D-Link DI-206 manual Incoming

Page 47

DI-206 ISDN Remote Router

When this is set to Out, the router will only make calls on the ISDN interface specified in the Interface field below. Also, the outgoing calls will be subject to the Name, Password and Phone Number fields in the Outgoing section below.

When set to Both, the dial in and dial out conditions described above will both be observed.

•Interface – ISDN Link 1 [ISDN L1] or ISDN Link 2 [ISDN L2]. This field is used to assign a remote network to a logical (virtual) interface called a virtual circuit. More than one remote network can be configured to use the same interface, but they cannot be connected at the same time. Thus, if you wish to have two WAN connections operate simultaneously, make sure they are configured on different interfaces. On the other hand, if you have two dial-out remote network profiles but wish to keep one line always open for dial-in users, make sure the two dial-out profiles use the same interface. In this case, the two profiles will share the same interface; the second one using it after the first one’s idle time has expired and it has relinquished it.

•Phone - This is the telephone number that will be dialed to make the outgoing connection.

•Idle Time – This is the elapsed time (in seconds), of inactivity, that will trigger the router to disconnect this interface.

•Set Peer IP as Default Gateway – When enabled, this feature sets the IP address of the remote device as the default gateway (default next hop router) for all packets not found in the routing table. This option should be enabled for the ISDN circuit (ISDN1 or ISDN2) that is used to connect to the Internet. Also, if the Peer IP is set as the default gateway here, you still need to define a static default route in the Network Configuration, IP Static Route submenu, but you don’t need to designate a gateway IP address for the static route (the routers will automatically negotiate and adjust the gateway IP setting accordingly). And also make sure that the Remote IP Address in the Remote Networks Profile is set to 0.0.0.0. Note that only one ISDN circuit should be connected to the Internet, and only one ISDN circuit (the same one) should be the default gateway.

•Incoming

•Name – The maximum length is 64 characters. This username is for password challenges (authentication). The user dialing in must supply this username in order to be allowed access to the router.

•Password – This is the password associated with the above Name field.

•Rem CLID – Remote Caller ID. This is the telephone number of the Remote User and is used for security. When a phone number is entered in this field, the router will make sure that the incoming call is coming from the same phone number as the one defined here. In other words, the remote user can only be calling from the telephone number defined here, otherwise the call will not be accepted. This function is disabled if the field is left blank.

•Call Back – This field determines whether the router calls back after receiving a call from this Remote Network Profile. If this option is enabled,

