NETGEAR WG102 manual Antenna Statement for the European Community

Page 9

Antenna Statement for the European Community

Please note that the 100mW EIRP limit and regulations could vary in Europe from country to country. Please check the regulations in your country.

The antenna cable type and length must comply with European regulations. Refer to the table below for approved antenna and cable accessories.

In addition to its own antenna, the WG102 device has been approved for use with the following detachable antennas and antenna cables:

Approved

Antenna Gain

Approved

Minimum

Minimum

Maximum

Antennas

and type

Antenna Cable

Antenna

Antenna

Transmitted

 

 

 

Cable

Cable

Power*

 

 

 

Length

Attenuation

 

NETGEAR

18 dBi,

NETGEAR

 

 

-3 dBm + 18 dBi

directional

30 m

18 dB

ANT24D18

ACC-10314-05

= 15 dBm EIRP

outdoor/indoor

 

 

 

 

 

 

 

 

 

 

 

 

 

NETGEAR

9 dBi,

NETGEAR

 

 

 

ACC-10314-04

 

 

8.9 dBm + 9 dBi

omnidirectional

10 m

6.1 dB

ANT2409

or

= 17.9 dBm EIRP

outdoor/indoor

 

 

 

ACC-10314-05

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NETGEAR

5 dBi, ceiling/wall

NETGEAR

 

 

14 dBm + 5 dBi

ACC-10314-01

1.5 m

1.1 dB

ANT24O5

indoor

= 19 dBm EIRP

thru 05

 

 

 

 

 

 

 

 

 

 

 

 

 

* WG102 maximum radiated power in the European Community: 15 dBm – cable loss + antenna gain

Please go to www.netgear.com and use the search feature to find an updated list of wireless accessories approved to be used with the WG102 in the European Community.

Bestätigung des Herstellers/Importeurs

Es wird hiermit bestätigt, daß das NETGEAR WG102 ProSafe 802.11g Wireless Access Point gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.

Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.

Certificate of the Manufacturer/Importer

It is hereby certified that the NETGEAR WG102 ProSafe 802.11g Wireless Access Point has been suppressed

