Linksys WAG300N manual Connecting the Wireless-N ADSL2+ Gateway, Overview

Page 14

Wireless-N ADSL2+ Gateway

Chapter 4: Connecting the Wireless-N ADSL2+ Gateway

Overview

The installation technician from your ISP should have left the setup information with you after installing your broadband connection. If not, you can call your ISP to request that data. After you have the setup information you need for your specific type of Internet connection, you can begin installation and setup of the Gateway.

To use a computer with an Ethernet adapter to configure the Gateway, continue to “Wired Connection to a Computer.” To use a wireless-equipped computer, continue to “Wireless Connection to a Computer.”

Wired Connection to a Computer

1.Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.

2.Connect a phone cable from the DSL port on the Gateway’s side panel to the wall jack of the ADSL line. A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions.

NOTE: A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions.

3.Connect one end of an Ethernet network cable to one of the Ethernet ports (labeled 1-4) on the back of the Gateway, and the other end to an Ethernet port on a computer. Repeat this step to connect more computers, a switch, or other network devices to the Gateway.

4.Connect the power adapter to the Gateway’s Power port, and then plug the power adapter into a power outlet.

NOTE: You should always plug the Gateway’s power adapter into a power strip with surge protection.

The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The Power LED will flash for a few seconds, and then it will be solidly lit when the self-test is complete. If the LED flashes for one minute or longer, see “Appendix A: Troubleshooting.”

5. Power on one of your computers that is connected to the Gateway.

Figure 4-1: Connect the ADSL Line

Figure 4-2: Connect a PC

Figure 4-3: Connect the Power

Go to “Chapter 5: Configuring the Wireless-N ADSL2+ Gateway.”

Chapter 4: Connecting the Wireless-N ADSL2+ Gateway

8

Overview

Image 14
Contents GHz Word definition How to Use this GuideCopyright and Trademarks Table of Contents Wireless-N ADSL2+ Gateway Ports and Reset Button on Side Panel Network25 Internet Access Policy Introduction WelcomeWhat’s in this User Guide? Wireless-N ADSL2+ Gateway IP Addresses Planning Your NetworkGateway’s Functions What’s an IP Address?Dhcp Dynamic Host Configuration Protocol Servers Dynamic IP AddressesGettingtoKnowtheWireless-NADSL2+Gateway Ports and Reset Button on Side PanelWireless LEDs on Side PanelOverview Connecting the Wireless-N ADSL2+ GatewayWired Connection to a Computer Wireless Connection to a Computer Connect the PowerWireless Configuring the Wireless-N ADSL2+ GatewaySetup Security Access RestrictionsAdministration Applications & GamingBasic Setup Tab How to Access the Web-based UtilitySetup Tab Internet SetupRFC 1483 Bridged Dynamic IP Static IPRFC 1483 Routed IPoARFC 2516 PPPoE RFC 2364 PPPoANetwork Setup Bridge Mode OnlyOptional Settings required by some ISPs Configuring the Wireless-N ADSL2+ Gateway Setup Tab TZO.com Ddns TabDynDNS.org Advanced Routing Tab Advanced Routing12 Routing Table Wireless Network Wireless TabBasic Wireless Settings Tab WPA2-Personal Wireless Security TabWPA-Personal WPA-Enterprise WPA2-EnterpriseRadius WEP Wireless MAC Filter Tab Wireless MAC FilterAdvanced Wireless Settings Tab Advanced WirelessConfiguring the Wireless-N ADSL2+ Gateway Wireless Tab Firewall Security TabFirewall Tab VPN Passthrough Tab VPN PassthroughInternet Access Policy Access Restrictions TabInternet Access Policy Tab 27 List of PCs Single Port Forwarding Applications and Gaming TabSingle Port Range Forwarding Tab Port Range Forwarding Tab Port Range ForwardingPort Triggering Tab Port Range TriggeringDMZ Tab DMZQoS Quality of Service QoS Tab33 QoS Online Game Summary RemoveManagement Tab Administration TabGateway Access UPnP WlanEmail Alerts Reporting TabReporting Diagnostics Tab Ping TestRestore Configuration Backup & Restore TabBackup Configuration Factory Defaults Factory Defaults TabFirmware Upgrade Tab Firmware UpgradeGateway Information Status TabGateway Tab Internet ConnectionLocal Network Tab Local Network52 Wireless PVC Connection DSL Connection TabDSL Status Need to set a static IP address on a computer Appendix a TroubleshootingCommon Problems and Solutions Want to test my Internet connection Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Application Start and End Protocol IP Address Enable TCPCan’t get the Internet game, server, or application to work Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Gateway to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnecting Power LED flashes continuouslyIs IPSec Passthrough supported by the Gateway? Frequently Asked QuestionsWhere is the Gateway installed on the network? Does the Gateway support IPX or AppleTalk? Does the Gateway support ICQ send file?What is DMZ Hosting? Is the Gateway cross-platform compatible? What are the advanced features of the Gateway?What is the Ieee 802.11g standard? How many ports can be simultaneously forwarded?What is ad-hoc mode? What is the Ieee 802.11b standard?What Ieee 802.11b and 802.11g features are supported? What is infrastructure mode?What is DSSS? What is FHSS? And what are their differences? What is the ISM band?What is Spread Spectrum? What is WEP?Have excellent signal strength, but I cannot see my network How do I reset the Gateway?How do I resolve issues with signal loss? Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-N ADSL2+ Gateway Figure C-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions Figure C-3 MAC Address/Physical AddressFigure D-1 Firmware Upgrade Appendix D Upgrading FirmwareAppendix E Glossary Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Appendix F Specifications Access restriction by MAC and IP addresses ToD filter Blocks Access by TimeSsid Broadcast Disable VPN Passthrough for IPSec, PPTP, and L2TP ProtocolsAppendix G Warranty Information Appendix H Regulatory Information FCC StatementDual-Band Wireless Access Point Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Applicable Power Levels in France Location Frequency Range MHz Power EirpOpen the Wireless Network Connection window Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Appendix I Contact Information Europe Mail AddressOutside of Europe Mail Address

