3Com 3C13701 3C13751 3C13755 3C13759 3C13840 3C13880 Router 4-Port CE1/PRI FIC, Connector DB-25

Page 137

3Com Router 5000 and Router 6000 v2.41

Module Guide

Chapter 4 Flexible Interface Cards (Router 6000)

 

 

 

 

 

Caution:

Before connecting an FIC card, identify the type of the equipment to be connected (that is, the synchronous/asynchronous mode, DTE/DCE mode, and so on), signaling criterion required by the access equipment, baud rate, and line clock.

Step 1: Identify type of the interface to be connected and then choose the correct synchronous/asynchronous serial interface cable.

Step 2: Plug the DB-28 connector of the cable to the corresponding DB-28 port on the FIC-SAE card.

Step 3: Connect the other end of the cable as follows:

z

z

If the WAN is a DDN line, connect the cable to the port on the CSU/DSU.

If the WAN is a dialup line, connect the cable to the serial port of an analog modem.

Step 4: Power on the router, and check behavior of the LINK LED on the FIC-SAE panel. It is OFF when fault occurs on the line and signal is not synchronized. Check the line status.

4.7 Router 4-Port CE1/PRI FIC

4.7.1Introduction

I.Router 4-Port CE1/PRI FIC

Router 4-Port CE1/PRI FIC, the 4-port channelized E1/PRI interface card, transmits, receives, and processes E1 data traffic. In addition, you can use the card for other purposes, such as CE1 access and the ISDN PRI function.

4.7.2Interface Attributes

The following table describes the interface attributes of the FIC-E1 and FIC-E1-F cards.

Table 4-14Interface attributes of the FIC-E1 and FIC-E1-F cards

 

 

 

 

Description

 

Attribute

 

 

 

 

 

 

 

 

Router 4-Port CE1/PRI

 

 

 

 

 

 

 

 

 

 

FIC

 

 

 

 

 

 

 

Connector

 

 

DB-25

 

 

 

 

 

 