in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some

9

October 2004

Image 9
Contents October Technical Support FCC Statement RF Exposure Warning for North America, and Australia Antenna Statement for North America and Australia 0681 Requirements For Operation in the European Community October Antenna Statement for the European Community October Contents Appendix a Specifications Appendix B Wireless Networking Basics Contents Audience, Versions, Conventions Chapter About This ManualHtml version of this manual How to Use this ManualHow to Print this Manual About This Manual Chapter Introduction Supported Standards and Conventions Key FeaturesAutosensing Ethernet Connections with Auto Uplink 802.11g Standards-based Wireless NetworkingCompatible and Related Netgear Products System RequirementsWhat’s In the Box? Need Product Photo Or Illustration Hardware DescriptionDetachable Antenna Observing Placement and Range Guidelines Chapter Basic Installation and ConfigurationCabling Requirements Feature Factory Default Settings Default Factory SettingsLUHOHVVDWD 6HFXULW\2SWLRQV Understanding WG102 Wireless Security OptionsSET UP the WG102 Access Point Installing the WG102 Access PointLogin window Web browser will then display the WG102 settings Configure the settings appropriate for your network Deploy the WG102 Access Point Verify Wireless Connectivity How to Log In to the WG102 Using Its Default IP Address Understanding Basic Wireless Settings Basic Installation and Configuration Understanding WEP/WPA Security Options Wireless Security SettingsWireless LAN options are explained in the following table Field Description WPA-PSK Wi-Fi WEP Encryption Keys Before You Change the Ssid and WEP SettingsHow to Set Up and Test Basic Wireless Connectivity Select the Turn Access Control On check box How to Restrict Wireless Access by MAC AddressTo configure WEP data encryption, follow these steps How to Configure WEPHow to Configure WPA 11 Wireless Settings menu 13 Wireless Settings menu How to Configure WPA-PSKIP Address Using the Basic IP Settings OptionsTime Zone Chapter Management Using Syslog and Activity Log InformationThis screen shows the following parameters Viewing General, Log, Station, and Statistical InformationGeneral Information Fields Statistics Field Description Wired Ethernet Received/TransmittedViewing a List of Attached Devices Upgrading the Wireless Access Point SoftwareSettings Backup menu Configuration File ManagementSaving and Retrieving the Configuration Restoring the WG102 to the Factory Default SettingsUsing the Reset Button to Restore Factory Default Settings Set Password menu Changing the Administrator PasswordRemote Management settings Using Snmp Remote ManagementManagement Hotspot Settings Chapter Advanced ConfigurationTable below describes the advanced wireless parameters Configuring Advanced Wireless SettingsPoint-to-Point Bridge AP Settings Enabling Wireless Bridging and RepeatingRepeater with Wireless Client Association How to Configure a WG102 as a Point-to-Point BridgeMulti-Point bridging How to Configure Multi-Point Wireless BridgingAdvanced Configuration How to Configure Wireless Repeating Advanced Configuration No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upCannot connect to the WG102 to configure it When I enter a URL or IP address I get a timeout errorUsing the Reset Button to Restore Factory Default Settings October Specifications for the WG102 Appendix a SpecificationsWPA Appendix B Wireless Networking Basics Wireless Networking OverviewInfrastructure Mode Authentication and WEP Data Encryption Ad Hoc Mode Peer-to-Peer WorkgroupNetwork Name Extended Service Set Identification Essid Open System Authentication Authentication802.11b Authentication Open System Steps 802.11b Authentication Shared Key Steps Key Size WEP Configuration Options Wireless ChannelsWPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Wireless Networking Basics Figure B-3 WPA Overview Access point replies with an EAP-request identity message WPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect?Changes to Wireless Access Points Changes to Wireless Client Programs Glossary Dhcp DSL Internet service provider Radius TLS Wins Glossary Numerics IndexWEP B-3
Related manuals
Manual 2 pages 31.24 Kb Manual 23 pages 35.1 Kb Manual 2 pages 35.77 Kb

WG102 specifications

The NETGEAR WG102 is a robust and versatile wireless access point designed to enhance network connectivity in a variety of environments, from small businesses to larger enterprise settings. This device is well-regarded for its ease of use, reliable performance, and a feature set that caters to both basic and advanced networking needs.

One of the key features of the WG102 is its support for the IEEE 802.11g standard, which provides data rates of up to 54 Mbps. This makes it suitable for high-speed internet access and seamless data transfer for users connected to the network. Additionally, the WG102 is backward compatible with the 802.11b devices, ensuring that existing hardware can be integrated into the network without issues, thereby protecting investment in older technology.

The WG102 also excels in its deployment flexibility. With Power over Ethernet (PoE) support, installation becomes significantly easier, as the access point can receive power through the Ethernet cable, eliminating the need for additional power outlets. This feature is particularly advantageous in locations where power supply access is limited or where aesthetic considerations are key.

Security is a vital aspect of any network, and the WG102 does not disappoint. It supports Wi-Fi Protected Access (WPA and WPA2) for secure wireless communications, ensuring that user data is encrypted and protected from potential threats. The device also features WEP encryption, allowing users to implement various security measures based on their specific needs.

The WG102's management capabilities include a web-based interface, enabling administrators to configure settings easily and monitor network performance. The device supports VLAN tagging, which can help in segmenting network traffic for better performance and security. The ability to manage multiple access points through a single interface also streamlines network management.

In terms of physical characteristics, the NETGEAR WG102 is designed for durability and reliability. Its compact form factor allows for discreet installation, whether mounted on a ceiling, wall, or placed on surfaces.

Overall, the NETGEAR WG102 is a dependable access point that offers a combination of speed, security, and ease of management, making it an excellent choice for those looking to enhance their wireless networking capabilities.