Dynaudio SUB 250 manual Connecting the subwoofer, Subwoofer inputs

Page 9

Before operation

SUB I/O

 

LFE/Slave In

SAT/SUB Input

Connecting the subwoofer

CAUTION

DAMAGE OF DEVICE DUE TO IMPROPER CONNECTION!

XSet the mains power switch to OFF before connecting the SUB 250.

XOnly switch the subwoofer on (mains power switch to ON) after all connections and set up steps have been properly completed.

Note:

•The Dynaudio SUB 250 can be controlled by any source provided with a LFE or preamplifier output. In the operating manual the expression “processor/receiver” will be used for all these sources.

Subwoofer inputs

The Dynaudio SUB 250 provides two different signal inputs:

SUB I/O - LFE/Slave In

LFE

MODE

Slave

+

SUBSAT

Lowpass Highpass

+

GAIN

PHASE

This input allows the LFE (Low Frequency Effect) channel to be connected, which is used in Home Cinema systems to reproduce low frequency effects.

The signal is:

•reproduced by the subwoofer

•routed to the SUB I/O - LFE/To Slave output for a second subwoofer to be connected.

The SUB Lowpass control has no impact on this input.

SAT/SUB Input

This input allows the connection of the full bandwidth signal from the processor/ receiver (preamplifier out).

The signal is:

• reproduced by the subwoofer,

• routed to the SAT Output terminals. Low frequencies are cut-off according to the

SAT Highpass setting,

• routed to the SUB I/O - LFE/To Slave output for a second subwoofer to be

connected. High frequencies are cut-off according to the SUB Lowpass setting.

+

SUB I/O

SAT Output

To Slave

 

Subwoofer

See figure left for correlations between input, output and settings.

Note:

•All SUB 250 inputs and outputs are low level terminals. Thus, neither a power amplifier output must be connected to the subwoofer nor loudspeakers can be driven by the subwoofer directly!

Dynaudio SUB 250

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operating Guide / Bedienungsanleitung SUBInhalt ContentsDynaudio SUB Important Safety Instructions Safety signs Signal wordsRisk of Electric Shock Do not Open Used signs and symbols About this operating manualHow this operating manual is structured Grille UnpackingControls and connections Connecting the subwoofer Subwoofer inputsDamage of Device DUE to Improper Connection ➊ Connecting the SAT/SUB input Connecting a single subwoofer➋ Connecting the LFE channel Connecting multiple subwoofersConnecting loudspeakers Switching the subwoofer on/off Power ON/OFFAutomatic mode Connecting speakersSelecting the subwoofer cut-off frequency SUB Lowpass Adjusting the volume GainHigh Sound Levels Selecting the cut-off frequencySetting the satellite cut-off frequency SAT Highpass Setting the phase PhaseFinding the correct phase setting Setting the cut-off frequencyPositioning the subwoofer Choose adequate music materialImpact of room-modes Corner placement Using multiple subwoofersPositioning possibilities Next to wall, away from cornerGeneral tips Volume GainCross-over frequencies set correctly Cut-off frequenciesSubwoofer too low, main speakers too high Subwoofer too high, main speakers too lowControl possibilities General tipsSpecific tips Damage of Small Satellite Speakers Check this first TroubleshootingChanging the fuse Technical SpecificationsRisk of Fire Changing the fuseWarranty Sehr geehrter Musikliebhaber Service SicherheitshinweiseBestimmungsgemäßer Gebrauch Zu dieser Anleitung Verwendete Zeichen und SymboleAuspacken Zum Aufbau dieser AnleitungStoffabdeckung ➋ AC in Netzanschluss Anschluss- und BedienelementeSubwoofer Eingänge Subwoofer anschließenMehrere Subwoofer anschließen Einen einzelnen Subwoofer anschließen➊ SAT/SUB Input anschließen ➋ LFE-Kanal anschließenLautsprecher anschließen Lautsprecher anschließenLautstärke einstellen Gain Ein-/Ausschalten Power ON/OFFAutomatischer Modus Schädigung DES Gehörs Durch ZU Hohe SchallpegelPhase einstellen Phase Subwoofer-Grenzfrequenz wählen SUB LowpassGrenzfrequenz einstellen Die richtige Phasen-Einstellung finden Satelliten-Grenzfrequenz anpassen SAT HighpassSatelliten-Grenzfrequenz anpassen Subwoofer aufstellen Verwenden Sie geeignetes MusikmaterialEinfluss von Raum-Moden Mehrere Subwoofer verwenden AufstellungsmöglichkeitenEckaufstellung Wandaufstellung mit Abstand zur RaumeckeLautstärke Gain Generelle TippsÜbergangsfrequenzen optimal eingestellt GrenzfrequenzenSubwoofer zu niedrig, Lautsprecher zu hoch eingestellt Subwoofer zu hoch, Lautsprecher zu niedrig eingestelltGenerelle Einstelltipps EinstellmöglichkeitenSpezielle Einstelltipps Schwache Verstärker und kleine Lautsprecher entlastenBeschädigung DER SATELLITEN-LAUTSPRECHER Prüfen Sie zuerst folgende Punkte FehlersucheSicherung ersetzen Feuergefahr Durch Falsche SicherungSicherung wechseln Parameter Daten Technische DatenGarantie Dynaudio A/S

SUB 250 specifications

The Dynaudio SUB 250 is a powerful and sophisticated subwoofer designed to deliver deep, accurate bass performance for music enthusiasts and home theater aficionados alike. This subwoofer boasts a modern design that seamlessly integrates into any environment while providing high-quality audio reproduction.

At the heart of the SUB 250 is a robust 10-inch bass driver, engineered to deliver a precise and dynamic sound across a wide frequency range. The driver utilizes Dynaudio's proprietary technology to ensure low distortion, resulting in a clean and powerful bass response. This translates into an immersive listening experience, where every note and beat is felt as much as it is heard.

One of the key features of the SUB 250 is its advanced amplifier, capable of delivering up to 250 watts of peak power. This powerful amplification allows the subwoofer to handle demanding audio tracks without compromising performance. The class D amplifier ensures high efficiency and less power consumption, making the SUB 250 not only powerful but also energy-efficient.

The SUB 250 incorporates several intelligent technologies to enhance performance and usability. One such feature is the adjustable crossover frequency, which allows users to seamlessly integrate the subwoofer with their existing speaker systems. This flexibility is crucial for achieving the perfect balance between the subwoofer and the main speakers, ensuring optimal sound reproduction across the entire audio spectrum.

Additionally, the SUB 250 is equipped with multiple connection options, including RCA and speaker-level inputs, making it compatible with various audio systems. This versatility ensures that users can easily incorporate the subwoofer into their home entertainment setups, whether they are utilizing a stereo system or a full surround sound configuration.

The design of the SUB 250 is another highlight, featuring a sleek cabinet that minimizes resonance and vibration. The enclosure is constructed to support the driver effectively, allowing for extended low-frequency output without compromising sound quality. The subwoofer is available in a variety of finishes, allowing it to blend seamlessly with any décor.

In summary, the Dynaudio SUB 250 is an elite subwoofer that excels in delivering deep, accurate bass while offering advanced features and technologies for flexibility and ease of use. Its combination of powerful performance, intelligent design, and versatility makes it an excellent choice for anyone looking to enhance their audio experience.
Top Page Image Contents