4-21

Page 136 Page 138
Image 137
Page 136 Page 138
Contents 3C13701 3C13751 3C13755 3C13759 3C13840 3C13880 3Com Router 5000 Family Router 6000 Family Module Guide3Com Corporation Campus Drive Marlborough, MA 01752-3064 Table of Contents Router 2-Port FXS/FXO/E&M MIM Modules 3Com Router 5000 and Router 6000 Module Guide 3Com Router 5000 and Router 6000 Module Guide Table of Contents Interface LEDs Interface Cable 3Com Router 5000 and Router 6000 Module Guide Vii 3Com Router 5000 and Router 6000 Module Guide Types of MIMs Types of SICsTypes of FICs SIC/MIM Purchasing Guideline Installation/Removal of SIC and MIMIII. Installing SIC Installing/Removing SICTools required II. Removing blank filler panel from SIC slotIV. Removing SIC Installing/Removing MIMII. Installing MIM III. Removing MIM Installing/Removing an FICTroubleshooting Attribute Router 1-Port 10/100 SIC Router 1-Port 10/100 SICInterface Attributes Interface Cable Connecting the Interface CableIntroduction Router 1-Port Serial SICSynchronous and asynchronous 24 RS232 Maximum Baud rate bps Transmission Distance mII. DTE and DCE AppearanceEquipment type Interface type Typical equipment DTEDTE, DCE Attribute Description Synchronous AsynchronousInterface LEDs 5V.24 RS232 DTE cable 24 RS232 DCE cable 7V.35 DTE cable 35 DCE cable Connecting Interface Cable9Router 2-Port ISDN-S/T SIC Router 2-Port ISDN-S/T SIC and Router 2-Port ISDN-U SICIsdn Attribute DescriptionLED Connecting Interface Cable 13Router 1-Port Fractional E1 SIC Router 1-Port Fractional E1 SICDIP Switch DIP switch Description Ohm Ohm impedance Impedance 8BIT Module GuideOt-s h rink able tu be Pos.15 Connecting Interface Cable BNC 20Router 1-Port Fractional T1 SIC Router 1-Port Fractional T1 SIC12Interface attributes of Router 1-Port Fractional T1 SIC 22 T1 cable Router 1-Port Analog Modem SIC Attribute Description Connector type RJ11Blinking means the connection is being set up Connecting Interface Cable 25Router 1-Port FXS/FXO SIC Router 2-Port FXS/FXO SIC 27Router 1-Port FXS SIC panel 29Router 2-Port FXS SIC panel Router 1-Port SAE SIC 31Router 1-Port SAE SIC panel 32V24 DTE cable 24 DCE cable 33V.24 DCE cable 35 DTE cable 37X.21 DCE cable RS449 DTE cable RS530 DCE cable Router 2-Port FXS/FXO/E&M MIM module Multifunctional Interface Modules Router1Router 2-Port FXS/FXO/E&M MIM MOdule II. Router 4-Port FXS/FXO/E&M MIM module3Router 2-Port FXS panel 7Router 4-Port FXO panel Interface cable of FXS/FXO modulesPBX II. Interface cable of E&M modulesRING0 RING1 TIP1 TIP0 Router E1 Voice Module Isdn PRI 11Router E1Voice ModuleActive Connecting Interface Cable Router T1 Voice Module CT1 16Router T1Voice ModuleReceived or/and transmitted T1VI cable 20 Ndec Ndec ModuleDeny RUNSpeed Troubleshooting Attribute Description Router 2-Port 10/100 MIM Router 2-Port 10/100 MIMII. Making Ethernet cables Ethernet cableRouter 4-Port Serial MIM Module 24 RS232 Baud rate bps Maximum transmission Distance m Bps II. Introduction to DTE and DCEDTE DCE Router 4-Port Serial MIM interface cable DB100 male DTE and DCE Connecting interface cable of Router 4-Port Serial MIMRouter 2 and 4-Port Enhanced Serial MIM Interface Attributes Following figures show the 2 and 4-port panels 26 2-port panel 28V24 DTE cable 24 DCE cable 32X.21 DTE cable 21 DCE cable 36RS530 DTE cable RS530 DCE cable Attribute Description Port module Router 2 and 4-Port CE1/PRI MIM Modules4-Port CE1/PRI 38 2-port panel 412-port 120-ohm balanced twisted pair cable Interface cable of 2-port modulesII. Conversion cable for 4-port module 42120-ohm 4-port module conversion cable Internal DIP Switches 8BIT 3BIT OFF 4BIT 5BIT45Extending an 75-ohm unbalanced coaxial cable Connecting interface cable of 1E1/2E1 and modulesII. Connecting interface cable of 4-port Router 4-Port ISDN-S/T MIM Module DIP switch Description Default Setting 49ISDN S/T cable Router 2-Port CT1/PRI MIMmodule Router 2-Port CT1/PRI MIMLP/AL LINK/ACT51 T1 cable Router 1-Port Adsl Over Pots MIM Attribute Router 1-Port Adsl Over Panel and Interface LEDPots MIM 29LEDs on the Router 1-Port Adsl Over Pots MIM panel Router 2-Port Adsl Over Router 2-Port Adsl Over Pots MIMAttribute Panel and Interface LED Router NDEC2 Encryption Accelerator MIM 56Connecting the Router 2-Port Adsl Over Pots MIM57Router NDEC2 Encryption Accelerator MIM Feature DescriptionStatus IndicationE1 IMA MIM Router 4-Port E1 IMA MIMAppearance of the Interface Card AAL5 Panels and Interface LEDsMeaning Connection of the Interface CableRouter 4-Port T1 IMA MIM Router 4-Port T1 IMA MIMIntroduction to the Interface card OFF the link is disconnected SMB Router 1-Port CE3 MIM Module65 E3/T3 cable Router 1-Port CT3 MIM Module Router 1-Port CT3 MIM panel is shown in the following figure MDI/MDIX Router 1-Port 10/100/1000 MIMAttribute Router 1-Port 10/100/1000 MIM 68Ethernet cable Attribute Description Router 2-Port 10/100 Router 2-Port 10/100 FICPanel and Interface LEDs 2Ethernet cable Router 1-Port 100FX MM FIC/100FX SM FIC Attribute Description 100FX SM 100FX MM Attribute Description 100FX SM 100FX MM EthernetSNAP Interface Optical FiberConnecting the Interface Optical Fiber Attribute Port 10/100/1000 FIC Router 1-Port 10/100/1000 FIC7Ethernet cable Attribute Port Gigabit Ethernet FIC Router 1-Port Gigabit Ethernet Fiber FICOFF means no link is present on means a link is present 1-Port GEF FIC Connecting the Interface Optic FiberSFP Attribute Port GEF FICInterface Cable Router 4-Port/8-Port Enhanced Serial FIC 3Com Router 5000 and Router 6000 Module Guide Interface Attributes Panel and Interface LEDs 14V24 DTE cable 24 DCE cable 17V.35 DCE cable 21 DTE cable 21RS449 DCE cable RS530 DTE cable Router 4-Port CE1/PRI FIC Connector DB-25Router 4-Port CE1/PRI FIC Attribute Router 4-Port CE1/PRIOFF means no link is present on means a link is present Description Attribute Router 4-Port CE1/PRIInterface cable of the Router 4-Port CE1/PRI FIC 27120-ohm 4E1 adapter cable II. Interface cable of the Router 4-Port CE1/PRI FICCard Router 4-Port CE1/PRI FIC Internal DIP Switch29Extending an E1 75-ohm unbalanced coaxial cable DB-15 RJ-45 Network Router II. Router 4-Port Fractional T1 FIC Router 4-Port CT1/PRI FIC32 T1 cable RJ-45 Straight-through cable CE3 Router 1-Port CE3 FICSMB 35 E3/T3 cable Router 1-Port CT3 FIC CT3 Attribute Router 1-Port E3 ATM FIC 11 8.8 Router 1-Port E3 ATM FIC38 E3/T3 cable Router 1-Port T3 ATM FIC Color State Attribute Router 1-Port T3 ATM FICLP/ALM LOSInterface Cable Attribute Router 1-Port OC-3 Fiber-optic Connector Number ConnectorsLED Sonet OC-3/SDH STM-1Yellow Solid Blinking Off Alarms Detected Layer Alarm TypeLOL, LOS, OOF, LOF LOP, AIS, RDI, REIAttribute Router 1-Port Adsl FIC Router 2-Port Adsl FIC Router 1/2-Port Adsl FICSupported service Adsl over the regular telephone line Router 1-Port Adsl FIC/Router 2-Port Adsl FIC 45Connecting the Router 1/2-Port Adsl FICInterface Attributes 48Connect the FIC Description Attribute Router 4-Port Router 4-Port E1 IMA FIC75-ohm 75-ohm 120-ohm50 75-ohm panel 5175-ohm 8E1 conversion cable Attribute Description Router 4-Port T1 IMA FIC Router 4-Port T1 IMA FICRouter 1-Port OC3 POS FIC SFP/LC Attribute Router 1-Port OC3 POS FICColor State LOP, AIS, RDI LOS, LOF, OOFAIS, RDI Following figure illustrates the 2-Port FXS panel OFF means that no link is present on means a link is present Router 1-Port E1 Voice FIC CE1 42LEDs on the Router 1-Port E1 Voice FIC panel Connecting the Interface Cable Router 1-Port T1 Voice FIC 64 T1VI cable Router NDEC2 Encryption Accelerator FIC Interface FeaturesPanel and LEDs Incorrect LED Reason Action to take Behaviors 23 RPU2 Encryption AcceleratorStatus LED Active LEDSpecifications SpecificationsLED and button LED and button DescriptionInterface ResetEncryption daughter card PWR1Attribute Description
Related manuals
Manual 94 pages 1.76 Kb

