Aruba Networks FIPS 140-2 manual Configuring Remote Mesh Point Fips Mode

Page 20

represents the only exception. That is, nothing other than a PoE injector should be present between the module and the staging controller.

8.Once the module is connected to the controller by the Ethernet cable, navigate to the

Configuration > Wireless > AP Installation page, where you should see an entry for the AP. Select that AP, click the “Provision” button, which will open the provisioning window. Now provision the AP as Remote Mesh Portal by filling in the form appropriately. Detailed steps are listed in Section “Provisioning an Individual AP” of Chapter “The Basic User-Centric Networks” of the Aruba OS User Guide. Click “Apply and Reboot” to complete the provisioning process.

a.During the provisioning process as Remote Mesh Portal, if Pre-shared key is selected to be the Remote IP Authentication Method, the IKE pre-shared key (which is at least 8 characters in length) is input to the module during provisioning. Generation of this key is outside the scope of this policy. In the initial provisioning of an AP, this key will be entered in plaintext; subsequently, during provisioning, it will be entered encrypted over the secure IPSec session. If certificate based authentication is chosen, AP’s RSA key pair is used to authenticate AP to controller during IPSec. AP’s RSA private key is contained in the AP’s non volatile memory and is generated at manufacturing time in factory.

b.During the provisioning process as Remote Mesh Portal, the WPA2 PSK is input to the module via the corresponding Mesh cluster profile. This key is stored on flash encrypted.

9.Via the logging facility of the staging controller, ensure that the module (the AP) is successfully provisioned with firmware and configuration

10.Terminate the administrative session

11.Disconnect the module from the staging controller, and install it on the deployment network; when power is applied, the module will attempt to discover and connect to an Aruba Mobility Controller on the network.

To verify that the module is in FIPS mode, do the following:

1.Log into the administrative console of the Aruba Mobility Controller

2.Verify that the module is connected to the Mobility Controller

3.Verify that the module has FIPS mode enabled by issuing command “show ap ap-name <ap- name> config”

4.Terminate the administrative session

3.3.4 Configuring Remote Mesh Point FIPS Mode

1.Apply TELs according to the directions in section 3.2

2.Log into the administrative console of the staging controller

3.Deploying the AP in Remote Mesh Point mode, create the corresponding Mesh Profiles on the controller as described in detail in Section “Mesh Points” of Chapter “Secure Enterprise Mesh” of the Aruba OS User Manual.

a.For mesh configurations, configure a WPA2 PSK which is 16 ASCII characters or 64 hexadecimal digits in length; generation of such keys is outside the scope of this policy.

4.Enable FIPS mode on the controller. This is accomplished by going to the Configuration > Network

>Controller > System Settings page (this is the default page when you click the Configuration tab), and clicking the FIPS Mode for Mobility Controller Enable checkbox.

5.Enable FIPS mode on the AP. This accomplished by going to the Configuration > Wireless > AP Configuration > AP Group page. There, you click the Edit button for the appropriate AP group, and then

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Fips 140-2 Non-Proprietary Security Policy Page Services Aruba Dell Relationship Acronyms and AbbreviationsAruba AP-120 Series Security Levels Physical SecurityPage Introduction Aruba Dell RelationshipAcronyms and Abbreviations GHzLAN Product Overview Aruba AP-120 SeriesPhysical Description Aruba Part Number Dell Corresponding Part NumberEnet Indicator LEDs Label Function Action StatusPWR Label Function Action Status Module Objectives Security LevelsPhysical Security Applying TELsAruba AP-124 TEL Placement AP-124 Front viewAP-124 Back view Aruba AP-125 TEL Placement AP-124 Bottom viewAP-125 Front view AP-125 Right view Inspection/Testing of Physical Security Mechanisms AP-125 Bottom viewConfiguring Remote AP Fips Mode Modes of OperationEnable Fips mode on the AP. This accomplished by going to Configuring Remote Mesh Portal Fips Mode Configuring Remote Mesh Point Fips Mode Verify that the module is in Fips mode Operational EnvironmentLogical Interfaces Fips 140-2 Logical Interfaces Module Physical InterfaceRoles Roles, Authentication and ServicesCrypto Officer Authentication User Authentication Wireless Client AuthenticationStrength of Authentication Mechanisms Authentication Mechanism StrengthWPA2-PSK Services Crypto Officer ServicesService Description CSPs Accessed see section WPA2 PSKService User ServicesService Description CSPs Wireless Client Services Unauthenticated Services ∙ FTP ∙ Tftp ∙ NTPCryptographic Algorithms Non-FIPS Approved AlgorithmsCritical Security Parameters HmacRNG AES-CCM PSKPTK GMK GTKSelf Tests For an AES Cavium hardware Post failure
Top Page Image Contents