Linksys WAG300N manual Wireless Connection to a Computer, Connect the Power

Page 15

Wireless-N ADSL2+ Gateway

Wireless Connection to a Computer

If you want to use a wireless connection to access the Gateway, follow these instructions:

1.Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.

2.Connect a phone cable from the DSL port on the Gateway’s back panel to the wall jack of the ADSL line. A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions.

NOTE: A small device called a microfilter (not included) may be necessary between each phone and wall jack to prevent interference. Contact your ISP if you have any questions.

3. Connect the power adapter to the Power port, and then plug the power adapter into a power outlet.

NOTE: You should always plug the Gateway’s power adapter into a power strip with surge protection.

The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The Power LED will flash for a few seconds, and then it will be solidly lit when the self-test is complete. If the LED flashes for one minute or longer, see “Appendix A: Troubleshooting.”

4.Power on one of the computers on your wireless network(s).

5.For initial access to the Gateway through a wireless connection, make sure the computer’s wireless adapter has its SSID set to linksys (the Gateway’s default setting), and its wireless security is disabled. After you have accessed the Gateway, you can change the Gateway and this computer’s adapter settings to match your usual network settings.

Go to “Chapter 5: Configuring the Wireless-N ADSL2+ Gateway.”

Chapter 4: Connecting the Wireless-N ADSL2+ Gateway

Figure 4-4: Connect the ADSL Line

Figure 4-5: Connect the Power

NOTE: You should always change the SSID from its default, linksys, and enable wireless security.

9

Wireless Connection to a Computer

Image 15
Contents GHz How to Use this Guide Copyright and TrademarksWord definition Table of Contents Wireless-N ADSL2+ Gateway Network Ports and Reset Button on Side Panel25 Internet Access Policy Welcome IntroductionWhat’s in this User Guide? Wireless-N ADSL2+ Gateway What’s an IP Address? Planning Your NetworkGateway’s Functions IP AddressesDynamic IP Addresses Dhcp Dynamic Host Configuration Protocol ServersPorts and Reset Button on Side Panel GettingtoKnowtheWireless-NADSL2+GatewayLEDs on Side Panel WirelessConnecting the Wireless-N ADSL2+ Gateway Wired Connection to a ComputerOverview Connect the Power Wireless Connection to a ComputerConfiguring the Wireless-N ADSL2+ Gateway SetupWireless Applications & Gaming Access RestrictionsAdministration SecurityInternet Setup How to Access the Web-based UtilitySetup Tab Basic Setup TabStatic IP RFC 1483 Bridged Dynamic IPIPoA RFC 1483 RoutedRFC 2364 PPPoA RFC 2516 PPPoEBridge Mode Only Optional Settings required by some ISPsNetwork Setup Configuring the Wireless-N ADSL2+ Gateway Setup Tab Ddns Tab DynDNS.orgTZO.com Advanced Routing Advanced Routing Tab12 Routing Table Wireless Tab Basic Wireless Settings TabWireless Network Wireless Security Tab WPA-PersonalWPA2-Personal WPA2-Enterprise WPA-EnterpriseRadius WEP Wireless MAC Filter Wireless MAC Filter TabAdvanced Wireless Advanced Wireless Settings TabConfiguring the Wireless-N ADSL2+ Gateway Wireless Tab Security Tab Firewall TabFirewall VPN Passthrough VPN Passthrough TabAccess Restrictions Tab Internet Access Policy TabInternet Access Policy 27 List of PCs Applications and Gaming Tab Single Port Range Forwarding TabSingle Port Forwarding Port Range Forwarding Port Range Forwarding TabPort Range Triggering Port Triggering TabDMZ DMZ TabQoS Tab QoS Quality of Service33 QoS Online Game Remove SummaryAdministration Tab Gateway AccessManagement Tab Wlan UPnPReporting Tab ReportingEmail Alerts Ping Test Diagnostics TabBackup & Restore Tab Backup ConfigurationRestore Configuration Firmware Upgrade Factory Defaults TabFirmware Upgrade Tab Factory DefaultsInternet Connection Status TabGateway Tab Gateway InformationLocal Network Local Network Tab52 Wireless DSL Connection Tab DSL StatusPVC Connection Appendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a computer Want to test my Internet connection Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway TCP Application Start and End Protocol IP Address EnableCan’t get the Internet game, server, or application to work To start over, I need to set the Gateway to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing Power LED flashes continuously My DSL service’s PPPoE is always disconnectingFrequently Asked Questions Where is the Gateway installed on the network?Is IPSec Passthrough supported by the Gateway? Does the Gateway support ICQ send file? Does the Gateway support IPX or AppleTalk?What is DMZ Hosting? How many ports can be simultaneously forwarded? What are the advanced features of the Gateway?What is the Ieee 802.11g standard? Is the Gateway cross-platform compatible?What is infrastructure mode? What is the Ieee 802.11b standard?What Ieee 802.11b and 802.11g features are supported? What is ad-hoc mode?What is WEP? What is the ISM band?What is Spread Spectrum? What is DSSS? What is FHSS? And what are their differences?How do I reset the Gateway? How do I resolve issues with signal loss?Have excellent signal strength, but I cannot see my network Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-N ADSL2+ Gateway Windows 98 or Me Instructions Figure C-1 IP Configuration ScreenFigure C-3 MAC Address/Physical Address Windows 2000 or XP InstructionsAppendix D Upgrading Firmware Figure D-1 Firmware UpgradeAppendix E Glossary Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Appendix F Specifications VPN Passthrough for IPSec, PPTP, and L2TP Protocols ToD filter Blocks Access by TimeSsid Broadcast Disable Access restriction by MAC and IP addressesAppendix G Warranty Information FCC Statement Appendix H Regulatory InformationDual-Band Wireless Access Point Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Location Frequency Range MHz Power Eirp Applicable Power Levels in FranceOpen the Wireless Network Connection window Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Wireless-N ADSL2+ Gateway Europe Mail Address Appendix I Contact InformationOutside of Europe Mail Address