3C13751, 3C13701, 3C13840, 3C13759, 3C13880 specifications

The 3Com 3C13880 and 3C13840 are notable components within the realm of networking technology, primarily designed for enterprise-grade solutions. These devices belong to the 3Com family, which has long been recognized for its commitment to developing robust networking products tailored to facilitate efficient data transfers and improve connectivity across various platforms.

One of the standout features of the 3C13880 is its high-performance capabilities. This model supports advanced functions such as load balancing and fault tolerance, critical for maintaining optimum network performance in high-demand environments. Additionally, it supports various protocols, including Ethernet and Token Ring, making it versatile and adaptable to existing infrastructure. The device accommodates a wide range of network transmissions, ensuring seamless integration and operation within diverse network ecosystems.

In terms of connectivity, the 3C13880 is equipped with multiple ports, allowing for extensive device interconnectivity. This feature is particularly beneficial in large organization settings, where multiple devices, such as servers and workstations, need to communicate effectively. Coupled with high-speed data transmission rates, this model ensures minimal latency, enhancing overall network efficiency.

On the other hand, the 3C13840 is designed with a focus on cost-efficiency without sacrificing performance. This model provides essential networking features suitable for smaller business environments or those seeking budget-friendly options. It delivers reliable throughput and the ability to support a moderate number of users, making it ideal for small to mid-sized offices.

Both the 3C13880 and 3C13840 incorporate technologies that prioritize security and reliability. Features such as VLAN support and QoS settings help optimize network performance while ensuring the security and integrity of data are maintained. The devices also support management tools that allow administrators to monitor network performance in real time, facilitating quick troubleshooting and enhancing overall network management.

In summary, both the 3Com 3C13880 and 3C13840 devices stand out in networking technology by offering unique features tailored to different organizational needs. While the 3C13880 appeals to enterprises needing high performance and robust capabilities, the 3C13840 provides an accessible option for those requiring effective and budget-conscious networking solutions. The legacy of 3Com continues to be evident in these products, reflecting their innovative approach to addressing the dynamic demands of modern networking.
Top Page Image Contents