•When connecting an unbalanced output to a bal- anced input, be sure that the signal high (hot) connections are wired to each other. The unbal- anced ground (earth) connection should be wired to the low (cold) and the ground (earth) connec- tions of the balanced input. If there are
(earth) connection, leaving the unbalanced ground connected to the balanced input low (cold) con- nection only.
In some cases, you may have to make up special adapters to interconnect your equipment. For example, you may need a balanced XLR female connected to an unbalanced 1/4" TS phone plug. Many common adapters can be found at your local electronics supply store.
DB25 Connectors
Analog
The BALANCED LINE LEVEL INPUTs and BALANCED LINE LEVEL OUTPUTs on the back of the Onyx 800R provide balanced inputs and outputs for channels
Each DB25 connector provides eight balanced line- level inputs or outputs.
|
| CH 1 | CH 2 |
| CH 3 | CH 4 | CH 5 |
| CH 6 | CH 7 |
| CH 8 | |||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| GROUND COLD HOT | GROUND COLD HOT GROUND | COLD HOT | GROUND COLD HOT GROUND | COLD HOT | GROUND COLD HOT GROUND | COLD HOT | GROUND COLD HOT | ||||||||||||||||||||||||||||||||||||||
N/C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
13 |
|
| 12 |
|
| 11 |
|
| 10 |
|
| 9 |
|
|
| 8 |
|
|
| 7 |
|
|
| 6 |
|
|
| 5 |
|
|
| 4 |
|
|
| 3 |
|
|
| 2 |
|
|
| 1 |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
25 24 23 | 22 21 20 19 18 17 16 15 14 |
Analog DB25
Several companies make
DB25 cables that break out to XLR, 1/4" TRS, or TT connectors for connecting to other mixers or audio gear are also readily available. See your Mackie dealer for details.
Digital |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Owner’s | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
The AES/EBU OR S/PDIF OUT connector provides | Manual | ||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| USED ON |
|
|
|
| ||||||||
a digital output for all eight channels. If you have this |
| ||||||||||||||||||||||||||||||||||||||||||||||
output configured for AES/EBU, which is a balanced |
| ||||||||||||||||||||||||||||||||||||||||||||||
output, the connector is wired as follows: |
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| INPUTS NOT |
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ONYX 800R |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (110 Ω TERMINATION) |
| |||||||||||||||
|
|
| SHIELD CH7/8 OUT– | CH 7/8 OUT+ CH 5/6 OUT– CH 5/6 OUT+ | CH 3/4 OUT– CH 3/4 OUT+ | CH 1/2 OUT– CH 1/2 OUT+ |
|
|
|
|
|
| |||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
SHIELD SHIELD SHIELD SHIELD NC SHIELD SHIELD SHIELD | CH 7/8 IN– CH 7/8 IN+ | CH 5/6 IN– | CH 5/6 IN+ CH 3/4 IN– CH 3/4 IN+ | CH 1/2 IN– CH 1/2 IN+ |
| ||||||||||||||||||||||||||||||||||||||||||
13 |
|
| 12 |
|
| 11 |
|
| 10 |
|
| 9 |
|
|
| 8 |
|
|
| 7 |
|
|
| 6 |
|
| 5 |
|
|
|
| 4 |
|
|
| 3 |
|
|
| 2 |
|
|
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
25 24 23 22 21 20 19 18 17 16 15 14 |
|
|
Digital DB25 AES/EBU Output
If you have this output configured for S/PDIF, which is an unbalanced output, the connector is wired as follows:
INPUTS NOT
USED ON
ONYX 800R
(110 Ω TERMINATION)
SHIELD SHIELD | SHIELD SHIELD | NC SHIELD | SHIELD SHIELD | SHIELD CH 7/8 GND | CH 7/8 OUT CH 5/6 GND CH 5/6 OUT CH 3/4 GND | CH 3/4 OUT CH 1/2 GND | CH 1/2 OUT NC NC NC | NC NC | NC NC NC |
13 |
|
| 12 |
|
| 11 |
|
| 10 |
|
| 9 |
|
| 8 |
|
| 7 |
|
| 6 |
|
| 5 |
|
| 4 |
|
| 3 |
|
| 2 |
| 1 |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25 24 23 22 21 20 19 18 17 16 15 14
Digital DB25 S/PDIF Output
If you are using the DUAL WIRE position with the higher sample rates (88.2 kHz and up), the same cabling that you use for the SINGLE WIRE position will work as long as you have it connected to another device using the same method.
Note: A variety of alternate
Owner’s Manual | 19 |