Radio Shack PRO-2051 manual Beyond the Basics Priority scan, Changing the priority channel

Page 26

Beyond the Basics

priority scan

When priority scan is turned on, your scanner checks the priority channel in the banks you selected every two seconds for activity. If a signal is present on the priority channel, your scanner monitors the channel until the transmission ends, then resumes normal scanning. You can designate one channel in each bank as a priority channel. By default, the ﬁrst channel in each bank is the priority channel, but you can change this.

To activate Priority Scan (in either the private scan mode or scan hold mode):

1.Press PRI. PRI appears.

If you have locked out all the priority channels, an error

Note

message appears when you select priority mode.

2.Press PRI again to deactivate priority scan. PRI disappears.

changing the priority channel

You cannot eliminate the priority channel, but you can change it to any one of the 100 available channels in each bank.

1Turn off the priority function if it is on.

2. Press HOLD/RESUME.

3. Select a new priority channel by entering the channel number using the keypad. Then, press HOLD/RESUME.

4. Press FUNC + PRI. When the priority channel has been changed, P appears on the display.

Note

Priority in trunking mode works just the same, except you set them for talk group IDs instead of setting priorities for

26

Image 26

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Basics Power your scannerSet up your scanner BasicsScanning a private bank Advanced scanner featuresBeyond the Basics Highway patrol alertsWired programming Contents SkywarnSignal Stalker WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleThrough your vehicle’s ignition negative ground only Power your scannerFrom a wall outlet From your vehicle’s cigarrette lighter Rear ViewConnect your scanner Connecting the supplied antennaConnecting an external antenna Connecting an external speaker Use extreme caution when installing or removing anListening Safely Set the squelch Set up your scannerTurn on your scanner Scanning overview Basics Listen to preprogrammed frequenciesCommon scanner terms Basics Channel storage banks Advanced scanner featuresBeyond the Basics Storing known frequencies into channelsBeyond the Basics Beyond the Basics Deleting a stored frequency Locking out a channel in hold modeLocking out a channel in scanning mode Locking out channels Restoring all locked-out channels Restoring a locked-out channel in hold mode Memory lock Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Selecting the state Highway patrol alertsHighway patrol/local police scanning State Code Order Press these buttons Action Highway warning alert Setting the alert tone volumeBeyond the Basics Scan hold Muting the alert tone Adjusting alertHighway patrol priority channels Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold modeID search hold mode Direct entry id hold modeID search mode Deleting a stored ID ID monitor modeProgramming scan lists during search Restoring locked-out IDs ID lockoutReviewing ID lockout Trunking frequency conﬁrmation Setting the delay mode for trunking modeSetting priority in trunking mode Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesAFS partial entry Special Edacs featuresBeyond the Basics An Edacs trunked system Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet mapsFleet Map Size Codes Programming a Hybrid system Size code restrictionsProgramming a user ﬂeet map You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Speciﬁcations If FrequenciesGlossary Service and repair Care