Radio Shack PRO-528 manual Programming trunked frequencies, You See Trunk System

Page 53

Beyond the Basics

the scanner. If it is set too high, it could prevent your scanner from locking on the control channel reliably. If it is set too low, it will slightly delay ﬁnding the control channel. The best setting is the same as for conventional reception and is critical for monitoring trunked systems.

programming trunked frequencies

Follow these steps to select, program, and store trunked frequencies.

1.Press E/PGM in conventional mode to set the scanner in programming mode. Then, press TRUNK. Your scanner beeps a tone. Then TRUNK and all of the bank numbers ﬂash.

2.Press the number key (1-9 and 0) of the desired target storage bank. Select one of the trunk systems by repeatedly pressing S or T to select a trunking system type, then press E/PGM.

Note: You can select from the following six systems:

Notes

You See	Trunk
	System

E2 – 800	Motorola
	Type II,
	800 MHz
	frequencies

53

Image 53

Contents PRO-528 1,000-Channel Handheld Trunking Scanner Contents Beyond the Basics Contents BasicsSpecial features Contents Frequently asked questions Contents Basics Your scanner’s features HOLD/RESUME PGM Program programs frequencies into channels Alert turns Input a number or characters Volume turn the scanner on or off and adjust the volume Basics Supplying power to your scanner Battery cautions Connecting an earphone/ headphone Connecting the antennaListening safely Attaching the belt clipAbout your scanner Basics Transferring data to or from another scanner or pcUnderstanding banks Service banksChannel storage banks Turning on the scanner and setting squelchPress SCAN/MANUAL Basics Storing known frequencies into channelsCopying/moving a frequency Searching for and temporarily storing active frequencies Bank No Frequency Step kHz MHz Chain searchStarting chain search Programming search ranges Storing found frequencies during chain searchDirect search Service bank searchSearch skip memory Weather searchBeyond the Basics Scanning the stored channels Manually selecting a channel Delay Special featuresLocking out channels Beyond the Basics Turning channel-storage banks on and offPriority MANUAL, HOLD/RESUME Using the keylockWired programming Cloning your scanner Using the auto backlight display Using the display backlightTurning the keytone off/on Search speedsSkipping data signals Turning the battery save function off/onReceiving nwr-same and weather alert signals Turning on the digital weather alert feature Testing digital weather alert toneProgramming a Fips code Programming Fips About Skywarn SkywarnBeyond the Basics Beyond the Basics Signal Stalker Setting the Signal Stalker I options Beyond the Basics PGM Trunking operation Using Signal StalkerSimultaneous trunking Beyond the Basics Setting the scanner to the trunking modeSetting squelch for the trunking mode You See Trunk System Programming trunked frequenciesLTR Depending upon the trunk system selected Searching a trunked bank Beyond the Basics Turning a trunked bank on or off Turning the status bit ignore s-bit on or off Beyond the Basics Skipping a trunked bankTrunk Identifying a trunked frequencyEdacs Ed talk group ID range search Locking out talk group IDs Using Hold to monitor an active talk group IDCLR /DELAY, 0, 1, then Srch Unlocking all talk group IDs Unlocking a single talk group IDMonitoring talk group IDs Using trunk scanning Scan DelayManually storing talk group IDs in talk group ID lists Using talk group ID listsTo enter a Type 1 ID Motorola talk groupsTo enter a Type 2 Talk Group ID Entering Edacs partial talk groups Beyond the Basics Edacs Ed talk groupsYou Press To Scan LTR talk groupsScanning the talk group ID lists All of them Priority talk group ID scanningBeyond the Basics Scanning type I and hybrid trunked systems Preset ﬂeet maps table E1P4 E1P5 E1P6 E1P13 E1P14 E1P15 Programming a ﬂeet map Beyond the Basics Selecting a preset ﬂeet mapBeyond the Basics Programming the Base and Offset frequencies Programming a hybrid systemBeyond the Basics Turning the Motorola disconnect tone detect function On/Off Transmitted or there is no signal at all My scanner is on but will not scan, why? Why won’t my scanner work at all?Why is ﬂashing? Beyond the Basics Why doesn’t my keypad work?Why am I getting poor or no reception? Why does Error appear?Why am I missing replies to conversations? Why isn’t my scanner acquiring a data channel?Why is the frequency used for the data channel missing? How do I reset my scanner? FCC notice Beyond the Basics Scanning legally Care Service and repairSensitivity AM/FM SpeciﬁcationsFrequency Coverage Power Operating TemperatureSearch Speed Current DrainBeyond the Basics Beyond the Basics Beyond the Basics 06A06