APC PMP3XS-B, PMJ3XS-B, PMH3XS-B, PML3XS-B, PMG3XS-B, PMF3XS-B operation manual Introduction, Testing

Page 6

Introduction

Introduction

Thank you for choosing the APC SurgeArrest® PM_3X Series “Brick” Surge Protective Device.

The APC non-modular Surge Protective Device (SPD) is a high-quality, high-energy surge attenuation system that has been designed to protect sensitive equipment from damaging transient voltage surges. Proper installation is imperative to maximize the surge suppressor’s effectiveness and performance.

This manual is to be used as a guide for installing the device. Read and understand all information contained in this manual prior to installation. The outlined procedures are not intended to supersede local or national electrical codes. Check all applicable electrical codes to assure compliance.

This device must be installed by qualified electrical personnel. The installer should follow the steps detailed in this manual to ensure proper installation. A copy of the installer’s invoice, detailing the installation of this device, is required in order to take advantage of the unit’s product warranty.

The SurgeArrest® PM_3X Series product lines specify a parallel SPD designed for service entrance and downstream panelboard applications. These units provide replaceable “brick” (all included surge protections are encapsulated into a single “brick” module) surge protection and are available in 120 kA phase rating.

All APC products are extensively tested according to industry standards as set by IEEE C62.41 and C62.45 for Type 2 Applications. Type 2 applications are permanently connected to SPDs intended for installation on the load side of the service equipment overcurrent device; including SPDs at the branch panel.

Save this manual! It includes instructions regarding the product warranty and replacement parts.

Testing

Any factory or on-site testing that exceeds the normal operating voltage, such as high-potential insulation testing or other tests where the suppression components will be subjected to voltages higher than their rated “turn on” voltage, must be run with the suppressor disconnected from the power source. For 4-wire devices, the neutral connection at the SPD must also be disconnected prior to performing high-potential testing and then reconnected upon completion of the test.

Failure to disconnect this surge suppression device and its associated suppression components during elevated voltage testing will result in damage to the suppression components and/or other electronic components.

6

Installation and Operation Manual

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation PMF3XS-B PMJ3XS-B PMP3XS-B PMH3XS-B PMG3XS-B PML3XS-BPage Table of Contents Loss of Branch Circuit POWER/LOSS of Surge Suppression PrecautionsPrecautions Hazard of Electric SHOCK, EXPLOSION, or ARC FlashLoss of Surge Suppression Testing IntroductionIntroduction Hazard of Electric SHOCK, EXPLOSION, or ARC Flash Inspection SPD Nameplate ExampleVoltage Rating ElectricalElectrical Voltage RatingsTerminals, Wire Size, and Installation Torque Branch Circuit Overcurrent Protection and Disconnect MeansLocation Location of SPDGrounding GroundingHazardous Touch Voltage Installation InstallationCables are removed, reconnect the cables as marked Wiring WiringWiring Diagrams without Integral Switch SIngle-Phase, Three-Wire, Grounded InstallationLED Status Indicators OperationOperation Audible Alarm Surge Counter SurgeArrest Replacement ModulesDry Contact Configuration Dry ContactsMaintenance Preventive MaintenanceReplacement Parts TroubleshootingTroubleshooting Troubleshooting FlowchartPage Page Page APC Worldwide Customer Support

PML3XS-B, PMJ3XS-B, PMH3XS-B, PMF3XS-B, PMP3XS-B specifications

The APC PMG3XS-B, PMJ3XS-B, PMH3XS-B, PML3XS-B, and PMF3XS-B are part of APC’s renowned line of power management solutions, designed to provide effective power protection and management for sensitive electronic equipment. Each model in this series offers unique features tailored to different application needs, yet they all share a commitment to the core standards of reliability, efficiency, and user-friendliness.

Starting with the PMG3XS-B, this model is equipped with advanced power conditioning technology, ensuring that connected devices receive a clean and stable power supply. Its compact design allows for easy installation in various environments, making it suitable for both home and office use. Featuring an LCD display, users can monitor the device's performance in real-time, providing insights into power usage and status alerts.

The PMJ3XS-B is designed with enhanced surge protection capabilities, safeguarding electronics from sudden voltage spikes. It features a robust build quality that ensures durability and longevity, making it an ideal choice for users needing reliable equipment for critical operations. Its smart charging capability optimizes power usage while maintaining the health of connected devices.

The PMH3XS-B emphasizes high-efficiency power management, with energy-saving features that reduce unnecessary power consumption. This model supports multiple output configurations, accommodating various plug types and ensuring versatility in managing different devices. It's particularly beneficial for businesses aiming to minimize energy costs while sustaining performance.

For users seeking a lightweight and portable solution, the PML3XS-B stands out. Perfect for on-the-go professionals, this model offers a slim design without compromising essential power management features. Its compatibility with various devices makes it a favorite for users who require power solutions across different locations.

Lastly, the PMF3XS-B combines all the strengths of its counterparts, focusing on advanced filtering technology to eliminate power line noise. This feature is crucial for sensitive equipment, ensuring optimal performance and longevity. With its comprehensive monitoring capabilities, users can easily assess power quality and make informed decisions about their energy usage.

In summary, the APC PMG3XS-B, PMJ3XS-B, PMH3XS-B, PML3XS-B, and PMF3XS-B provide a comprehensive suite of power management options designed for diverse applications. Their commitment to performance, efficiency, and user convenience makes them an exceptional choice for anyone looking to protect their electronic devices effectively.
Top Page Image Contents