NETGEAR WPN802 manual Understanding Advanced Wireless Settings

Page 31

Reference Manual for the NETGEAR RangeMax™ Wireless Access Point WPN802

•Country/Region: It may not be legal to operate the access point in a country/region other than the country/region shown here. See online help for more details. To change the Country/ Region, select from the drop-down list. The region selection feature may not be available in all countries.

•Wireless Network Name (SSID): The default is NETGEAR. Enter a 32-character (maximum). The characters are case sensitive.

Note: You will not get a wireless network connection unless the network SSID matches exactly what is configured in the access point.

•Broadcast Wireless Network Name (SSID): If enabled, the Wireless Access Point will broadcast its SSID. If set to disable, the SSID is not broadcast.

•Operating Mode: Select the desired wireless operating mode. The default is Auto (11g/11b). You can change this to 11g Only, or 11b Only.

•Channel/Frequency: Select the channel for your wireless LAN. This feature is disabled if AutoCell is enabled. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby access point. For more information on the wireless channel frequencies please refer to “Wireless Channels” on page B-7.

•Data Rate: The available transmit data rate of the wireless network. Note that 108 Mbps option is available when the Channel/Frequency is set to channel 6 and the operating mode is set to 11g Only.

•Output Power: Shows the available transmit power of the access point. The possible Tx

power options are: Full, 50%, 25%, 12.5%, and minimum. The transmit power may varies depends on the local regulatory regulations. Note that this feature will be disabled if AutoCell is enabled.

Understanding Advanced Wireless Settings

To configure the advanced wireless settings of your wireless access point, click the Wireless Setup link in the Advanced section of the main menu of the browser interface. The Wireless Settings menu appears, as shown below.

Wireless Configuration

4-3

202-10101-01, 4 May 2005

Page 30 Page 32
Image 31
Page 30 Page 32
Contents NETGEAR, Inc 202-10101-01, May Product and Publication Details 202-10101-01, May Contents Chapter Management and Information Glossary Viii Contents Audience, Scope, Conventions, and Formats Chapter About This ManualHow to Print this Manual How to Use This ManualPrinting the Full Manual 202-10101-01, May Chapter Introduction Key FeaturesRangeMax Multi-In, Multi-Out Mimo Technology Autosensing Ethernet Connections with Auto Uplink 802.11g Wireless NetworkingPackage Contents Rear Panel Front Panel Status Lights202-10101-01, May 202-10101-01, May Default Factory Settings Chapter Basic Installation and ConfigurationFirst, Connect the Wireless Access Point to Your Computer Prepare to Install Your Wireless Access PointSystem Requirements WPN802 connected to a computer during configuration WPN802 Settings Then, Configure the Basic SettingsBasic Settings menu Wireless Settings menu Next, Configure the Wireless SettingsWPN802 placed in a vertical orientation Deploy the WPN802 and Verify Wireless ConnectivityLogin window How to Log In to the WPN802 Using Its Default IP AddressBrowser display the WPN802 settings home 202-10101-01, 4 May Observe Performance, Placement, and Range Guidelines Chapter Wireless ConfigurationVertical orientation required on metallic surfaces Understanding Wireless SettingsUnderstanding Advanced Wireless Settings Advanced Wireless Settings menu Wireless Data Security Options Implementing Appropriate Wireless Security202-10101-01, 4 May If WPA-PSK Authentication is Used How to Set Up and Test Basic Wireless Connectivity How to Configure WEP or WPA Wireless Settings encryption menu Advanced Wireless Settings Configuring Advanced Wireless SettingsWireless Access Control List screen Wireless Card Access Restricting by MAC AddressSetting up the Access Control List Turning Access Control On202-10101-01, 4 May Chapter Management and Information Changing the PasswordFirst, Prepare for the Firmware Upgrade Upgrading the Wireless Access Point FirmwareThen, Upgrade the Firmware Upgrade Firmware dialog box Backing up Settings or Restoring SettingsRestoring Settings from a Backup File Backing up SettingsRestoring Factory Default Settings Viewing a List of Available Wireless Stations Rebooting the WPN802 Access PointStatistics screen Viewing StatisticsEthernet light is not lit Chapter TroubleshootingTroubleshooting Tips No lights are lit on the access pointWhen I enter a URL or IP address I get a timeout error Cannot configure the access point from a browserTo clear all data and restore the factory default values Using the Reset Button to Restore Factory Default Settings202-10101-01, May Power Adapter Appendix a Technical SpecificationsWireless Wireless Networking Overview Appendix B Wireless Networking BasicsInfrastructure Mode Ad Hoc Mode Peer-to-Peer Workgroup Authentication and WEP Data EncryptionNetwork Name Extended Service Set Identification Essid Open System Authentication Authentication802.11b Authentication Open System Steps 802.11b Authentication Shared Key Steps Key Size WEP Configuration Options Wireless ChannelsWPA and WPA2 Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to WPA2 Ieee 802.11i? What are the Key Features of WPA and WPA2 Security?Wireless Networking Basics Figure B-3 WPA/WPA2 Overview Access point replies with an EAP-request identity message WPA/WPA2 Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA/WPA2 Is WPA/WPA2 Perfect?Changes to Wireless Access Points Changes to Wireless Client Programs Glossary 802.11e Standard Access Point AP Bridge CSMA/CD Carrier Sense Multiple Action/Collision Detection Essid more commonly referred to as Ssid Short Set Identifier Ieee Institute of Electrical and Electronics Engineers MAC Media Access Control PHY Range Site survey TCP/IP War Driving Wi-Fi Protected Access and Ieee 802.11i Comparison Wi-Fi Protected Access in Mixed Mode Deployment Glossary
Related manuals
Manual 2 pages 30.82 Kb

