Toshiba MR-3018 service manual Solenoid

Page 58

4.4Solenoid

[A]Original pickup solenoid (SOL1)

(1)Take off the original feed motor drive section.

( P.4-21 "[E] Original feed motor drive sec- tion")

(2)Disconnect one connector. Remove 2 screws and take off the original pickup sole- noid with the bracket.

Screw

 

Connector

Original pickup solenoid

Fig.4-66

(3)Remove 2 screws and take off the original pickup solenoid from the bracket.

Note:

When installing the original pickup solenoid, be sure to align the edge of the original pickup solenoid with the mark-off line on the frame.

Original pickup solenoid

Bracket

Fig.4-67

Mark-off line

Fig.4-68

MR-3018 DISASSEMBLY AND ASSEMBLY

June 2005 © TOSHIBA TEC

4 - 24

Image 58
Contents MR-3018 Toshiba TEC Corporation Page Page Contents Circuit Diagram / Harness Diagram Specification MR-3018 Specification June 2005 Toshiba TEC General Description Main ComponentsSectional View FLP2Electric Parts Layout Symbols and Functions of Various Components MotorsDiagram of Signal Blocks REQ ACK DF-REQ DF-ACK SCAN-ST CNT CPUDescription of Interface Signals Description of Operations OutlineOriginal feed motor drive section Read motor drive section Original exit/reverse motor drive section Original Size Detection Original tray width sensorA4 series width sizes mixed at A3 / A4 standard LT series ORG-SRS Flow Chart ON? YES Certain period YES Gate solenoid on Transport request Signal received? Exposure and scanning start Original END Description of Circuit Drive Circuit for Feed MotorDrive Circuit for Read Motor Drive Circuit for Exit Motor Drive Circuit for FAN MotorReset Circuit Drive Circuit for Pickup SolenoidDrive Circuit for Gate Solenoid Disassembly and Assembly CoverRear cover Pin Dial Clip Left cover Remove 2 screws and take off the left cover Original tray Take off the front cover Original reverse tray Take off the original tray Roller Pickup roller PM Take off the paper feeder unit Slide the pulley and remove 1 pin Separation roller PM Take off the paper feeder unit Feeder lower guide Take off the original tray Registration roller Take off the feeder lower guide Exit guide Pre-reading lower guide Connector Flange Upper guide Reverse registration Motor / Motor drive section Spring Remove 3 screws and then take off the bracket Spring Bushing Harness clamp Ring Bracket Screw Original exit/reverse motor M3 Solenoid Mark-off line Sensor/switch Remove 2 screws and take off the holder Jam access cover sensor Original empty sensor Actuator Connector Holder Original exit/reverse sensor Opening/closing PC Board Others Hinge stopperMR-3018 Disassembly and Assembly Adjustment Adjustment of PositionMR-3018 Adjustment June 2005 Toshiba TEC Loosen the hinge screws at the front side Match the screw hole positions June 2005 Toshiba TEC MR-3018 Adjustment Adjustment of Height ~0.5mm 0mmTurn it counterclockwise Heightened Adjustment of Skew 17 Chart OriginalShift the aligning plate in the direction of + MR-3018 Adjustment June 2005 Toshiba TEC Adjustment of the Leading Edge Position 24 Chart OriginalMR-3018 Adjustment June 2005 Toshiba TEC Adjustment of Horizontal Position Adjustment of Copy Ratio Adjustment of Radf Opening/Closing Sensor MR-3018 Adjustment June 2005 Toshiba TEC Troubleshooting Troubleshooting for Mechanical ErrorsTroubleshooting for Electrical Errors YES MR-3018 Troubleshooting June 2005 Toshiba TEC Maintenance and Rewriting ROM Periodic MaintenanceRewriting ROM Firmware Updating Circuit Diagram / Harness Diagram Assembly of PC BoardDiagram CircuitOriginal tray sensor Original tray width sensor Control PC Board Circuit MR-3018 Circuit Diagram / Harness Diagram MR-3018 Circuit Diagram / Harness Diagram June 2005 Toshiba TEC MR-3018 Circuit Diagram / Harness Diagram June 2005 Toshiba TEC MR-3018 Circuit Diagram / Harness Diagram
Related manuals
Manual 122 pages 40.04 Kb