37

Page 46 Page 48
Image 47
Page 46 Page 48
Contents DI-206 Isdn Router User’s Guide Page CE Mark Warning FCC WarningSoftware Link Offices for Registration and Warranty ServiceHardware Wichtige Sicherheitshinweise Page Table of Contents Using Telnet 104 101102 Page Built-in Hub Product FeaturesEase of Installation IntroductionStandard Phone Jacks Radius Remote Authentication Dial In User ServiceDhcp Support Dynamic Host Configuration Protocol Isdn Leased LineWhat This Manual Covers Applications for your DI-206Other Resources What This Manual Doesn’t CoverPacking List Additional Installation RequirementsOrdering Your Isdn Line InstallationDI-206 Front Panel DI-206 Rear Panel Installation and Initial Configuration Telephone FeaturesConnecting the Console to the Router Setting up the ConsoleConnecting Ethernet Cables to the Router Using the ConsoleConnecting an Isdn Line to the Router Connecting a Telephone or Fax Machine to the RouterDevice Port Device Being Cable to USE Used Connected Type Important Notes on Ethernet ConnectionsInitial Configuration of the Router Powering Up Devices for Initial ConfigurationConfiguring the LAN Port From the Main Menu choose Advanced Functions Choose Interface Configuration, LANChoose Network Configuration, IP Configuration Plugging in All Devices Console Program Main Menu Configuration and ManagementSystem Information Interface Configuration LAN DI-206 Isdn Remote Router Network Configuration IP Stack Configuration DI-206 Isdn Remote Router DI-206 Isdn Remote Router IP Static Route Examples IP Static RouteRouter Advertisement Snmp Agent ConfigurationIP Networking Snmp Community Configuration Snmp Authenticated Trap Snmp Trap Manager ConfigurationRemote Operation Overview Remote Access ConfigurationAdvanced Functions Remote Network Connections DI-206 Isdn Remote Router Dial Configuration Dial-In User Profile DI-206 Isdn Remote Router Remote Network Profile Phone Number Supplied by Toggle between Router and CallerDI-206 Isdn Remote Router Incoming Outgoing Dhcp ConfigurationDynamic IP Pool Dhcp Server ConfigurationDI-206 Isdn Remote Router Static IP Pool Dhcp Relay Agent Filter ConfigurationFilter State of Interface Configuring a Filter SetLayer 2 Filter IP Filter DI-206 Isdn Remote Router Multiple Home Configuration DI-206 Isdn Remote Router Static ARP NAT Configuration How NAT Works NAT Setting Local IP Addresses Configure NAT/NAPT DI-206 Isdn Remote Router Dynamic NAT Static NAT Dynamic NaptStatic Napt Configure Napt for Special ApsDI-206 Isdn Remote Router Telnet/Discovery Enable DNS Configuration Host Table Multi-Link PPP Configuration Radius ConfigurationDI-206 Isdn Remote Router Admin Configuration System Status System MaintenanceLAN Counter Table StatisticsCounter DI-206 Isdn Remote Router Isdn Counter Table Runtime Tables IP Routing Table PPP Table ARP TableLog and Trace Event/Error LogLog Configuration View Log File Trace Buffer Trace Buffer ConfigurationPacket Triggered Last Call View Trace BufferConnection Test DiagnosticLoopback Test Ping TestSystem LAN System Isdn Software UpdateSystem Restart System Settings Backup/Restore Factory ResetRestore System Settings Backup System SettingsDI-206 Isdn Remote Router System Configuration Prom System ConfigurationSystem Reset TCP/IP Parameters ConfigurationSoftware Update Execute Bootload Eeprom Factory ResetDI-206 Isdn Remote Router Using Telnet via Isdn Using TelnetTelnet Configuration Using Telnet via LANSystem Timeout Configuring the DI-206 for Radius Authentication Using Radius AuthenticationInstalling a Radius Server Adding Users to the Radius Database Problems with the LAN Interface Appendix a TroubleshootingSome Common Problems With the DI-206 Problems With the Isdn LineDI-206 Isdn Remote Router IP Network Classes Appendix B IP ConceptsIP Addresses Subnet Mask IP Port Numbers Appendix C IP Protocol and Port NumbersIP Protocol Numbers General Appendix D Technical SpecificationsPhysical & Environmental Appendix E Country ID Numbers Configuration File Example Appendix F Configuration File103 BAP IndexSee LAN Snmp Offices Registration Card

DI-206 specifications

The D-Link DI-206 is a versatile and reliable networking solution designed to cater to the demands of both home and small office environments. This router is equipped with a range of features and technologies that ensure efficient connectivity and seamless online experiences.

One of the key highlights of the D-Link DI-206 is its robust and user-friendly interface, which is ideal for users of all technical levels. It offers an easy setup process, typically involving a simple web-based configuration that allows users to get their network up and running in no time. The device supports multiple operating modes, including router and access point modes, making it flexible and adaptable to varying networking requirements.

The DI-206 is equipped with dual WAN ports, which provide users with the ability to connect to two separate internet connections. This feature enhances reliability and ensures continuous internet access, as it can automatically switch to a backup connection if the primary line fails. Such redundancy is particularly advantageous for businesses that require uninterrupted connectivity for operations.

In terms of performance, the D-Link DI-206 supports advanced wireless standards, offering data transfer rates that cater to modern bandwidth needs. With dual-band capabilities, it can operate on both 2.4GHz and 5GHz frequencies, allowing users to maximize their wireless coverage while minimizing interference from other devices. This is essential for activities such as streaming, gaming, and video conferencing, where bandwidth demands can be high.

Security is another critical aspect of the D-Link DI-206. It incorporates comprehensive security features, including WPA/WPA2 encryption to protect user data from unauthorized access. Additionally, the router features a built-in firewall and supports VPN passthrough, providing an extra layer of security for users engaging in sensitive online activities.

The DI-206 also offers multiple Ethernet ports for wired connections, enabling users to connect various devices such as computers, printers, and gaming consoles directly to the network. This ensures stable and high-speed internet access for devices that require a consistent connection.

Overall, the D-Link DI-206 stands out as a reliable networking device that combines performance, versatility, and security. Whether for home use or small office environments, it provides an effective solution for users looking to establish a strong and secure network. With its range of features and technologies, the DI-206 is a compelling option for those seeking to enhance their online connectivity and overall experience.
Top Page Image Contents