3Com 3C13701, 3C13759, 3C13880, 3C13840, 3C13751 manual Connecting Interface Cable

Page 61

3Com Router 5000 and Router 6000 v2.41

Chapter 3

Module Guide

Multifunctional Interface Modules (Router 5000)

Figure 3-1475-ohm-to120-ohm adapter (with BNC connector)

Caution:

zFor the convenience of extending the connection of E1 120-ohm balanced twisted pair cable, you can use network interface connector.

zE1 120-ohm balanced twisted pair cable, network interface connector, 75-ohm-to-120-ohm adapter are optional accessories, and you need to make a selection when purchasing an E1VI module; otherwise, they are not provided.

3.2.6Connecting Interface Cable

Caution:

zSome measures are taken to protect Router E1 Voice Module. Still, you are recommended to install a special lightning arrester at the input end of its connection cable to obtain better lightning protection when the cable is led outdoors;

zRead the mark identifying a port before you connect a cable to it, making sure it is the correct port. Wrong connection tends to damage the MIM and even the Router.

Step 1: Plug the DB15 connector of the cable into the DB15 port on the Router E1 Voice Module module and fasten the screws;

Step 2: Connect the RJ45 connector of the cable to:

zThe peer device directly, if the resistance of the port to be connected is 120-ohm, and there is no need to extend the cable;

