalleled listening experience. This technology allows for a rapid response and a wide frequency range, capturing subtle nuances in music that other speakers may miss.

One of the standout features of the MartinLogan 1000 is its electrostatic panel, which uses a thin, flexible diaphragm placed between two electrically charged plates. This design ensures minimal distortion, resulting in sound reproduction that is more accurate and true to the original recording. The speaker's ability to create an expansive soundstage is another defining characteristic, allowing listeners to perceive depth and detail that is often lost in conventional dynamic speakers.

In addition to the electrostatic technology, the MartinLogan 1000 incorporates advanced imaging and dispersion techniques. The speakers are designed to deliver precise sound localization, allowing listeners to easily pinpoint individual instruments and vocals within a mix. This is particularly beneficial for audiophiles who seek an immersive listening experience akin to that of attending a live performance.

The cabinet of the MartinLogan 1000 is crafted with a strong emphasis on aesthetics and function. Constructed from high-quality materials, it boasts a sleek and modern appearance that fits seamlessly into any home environment. The use of premium wood veneers enhances its visual appeal while also contributing to the structural integrity of the speaker.

Connectivity is another strong suit of the MartinLogan 1000. The speaker is designed to integrate effortlessly with a variety of audio systems, featuring multiple input options to accommodate all types of setups. This versatility ensures that users can maximize their audio experience, whether they are listening to their favorite vinyl records or streaming high-resolution digital files.

Overall, the MartinLogan 1000 stands out as a premium choice for serious music enthusiasts. Its combination of electrostatic technology, precise imaging, and elegant design make it a top contender in the high-end speaker market. For those who demand exceptional audio fidelity and aesthetic beauty, the MartinLogan 1000 delivers, making it an investment worth considering for any serious home audio setup.
Top Page Image Contents