D-Link DSL-500G manual Quick Configuration

Page 27

DSL-500G ADSL Router User’s Guide

Quick Configuration

The Quick Configuration displays the settings you are most likely to need to change when you first set up the Router. These settings are explained briefly below:

 

Select the ATM interface you want to use (use atm-0 for a single

ATM Interface

ATM interface). Your system may be configured with more than one

ATM interface if you are using different types of services with your

 

 

ISP. See ATM VC Configuration.

 

 

 

This setting enables or disables the device's Internet and routing

Operation Mode

functions. When set to "No", the device cannot be used to provide

 

Internet connectivity for your network.

 

 

Encapsulation

This setting determines the type of data link used to communicate

with your ISP. See ATM VC Configuration.

 

 

 

VPI and VCI

These settings determine the unique data path your modem uses to

communicate with your ISP. See ATM VC Configuration.

 

 

 

Bridge

This setting enables or disables bridging between the device and

your ISP. Your ISPs may also refer to this using "RFC 1483" or

 

"Ethernet over ATM". See Bridging.

 

 

IGMP

This setting enables or disables the Internet Group Management

Protocol, which some ISPs use to perform remote configuration of

 

your device.

 

 

 

If your ISP has assigned a public IP address to your LAN, enter the

IP Address and Subnet

address and the associated subnet mask in the boxes provided.

Check with your ISP to get this information. You may have to use the

Mask

public IP address for your computer. In this case you do not enter the

 

 

IP address here but configure these settings for your computer.

 

 

 

When enabled, this setting specifies that the IP address specified

Default Route

above will be used as the default route for your LAN. Whenever, one

of your LAN computers attempts to access the Internet, the data will

 

 

be sent via the WAN interface.

 

 

Gateway IP Address

Specify the IP address that identifies the ISP server through which

your Internet connection will be routed.

 

 

 

 

Enter the username and password you use to log in to your ISP.

Username and Password

(Note: this is not the same as the user name and password you used

 

to log in to Web Configuration Manager.)

 

 

 

Click Enable to turn on the DNS forwarding service, which forwards

 

to your LAN PCs the Domain Name System server addresses that

Use DNS

your PPP connection learns from your ISP. This option can only be

used when the Router is configured to act as a DHCP server for your

 

PCs.

 

If you click Disable, you must configure DNS addresses manually on

 

each PC or in the fields below.

 

 

Primary/Secondary DNS

Enter the Primary and Secondary DNS server addresses provided by

your ISP.

 

 

 

Click the Submit button to save the settings in temporary memory. When you are done making changes to the configuration settings, open the Commit & Reboot menu and click the Commit button to save your changes to permanent memory.

You can click the Delete button to remove all existing Quick Configuration settings and return to the default values.

17

Image 27
Contents DSL-500G Adsl Router Limited Warranty Wichtige SicherheitshinweiseHardware Software Link Offices for Registration and Warranty ServiceTrademarks Copyright StatementFCC Warning Contents Figures Guide Overview Installation OverviewRequirements Before You StartWeb Browser Router vs. Bridge ModeAdditional PVC Settings Operating SystemPacking List Page Router Features What is ADSL?Router Description and Operation Rear Panel Front PanelComputer to Router Connection Hardware InstallationConnect Ethernet LAN to Router Connect Adsl LinePower On Router Hub or Switch to Router ConnectionWan Configuration Summary Configuring IP Settings on Your ComputerConfigure Windows XP for Dhcp DSL-500G Adsl Router User’s Guide DSL-500G Adsl Router User’s Guide Windows Configure Windows 2000 for DhcpConfigure Windows ME for Dhcp Windows MEWindows 95 Configure Windows 95, 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 workstations Check for Proxy service in Windows Internet Explorer Access the Web Configuration ManagerWeb-based Manager Main Menu First Time Log On Quick Configuration Window Configure WAN Connection Adsl Service ConnectionCommit and Reboot Menu Commit & RebootManager Interface Layout Web Configuration Management GuideQuick Configuration WAN Interface Services SummaryHome Page System View DeviceLAN IP Address Change LAN IP SettingsSystem Mode Get LAN IP AddressDhcp Mode Configuration Dhcp Service ModesWAN Configuration Options ATM VC ConfigurationAdditional Virtual Connections VCC Interface Mux TypeMAX Proto per AAL5 PPP Configuration PPP ConfigurationPPP Interface Service NameLogin Name Login PasswordNetmask IpoA ConfigurationIPoA Interface Conf. IP AddressAdd IPoA Interface EOA Configuration EOA ConfigurationNet Mask EOA InterfaceBridge Configuration Bridge Configuration Menu IP Route Routing ConfigurationAdding IP Routes IP AddressNAT Local Address To Rule IDLocal Address FromRIP Firewall Firewall ConfigurationManaging the Black List IP Filter IP Filter ConfigurationIP Filter Rule Add Adding an IP Filter RuleDSL-500G Adsl Router User’s Guide DSL-500G Adsl Router User’s Guide DNS Configuration Configuring DNS RelayDSL-500G Adsl Router User’s Guide Blocked Protocols Blocked ProtocolsChange User Password Changing the Manager PasswordReboot the Router Commit & RebootReboot From Default Reboot OptionsImage Upgrade ConfigurationDiagnostics Window DiagnosticsAlarm/Trap Information AlarmsTechnical Specifications In-Line Filters In-line Filter InstallationSplit Line Filter Split Line Filter InstallationOffices Norway Link Norway Print, type or use block letters Registration Card