3-10

Page 60 Page 62
Image 61
Page 60 Page 62
Contents 3C13701 3C13751 3C13755 3C13759 3C13840 3C13880 3Com Router 5000 Family Router 6000 Family Module Guide3Com Corporation Campus Drive Marlborough, MA 01752-3064 Table of Contents Router 2-Port FXS/FXO/E&M MIM Modules 3Com Router 5000 and Router 6000 Module Guide 3Com Router 5000 and Router 6000 Module Guide Table of Contents Interface LEDs Interface Cable 3Com Router 5000 and Router 6000 Module Guide Vii 3Com Router 5000 and Router 6000 Module Guide Types of MIMs Types of SICsTypes of FICs SIC/MIM Purchasing Guideline Installation/Removal of SIC and MIMIII. Installing SIC Installing/Removing SICTools required II. Removing blank filler panel from SIC slotII. Installing MIM Installing/Removing MIMIV. Removing SIC III. Removing MIM Installing/Removing an FICTroubleshooting Interface Attributes Router 1-Port 10/100 SICAttribute Router 1-Port 10/100 SIC Interface Cable Connecting the Interface CableIntroduction Router 1-Port Serial SICSynchronous and asynchronous 24 RS232 Maximum Baud rate bps Transmission Distance mII. DTE and DCE AppearanceEquipment type Interface type Typical equipment DTEDTE, DCE Attribute Description Synchronous AsynchronousInterface LEDs 5V.24 RS232 DTE cable 24 RS232 DCE cable 7V.35 DTE cable 35 DCE cable Connecting Interface Cable9Router 2-Port ISDN-S/T SIC Router 2-Port ISDN-S/T SIC and Router 2-Port ISDN-U SICIsdn Attribute DescriptionLED Connecting Interface Cable 13Router 1-Port Fractional E1 SIC Router 1-Port Fractional E1 SICDIP Switch DIP switch Description Ohm Ohm impedance Impedance 8BIT Module GuideOt-s h rink able tu be Pos.15 Connecting Interface Cable BNC 20Router 1-Port Fractional T1 SIC Router 1-Port Fractional T1 SIC12Interface attributes of Router 1-Port Fractional T1 SIC 22 T1 cable Router 1-Port Analog Modem SIC Attribute Description Connector type RJ11Blinking means the connection is being set up Connecting Interface Cable 25Router 1-Port FXS/FXO SIC Router 2-Port FXS/FXO SIC 27Router 1-Port FXS SIC panel 29Router 2-Port FXS SIC panel Router 1-Port SAE SIC 31Router 1-Port SAE SIC panel 32V24 DTE cable 24 DCE cable 33V.24 DCE cable 35 DTE cable 37X.21 DCE cable RS449 DTE cable RS530 DCE cable Router 2-Port FXS/FXO/E&M MIM module Multifunctional Interface Modules Router1Router 2-Port FXS/FXO/E&M MIM MOdule II. Router 4-Port FXS/FXO/E&M MIM module3Router 2-Port FXS panel 7Router 4-Port FXO panel Interface cable of FXS/FXO modulesPBX II. Interface cable of E&M modulesRING0 RING1 TIP1 TIP0 Router E1 Voice Module Isdn PRI 11Router E1Voice ModuleActive Connecting Interface Cable Router T1 Voice Module CT1 16Router T1Voice ModuleReceived or/and transmitted T1VI cable 20 Ndec Ndec ModuleSpeed RUNDeny Troubleshooting Attribute Description Router 2-Port 10/100 MIM Router 2-Port 10/100 MIMII. Making Ethernet cables Ethernet cableRouter 4-Port Serial MIM Module 24 RS232 Baud rate bps Maximum transmission Distance m Bps II. Introduction to DTE and DCEDTE DCE Router 4-Port Serial MIM interface cable DB100 male Router 2 and 4-Port Enhanced Serial MIM Connecting interface cable of Router 4-Port Serial MIMDTE and DCE Interface Attributes Following figures show the 2 and 4-port panels 26 2-port panel 28V24 DTE cable 24 DCE cable 32X.21 DTE cable 21 DCE cable 36RS530 DTE cable RS530 DCE cable 4-Port CE1/PRI Router 2 and 4-Port CE1/PRI MIM ModulesAttribute Description Port module 38 2-port panel 412-port 120-ohm balanced twisted pair cable Interface cable of 2-port modulesII. Conversion cable for 4-port module 42120-ohm 4-port module conversion cable Internal DIP Switches 8BIT 3BIT OFF 4BIT 5BIT45Extending an 75-ohm unbalanced coaxial cable Connecting interface cable of 1E1/2E1 and modulesII. Connecting interface cable of 4-port Router 4-Port ISDN-S/T MIM Module DIP switch Description Default Setting 49ISDN S/T cable Router 2-Port CT1/PRI MIMmodule Router 2-Port CT1/PRI MIMLP/AL LINK/ACT51 T1 cable Router 1-Port Adsl Over Pots MIM Pots MIM Panel and Interface LEDAttribute Router 1-Port Adsl Over 29LEDs on the Router 1-Port Adsl Over Pots MIM panel Attribute Router 2-Port Adsl Over Pots MIMRouter 2-Port Adsl Over Panel and Interface LED Router NDEC2 Encryption Accelerator MIM 56Connecting the Router 2-Port Adsl Over Pots MIM57Router NDEC2 Encryption Accelerator MIM Feature DescriptionStatus IndicationAppearance of the Interface Card Router 4-Port E1 IMA MIME1 IMA MIM AAL5 Panels and Interface LEDsMeaning Connection of the Interface CableIntroduction to the Interface card Router 4-Port T1 IMA MIMRouter 4-Port T1 IMA MIM OFF the link is disconnected SMB Router 1-Port CE3 MIM Module65 E3/T3 cable Router 1-Port CT3 MIM Module Router 1-Port CT3 MIM panel is shown in the following figure Attribute Router 1-Port 10/100/1000 MIM Router 1-Port 10/100/1000 MIMMDI/MDIX 68Ethernet cable Panel and Interface LEDs Router 2-Port 10/100 FICAttribute Description Router 2-Port 10/100 2Ethernet cable Router 1-Port 100FX MM FIC/100FX SM FIC Attribute Description 100FX SM 100FX MM Attribute Description 100FX SM 100FX MM EthernetSNAP Interface Optical FiberConnecting the Interface Optical Fiber Attribute Port 10/100/1000 FIC Router 1-Port 10/100/1000 FIC7Ethernet cable Attribute Port Gigabit Ethernet FIC Router 1-Port Gigabit Ethernet Fiber FICOFF means no link is present on means a link is present 1-Port GEF FIC Connecting the Interface Optic FiberSFP Attribute Port GEF FICInterface Cable Router 4-Port/8-Port Enhanced Serial FIC 3Com Router 5000 and Router 6000 Module Guide Interface Attributes Panel and Interface LEDs 14V24 DTE cable 24 DCE cable 17V.35 DCE cable 21 DTE cable 21RS449 DCE cable RS530 DTE cable Router 4-Port CE1/PRI FIC Connector DB-25Router 4-Port CE1/PRI FIC Attribute Router 4-Port CE1/PRIOFF means no link is present on means a link is present Description Attribute Router 4-Port CE1/PRIInterface cable of the Router 4-Port CE1/PRI FIC 27120-ohm 4E1 adapter cable II. Interface cable of the Router 4-Port CE1/PRI FICCard Router 4-Port CE1/PRI FIC Internal DIP Switch29Extending an E1 75-ohm unbalanced coaxial cable DB-15 RJ-45 Network Router II. Router 4-Port Fractional T1 FIC Router 4-Port CT1/PRI FIC32 T1 cable RJ-45 Straight-through cable SMB Router 1-Port CE3 FICCE3 35 E3/T3 cable Router 1-Port CT3 FIC CT3 Attribute Router 1-Port E3 ATM FIC 11 8.8 Router 1-Port E3 ATM FIC38 E3/T3 cable Router 1-Port T3 ATM FIC Color State Attribute Router 1-Port T3 ATM FICLP/ALM LOSInterface Cable Attribute Router 1-Port OC-3 Fiber-optic Connector Number ConnectorsLED Sonet OC-3/SDH STM-1Yellow Solid Blinking Off Alarms Detected Layer Alarm TypeLOL, LOS, OOF, LOF LOP, AIS, RDI, REIAttribute Router 1-Port Adsl FIC Router 2-Port Adsl FIC Router 1/2-Port Adsl FICSupported service Adsl over the regular telephone line Router 1-Port Adsl FIC/Router 2-Port Adsl FIC 45Connecting the Router 1/2-Port Adsl FICInterface Attributes 48Connect the FIC Description Attribute Router 4-Port Router 4-Port E1 IMA FIC75-ohm 75-ohm 120-ohm50 75-ohm panel 5175-ohm 8E1 conversion cable Attribute Description Router 4-Port T1 IMA FIC Router 4-Port T1 IMA FICRouter 1-Port OC3 POS FIC SFP/LC Attribute Router 1-Port OC3 POS FICColor State AIS, RDI LOS, LOF, OOFLOP, AIS, RDI Following figure illustrates the 2-Port FXS panel OFF means that no link is present on means a link is present Router 1-Port E1 Voice FIC CE1 42LEDs on the Router 1-Port E1 Voice FIC panel Connecting the Interface Cable Router 1-Port T1 Voice FIC 64 T1VI cable Router NDEC2 Encryption Accelerator FIC Interface FeaturesPanel and LEDs Incorrect LED Reason Action to take Behaviors 23 RPU2 Encryption AcceleratorStatus LED Active LEDSpecifications SpecificationsLED and button LED and button DescriptionInterface ResetEncryption daughter card PWR1Attribute Description
Related manuals
Manual 94 pages 1.76 Kb