WAG300N specifications

The Linksys WAG300N is a highly versatile wireless modem router, designed to meet the needs of both home and small office environments. This device combines multiple functionalities, featuring a Wireless-N access point, a 4-port Ethernet switch, and an integrated DSL modem. Its compatibility with ADSL2+ standards allows for seamless internet connectivity, ensuring that users can experience high-speed internet up to 24 Mbps, depending on their DSL connection.

One of the defining characteristics of the WAG300N is its support for the IEEE 802.11n wireless standard, which provides significantly improved data transfer rates over its predecessors. This technology allows for speeds of up to 300 Mbps, making it suitable for bandwidth-intensive applications such as streaming high-definition videos, online gaming, and large file downloads. The router's MIMO (Multiple Input Multiple Output) technology enhances wireless coverage, enabling connections at greater distances and through obstacles like walls.

Security is a key concern for Linksys, and the WAG300N addresses this with a variety of robust features. It supports WPA, WPA2, and WEP encryption for secure wireless connection and includes a built-in firewall to protect the network from unwanted intrusions. Parental controls are also available, allowing users to manage internet access, ensuring a safer online environment for children.

The Linksys WAG300N is easy to set up and manage thanks to its web-based interface. Users can quickly configure the device using the installation CD or through a straightforward online setup wizard. Furthermore, firmware updates can be performed easily, allowing users to keep their devices secure and up to date with the latest features.

In terms of design, the WAG300N boasts a sleek black casing with LED indicators for power, internet connectivity, and wireless activity, enabling users to monitor device status at a glance. Its compact size ensures it does not occupy excessive space, making it an attractive addition to any office or home environment.

Overall, the Linksys WAG300N is a powerful networking device that offers great performance, advanced security features, and ease of use, making it an excellent choice for users looking to enhance their internet connectivity experience. Whether for casual browsing or resource-intensive tasks, the WAG300N stands out with its blend of speed, reliability, and versatility.