Radio Shack 20-164 manual FCC Notice

Page 51

by traveling to the scene of an incident without authorization.

We encourage responsible, legal scanner use.

FCC Notice

	This equipment has been tested and found to
	comply with the limits for a scanning receiver,
	pursuant to Part 15 of the FCC Rules. These
	limits are designed to provide reasonable
	protection against harmful interference in
	a residential installation. This equipment
	generates, uses and can radiate radio frequency
	energy and, if not installed and used in
	accordance with the instructions, may cause
	harmful interference to radio communications.
	However, there is no guarantee that interference
	will not occur in a particular installation. If this
	equipment does cause harmful interference
	to radio or television reception, which can be
	determined by turning the equipment off and
	on, the user is encouraged to try to correct the
	interference by one or more of the following
	measures:.
	• Reorient or relocate the receiving antenna..
f	• Increase the separation between the
f	equipment and receiver..

w• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

uconditions:.

1.This device may not cause harmful interference..

2.This device must accept any interference received, including interference that may cause undesired operation.

51

Image 51

Contents Triple Trunking What’s IncludedContents Contents Your Scanner Volume / OFFConnecting the Antenna Attaching the Belt ClipTo attach the supplied antenna Batteries Powering Your ScannerTo charge batteries To install batteriesTo use an external power source External PowerHeadphones and Speakers To lock the keypad Keytones and KeylockBacklight and Contrast To set the keytoneTo change the display contrast To change the backlight modeSquelch and Attenuator To turn on the backlightTo set squelch To set the attenuator modeScanner Setup DelayTo turn the delay on / off To define a channel Defining a ChannelTo copy a frequency Copying a FrequencyDeleting Saved Frequencies To delete a saved frequencyTo delete all saved frequencies in a bank Scanner Cloning To define a channel’s Ctcss or DCS codeTo save a Ctcss or DCS code To activate Seek Search SearchingSeek Search To clone the scanner dataTo search preprogrammed search banks Search BanksTo search banks SR0-SR2 ZeromaticTo program the search range of Bank SR7 Signal StalkerProgramming a Search Range To activate ZeromaticTo use Signal Stalker Special Signal StalkerTo review and unlock frequencies To use Special Signal StalkerLocking Out Frequencies To lock out a frequencySaving Found Frequencies To unlock all frequencies in a search bankTo save a frequency found during a search To locked out a channel ScanningLocking Out Channels To scanTo turn on the priority feature Priority ScanningTo review all locked out channels Weather Alerts To make an existing channel a Priority channelTo modify the Priority channel To program a Fips code Same Standby ModeTo perform a weather scan To program a weather channel into priority channelTo review stored Fips codes Code. The format of a Fips code isSkywarn To enter Same standbyTo test the weather alert To find a frequency to monitor MonitoringTo use Skywarn To monitor a channelTo define a Trunking Bank Trunking SetupTo set a default tuning frequency Defining a Trunking BankMotorola Trunking Setup To set Open or Closed mode for a bankTrunking Modes To program a fleet map Fleet MapsFor Motorola Type II, enter Base and Offset FrequenciesUHF-Hi 806-960 MHz To program 800 MHz Motorola trunking Edacs Trunking SetupTo save a correct Home Repeater LTR Trunking SetupSearching for Talk Group IDs Saving a Talk Group IDTo search for Talk Group IDs To define a Talk Group ID Deleting Talk Group IDsSaving Trunking Channels To delete a Talk Group IDTo delete ALL talk group IDs in a bank To change the scanning direction, press  or  Trunk ScanningTo lock out Talk Group IDs Trunking DelayTo set a Talk Group ID delay Locking Out Talk Group IDsTo turn off a sub-bank while scanning Turning Off Sub-BanksTo review locked-out Talk Group IDs To turn off a sub-bankTo set Talk Group ID Hold Scanner MaintenanceTalk Group ID Hold Text TagsPage Working at all TroubleshootingTo display the Talk Group ID Scanner is notDoes not scan Scanner does notReceive any stations Or reception is poor Scanner is on butBirdie Frequencies Service and Repair Initializing the ScannerTo initialize the scanner Scanning Legally FCC Notice References Appendix a GlossaryAppendix B Search Banks Search bank SR1 CB band Receive mode AM Search bank SR2 FRS/GMRS/MURS band Search bank SR4 Aircraft Receive mode AM, FM Ctcss Codes Appendix C Ctcss / DCS CodesAppendix D Signal Stalker Bands All BandDCS Codes PubSafety Band Appendix E Talk Group Format MotorolaTo use AFS format 406-512 MHz 764-960 MHz Appendix F Specifications9V DC Preprogrammed Frequencies AddendumPurple DOT Purple DOT BB Business Band Police Departments Police Dept Nascar Track Announcer Security Alarm Security Company Companies DOT Business Band DOT BB Limited One-year Warranty

Related manuals

Manual 62 pages 41.14 Kb