3C13751, 3C13701, 3C13840, 3C13759, 3C13880 specifications

The 3Com 3C13880 and 3C13840 are notable components within the realm of networking technology, primarily designed for enterprise-grade solutions. These devices belong to the 3Com family, which has long been recognized for its commitment to developing robust networking products tailored to facilitate efficient data transfers and improve connectivity across various platforms.

One of the standout features of the 3C13880 is its high-performance capabilities. This model supports advanced functions such as load balancing and fault tolerance, critical for maintaining optimum network performance in high-demand environments. Additionally, it supports various protocols, including Ethernet and Token Ring, making it versatile and adaptable to existing infrastructure. The device accommodates a wide range of network transmissions, ensuring seamless integration and operation within diverse network ecosystems.

In terms of connectivity, the 3C13880 is equipped with multiple ports, allowing for extensive device interconnectivity. This feature is particularly beneficial in large organization settings, where multiple devices, such as servers and workstations, need to communicate effectively. Coupled with high-speed data transmission rates, this model ensures minimal latency, enhancing overall network efficiency.

On the other hand, the 3C13840 is designed with a focus on cost-efficiency without sacrificing performance. This model provides essential networking features suitable for smaller business environments or those seeking budget-friendly options. It delivers reliable throughput and the ability to support a moderate number of users, making it ideal for small to mid-sized offices.

Both the 3C13880 and 3C13840 incorporate technologies that prioritize security and reliability. Features such as VLAN support and QoS settings help optimize network performance while ensuring the security and integrity of data are maintained. The devices also support management tools that allow administrators to monitor network performance in real time, facilitating quick troubleshooting and enhancing overall network management.

In summary, both the 3Com 3C13880 and 3C13840 devices stand out in networking technology by offering unique features tailored to different organizational needs. While the 3C13880 appeals to enterprises needing high performance and robust capabilities, the 3C13840 provides an accessible option for those requiring effective and budget-conscious networking solutions. The legacy of 3Com continues to be evident in these products, reflecting their innovative approach to addressing the dynamic demands of modern networking.
Top Page Image Contents