Radio Shack PRO-528 manual How do I reset my scanner?

Page 83

Beyond the Basics

Type II systems. Set the scanner to receive Type I trunked frequencies. See “scanning type I and hybrid trunked systems”.

The selected ﬂeet map is incorrect. Try another preset ﬂeet map or program your own ﬂeet map (see “scanning type I and hybrid trunked systems”).

Enter all of the trunk’s frequencies: see “programming trunked frequencies”.

How do I reset my scanner?

If the scanner’s display locks up or stops operating properly, you might need to reset the scanner.

Caution: This procedure clears all the information you have stored in the scanner. Before you reset the scanner, try turning

it off and on to see if it begins working properly. Reset the scanner only when you are sure it is not working properly.

1.Turn off the scanner.

2.While holding down 2, 9 and HOLD/ RESUME, turn on the scanner. CLEAr ﬂashes for about 5 seconds as the scanner clears its memory.

Note: Do not turn off the scanner Notes again until CLEAr stops ﬂashing.

Otherwise, the scanner might not clear its memory properly.

83

Image 83

Contents PRO-528 1,000-Channel Handheld Trunking Scanner Contents Beyond the Basics Contents BasicsSpecial features Contents Frequently asked questions Contents Basics Your scanner’s features HOLD/RESUME PGM Program programs frequencies into channels Alert turns Input a number or characters Volume turn the scanner on or off and adjust the volume Basics Supplying power to your scanner Battery cautions Connecting an earphone/ headphone Connecting the antennaListening safely Attaching the belt clipAbout your scanner Basics Transferring data to or from another scanner or pcUnderstanding banks Service banksChannel storage banks Turning on the scanner and setting squelchPress SCAN/MANUAL Basics Storing known frequencies into channelsCopying/moving a frequency Searching for and temporarily storing active frequencies Bank No Frequency Step kHz MHz Chain searchStarting chain search Programming search ranges Storing found frequencies during chain searchDirect search Service bank searchSearch skip memory Weather searchBeyond the Basics Scanning the stored channels Manually selecting a channel Delay Special featuresLocking out channels Beyond the Basics Turning channel-storage banks on and offPriority MANUAL, HOLD/RESUME Using the keylockWired programming Cloning your scanner Using the auto backlight display Using the display backlightTurning the keytone off/on Search speedsSkipping data signals Turning the battery save function off/onReceiving nwr-same and weather alert signals Turning on the digital weather alert feature Testing digital weather alert toneProgramming a Fips code Programming Fips About Skywarn SkywarnBeyond the Basics Beyond the Basics Signal Stalker Setting the Signal Stalker I options Beyond the Basics PGM Trunking operation Using Signal StalkerSimultaneous trunking Beyond the Basics Setting the scanner to the trunking modeSetting squelch for the trunking mode You See Trunk System Programming trunked frequenciesLTR Depending upon the trunk system selected Searching a trunked bank Beyond the Basics Turning a trunked bank on or off Turning the status bit ignore s-bit on or off Beyond the Basics Skipping a trunked bankTrunk Identifying a trunked frequencyEdacs Ed talk group ID range search Locking out talk group IDs Using Hold to monitor an active talk group IDCLR /DELAY, 0, 1, then Srch Unlocking all talk group IDs Unlocking a single talk group IDMonitoring talk group IDs Using trunk scanning Scan DelayManually storing talk group IDs in talk group ID lists Using talk group ID listsTo enter a Type 1 ID Motorola talk groupsTo enter a Type 2 Talk Group ID Entering Edacs partial talk groups Beyond the Basics Edacs Ed talk groupsYou Press To Scan LTR talk groupsScanning the talk group ID lists All of them Priority talk group ID scanningBeyond the Basics Scanning type I and hybrid trunked systems Preset ﬂeet maps table E1P4 E1P5 E1P6 E1P13 E1P14 E1P15 Programming a ﬂeet map Beyond the Basics Selecting a preset ﬂeet mapBeyond the Basics Programming the Base and Offset frequencies Programming a hybrid systemBeyond the Basics Turning the Motorola disconnect tone detect function On/Off Transmitted or there is no signal at all My scanner is on but will not scan, why? Why won’t my scanner work at all?Why does Error appear? Beyond the Basics Why doesn’t my keypad work?Why is ﬂashing? Why am I getting poor or no reception?Why am I missing replies to conversations? Why isn’t my scanner acquiring a data channel?Why is the frequency used for the data channel missing? How do I reset my scanner? FCC notice Beyond the Basics Scanning legally Care Service and repairSensitivity AM/FM SpeciﬁcationsFrequency Coverage Current Drain Operating TemperaturePower Search SpeedBeyond the Basics Beyond the Basics Beyond the Basics 06A06