WPN802 specifications

The NETGEAR WPN802 is an exceptional wireless access point that has made a significant impact on the home networking landscape. Designed to provide robust wireless connectivity, the WPN802 is an 802.11g compliant device, delivering reliable performance at data rates of up to 54 Mbps. This allows users to enjoy seamless Internet access for streaming, gaming, and other bandwidth-intensive applications.

One of the standout features of the NETGEAR WPN802 is its ease of installation and setup. The device is equipped with a user-friendly setup wizard that guides users step by step through the process, making it accessible even for those who may not be tech-savvy. The WPN802 also supports both wired and wireless connections, allowing it to integrate seamlessly into existing network configurations, whether expanding a home network or setting up a new one.

Security is a crucial aspect of any wireless network, and the WPN802 addresses this with several built-in security features. It supports WEP, WPA, and WPA2 encryption protocols, ensuring that data transmitted over the network remains secure from unauthorized access. Additionally, the device provides MAC address filtering, which allows users to control the devices that can connect to the network.

Another significant feature of the NETGEAR WPN802 is its versatility. It can function not only as an access point but also as a wireless bridge or a repeater, enabling users to extend the range of their existing wireless network. This flexibility is particularly valuable in larger homes or offices where coverage may be spotty in certain areas.

The WPN802 also includes Quality of Service (QoS) features that prioritize bandwidth for different applications, ensuring that critical tasks such as video conferencing and online gaming receive the necessary resources for optimal performance. This enhances the overall user experience, especially in environments with multiple connected devices.

In terms of build and design, the NETGEAR WPN802 is compact and lightweight, allowing for easy placement in various locations without being obtrusive. Its stylish exterior ensures it can fit in seamlessly with home or office decor.

In conclusion, the NETGEAR WPN802 is a highly reliable and feature-rich wireless access point that caters to the needs of modern users. With its fast wireless speeds, robust security features, versatile functionality, and user-friendly setup, it remains a commendable choice for anyone looking to enhance their wireless networking experience. Whether used in a residential or small business setting, the WPN802 stands out as a dependable solution that continues to meet the demands of today's connected world.
Top Page Image Contents