Linksys BEFSR41W manual Through IPSec is supported

Page 28

Instant BroadbandTM Series

The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen. What do I need to do? Force your NIC to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your NIC as a temporary measure. (Please look at the Network Control Panel, in your Ethernet Adapter’s Advanced Properties tab.). Make sure that your proxy setting is disabled in the browser. Check our website at www.linksys.com for more information.

If all else fails in the installation, what can I do? Reset the router by holding down the reset button for at least three seconds and reset your cable or DSL modem by powering the unit off and then on. Obtain and flash the latest firmware release that is readily available on the Linksys website, www.linksys.com.

How will I be notified of new router firmware upgrades? All Linksys firmware upgrades are posted on the Linksys website at www.linksys.com, where they can be downloaded for free. The router's firmware can be upgraded with TFTP programs.

Does the Cable/DSL Wireless-Ready Router support IPSec? Yes, but only pass

through IPSec is supported.

Will the router function in a Macintosh environment? Yes, but the router’s setup pages are accessible only through Internet Explorer v4.0 or Netscape Navigator v4.0 or higher for Macintosh.

With which type of firewall is the router equipped? The Cable/DSL Wireless-

Ready Router uses NAT and TCP/IP port inspections.

Does the Router do Stateful packet inspection? No

I am not able to get the web configuration screen for the Router. What can I do?

You may have to remove the proxy settings on your Internet browser, e.g., Netscape Navigator or Internet Explorer. Or remove the dial-up settings on your browser. Check with your browser documentation.

What is DMZ? Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you want to use DMZ.

EtherFast® Cable/DSL Wireless-Ready Router with 4-Port Switch

If DMZ is used, does the exposed user share the public IP with the Router? No. Does the Router pass PPTP packets or actively route PPTP sessions? The router

allows PPTP packets to pass through.

Is the Router cross-platform compatible? Any platform that supports Ethernet and TCP/IP is compatible with the router.

Will the Router allow me to use my own public IPs and Domain, or do I have to use the IPs provided by the Router? The router mode allows for customization of

your public IPs and Domain.

How many ports can be simultaneously forwarded? Theoretically, the router can establish 520 sessions at the same time, but you can only forward 10 ranges of ports.

Does the Router replace a modem? Is there a cable or DSL modem in the Router? No, this version of the router must work in conjunction with a cable or DSL modem.

Which modems are compatible with the Router? The router is compatible with virtually any cable or DSL modem that supports Ethernet.

What are the advanced features of the Router? The router’s advanced features include Filters, Forwarding, Dynamic Routing, Static Routing, and DMZ host.

Does Linksys provide syslog support? No, Linksys does not currently provide syslog support.

How can I check whether I have static DHCP IP Addresses? Consult your ISP to

confirm the information.

How do I get mIRC to work with the Router? Set port forwarding to 113 for the computer on which you are using mIRC. If you are experiencing difficulty after setting the port forwarding, try changing the Direct Client-to-Client (DCC) settings to a range from 1024 to 1030 on the DCC option and Forwarding page of the Web-based Setup Utility.

If your questions are not addressed here, refer to the contact information on the last page of this manual.

48

49

Page 27 Page 29
Image 28
Page 27 Page 29
Contents EtherFast Cable/DSL Wireless-Ready Router With 4-Port Switch Copyright & Trademarks Table of Contents Features Linksys Cable/DSL Wireless-Ready RouterIntroduction Cable/DSL Wireless-Ready Router’s Rear Panel Package ContentsMinimum Requirements Reset Button Wireless-PC CardCable/DSL Wireless-Ready Router’s Front Panel LEDs Overview About Static & Dynamic IP AddressesConnecting Your Hardware Together and Booting Up Instant BroadbandTM Series Adding Wireless Capabilities to Your Router SetupEssid Configuring the Cable/DSL Wireless-Ready Router Instant BroadbandTM Series Quick & Easy Administration Cable/DSL Wireless-Ready Router’s Web- based UtilitySetup p Password Setting WEP Encryption Status Help Incoming/Outgoing Access Logs Here you will specify whether LogUPnP FiltersUsing IPSec Pass Through Port Forwarding PortPort Range Forwarding Dynamic Routing Static Routing DMZ Host MAC Address CloningAppendix a Troubleshooting Common Problems and SolutionsFrequently Asked Questions Through IPSec is supported Appendix B How to Obtain Your ISP’s E-mail & Web Addresses Step One Pinging an IP AddressAppendix C Installing the TCP/IP Protocol Figure C-1Appendix D Twisted-Pair Cabling Figure C-2Appendix E Glossary BlesCrimping Your Own NetworkInstant BroadbandTM Series Instant BroadbandTM Series Appendix F Specifications SpeedAppendix G Warranty Information EnvironmentalAppendix H Contact Information Copyright 2002 Linksys, All Rights Reserved

BEFSR41W specifications

The Linksys BEFSR41W is a versatile wireless broadband router that has been a popular choice for both home and small office environments since its introduction. Designed to offer reliable internet connectivity, the BEFSR41W combines wired and wireless capabilities, ensuring that users can connect multiple devices efficiently.

One of the standout features of the Linksys BEFSR41W is its integrated 4-port 10/100 Ethernet switch, which allows users to connect their wired devices directly. This is particularly useful for users who require stable connections for activities such as gaming or streaming high-definition content. The router supports the IEEE 802.3 and 802.3u standards, ensuring compatibility with a wide range of devices.

In terms of wireless capabilities, the BEFSR41W operates on the 802.11b and 802.11g standards, providing maximum wireless data rates of up to 54 Mbps. This enables users to experience reasonably fast wireless internet speeds for everyday online activities such as browsing and emailing. The router's built-in antenna offers decent coverage, making it suitable for smaller homes and office spaces.

Security is a key consideration for any network device, and the Linksys BEFSR41W incorporates several features to help safeguard users' data. It supports Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA) encryption methods, allowing users to set up secure connections and protect sensitive information from unauthorized access. Additionally, the router includes a built-in firewall to help prevent external attacks and threats.

Another significant characteristic of the BEFSR41W is its easy setup process. The router comes with a user-friendly web-based interface that simplifies the configuration process. Users can easily set up their network, configure security settings, and manage connected devices without needing specialized technical skills.

Additionally, the router is designed for longevity, with robust build quality ensuring reliability over time. It is also backward compatible with older wireless standards, which provides flexibility for users who have legacy devices in their network.

In conclusion, the Linksys BEFSR41W is a solid option for anyone seeking a dependable routing solution that balances both wired and wireless connectivity. With its blend of features, ease of use, and security options, it remains a relevant choice for users looking to establish a basic home or small office network.
Top Page Image Contents