Linksys la), wag300n (eu manual Advanced Routing Tab

Page 25

Wireless-N ADSL2+ Gateway

The Advanced Routing Tab

The Advanced Routing screen allows you to configure the NAT, dynamic routing, and static routing settings.

Advanced Routing

•Operating Mode. In this section, you will configure the Gateway’s general routing settings.

•NAT. NAT is a security feature that is enabled by default. It enables the Gateway to translate IP addresses of your local area network to a different IP address for the Internet. To disable NAT, click the Disabled radio button.

•Dynamic Routing. With Dynamic Routing you can enable the Gateway to automatically adjust to physical changes in the network’s layout. Using RIP, the Gateway determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other Gateways on the network.

•RIP. If you have multiple routers, you may want to use the Routing Information Protocol (RIP) so the routers can exchange routing information with each other. To use RIP, select the Enabled radio button. Otherwise, keep the default, Disabled.

•RIP Version. Select the protocol version you want, RIP1 or RIPv2.

•Static Routing. If the Gateway is connected to more than one network, it may be necessary to set up a static route between them. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. To create a static route, change the following settings:

•Select set number. Select the number of the static route from the drop-down menu. The Gateway supports up to 20 static route entries. If you need to delete a route, then select the entry and click the Delete This Entry button.

•Destination IP Address. The Destination IP Address is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route. If you are building a route to an entire network, be sure that the network portion of the IP address is set to 0.

•Subnet Mask. Enter the Subnet Mask (also known as the Network Mask), which determines which portion of an IP address is the network portion, and which portion is the host portion.

•Gateway. Enter the IP address of the gateway device that allows for contact between the Gateway and the remote network or host.

Chapter 5: Configuring the Wireless-N ADSL2+ Gateway

Figure 5-11: Advanced Routing

19

The Setup Tab

Page 24 Page 26
Image 25
Page 24 Page 26
Contents GHz Copyright and Trademarks How to Use this GuideWord definition Table of Contents Wireless-N ADSL2+ Gateway Network Ports and Reset Button on Side Panel25 Internet Access Policy Welcome IntroductionWhat’s in this User Guide? Wireless-N ADSL2+ Gateway Gateway’s Functions Planning Your NetworkIP Addresses What’s an IP Address?Dynamic IP Addresses Dhcp Dynamic Host Configuration Protocol ServersPorts and Reset Button on Side Panel GettingtoKnowtheWireless-NADSL2+GatewayLEDs on Side Panel WirelessWired Connection to a Computer Connecting the Wireless-N ADSL2+ GatewayOverview Connect the Power Wireless Connection to a ComputerSetup Configuring the Wireless-N ADSL2+ GatewayWireless Administration Access RestrictionsSecurity Applications & GamingSetup Tab How to Access the Web-based UtilityBasic Setup Tab Internet SetupStatic IP RFC 1483 Bridged Dynamic IPIPoA RFC 1483 RoutedRFC 2364 PPPoA RFC 2516 PPPoEOptional Settings required by some ISPs Bridge Mode OnlyNetwork Setup Configuring the Wireless-N ADSL2+ Gateway Setup Tab DynDNS.org Ddns TabTZO.com Advanced Routing Advanced Routing Tab12 Routing Table Basic Wireless Settings Tab Wireless TabWireless Network PSK-Personal Wireless Security TabPSK2-Personal PSK2-Enterprise PSK-EnterpriseRadius WEP Wireless MAC Filter Wireless MAC Filter TabAdvanced Wireless Advanced Wireless Settings TabConfiguring the Wireless-N ADSL2+ Gateway Wireless Tab Firewall Tab Security TabFirewall VPN Passthrough VPN Passthrough TabInternet Access Policy Tab Access Restrictions TabInternet Access Policy 27 List of PCs Single Port Range Forwarding Tab Applications and Gaming TabSingle Port Forwarding Port Range Forwarding Port Range Forwarding TabPort Range Triggering Port Triggering TabDMZ DMZ TabQoS Tab QoS Quality of Service33 QoS Online Game Remove SummaryGateway Access Administration TabManagement Tab Wlan UPnPReporting Reporting TabEmail Alerts Ping Test Diagnostics TabBackup Configuration Backup & Restore TabRestore Configuration Firmware Upgrade Tab Factory Defaults TabFactory Defaults Firmware UpgradeGateway Tab Status TabGateway Information Internet ConnectionLocal Network Local Network Tab52 Wireless DSL Status DSL Connection TabPVC Connection Common Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a computer Want to test my Internet connection Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway TCP Application Start and End Protocol IP Address EnableCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Gateway to factory defaultFirmware upgrade failed, and/or the Power LED is flashing Power LED flashes continuously My DSL service’s PPPoE is always disconnectingWhere is the Gateway installed on the network? Frequently Asked QuestionsIs IPSec Passthrough supported by the Gateway? Does the Gateway support ICQ send file? Does the Gateway support IPX or AppleTalk?What is DMZ Hosting? What is the Ieee 802.11g standard? What are the advanced features of the Gateway?Is the Gateway cross-platform compatible? How many ports can be simultaneously forwarded?What Ieee 802.11b and 802.11g features are supported? What is the Ieee 802.11b standard?What is ad-hoc mode? What is infrastructure mode?What is Spread Spectrum? What is the ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP?How do I resolve issues with signal loss? How do I reset the Gateway?Have excellent signal strength, but I cannot see my network Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-N ADSL2+ Gateway Windows 98 or Me Instructions Figure C-1 IP Configuration ScreenFigure C-3 MAC Address/Physical Address Windows 2000 or XP InstructionsAppendix D Upgrading Firmware Figure D-1 Firmware UpgradeAppendix E Glossary Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Appendix F Specifications Ssid Broadcast Disable ToD filter Blocks Access by TimeAccess restriction by MAC and IP addresses VPN Passthrough for IPSec, PPTP, and L2TP ProtocolsAppendix G Warranty Information FCC Statement Appendix H Regulatory InformationDual-Band Wireless Access Point Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Location Frequency Range MHz Power Eirp Applicable Power Levels in FranceOpen the Wireless Network Connection window Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Europe Mail Address Appendix I Contact InformationOutside of Europe Mail Address
Top Page Image Contents