WAG300N specifications

The Linksys WAG300N is a highly versatile wireless modem router, designed to meet the needs of both home and small office environments. This device combines multiple functionalities, featuring a Wireless-N access point, a 4-port Ethernet switch, and an integrated DSL modem. Its compatibility with ADSL2+ standards allows for seamless internet connectivity, ensuring that users can experience high-speed internet up to 24 Mbps, depending on their DSL connection.

One of the defining characteristics of the WAG300N is its support for the IEEE 802.11n wireless standard, which provides significantly improved data transfer rates over its predecessors. This technology allows for speeds of up to 300 Mbps, making it suitable for bandwidth-intensive applications such as streaming high-definition videos, online gaming, and large file downloads. The router's MIMO (Multiple Input Multiple Output) technology enhances wireless coverage, enabling connections at greater distances and through obstacles like walls.

Security is a key concern for Linksys, and the WAG300N addresses this with a variety of robust features. It supports WPA, WPA2, and WEP encryption for secure wireless connection and includes a built-in firewall to protect the network from unwanted intrusions. Parental controls are also available, allowing users to manage internet access, ensuring a safer online environment for children.

The Linksys WAG300N is easy to set up and manage thanks to its web-based interface. Users can quickly configure the device using the installation CD or through a straightforward online setup wizard. Furthermore, firmware updates can be performed easily, allowing users to keep their devices secure and up to date with the latest features.

In terms of design, the WAG300N boasts a sleek black casing with LED indicators for power, internet connectivity, and wireless activity, enabling users to monitor device status at a glance. Its compact size ensures it does not occupy excessive space, making it an attractive addition to any office or home environment.

Overall, the Linksys WAG300N is a powerful networking device that offers great performance, advanced security features, and ease of use, making it an excellent choice for users looking to enhance their internet connectivity experience. Whether for casual browsing or resource-intensive tasks, the WAG300N stands out with its blend of speed, reliability, and versatility.