Enable or Disable Alarm and Chime, To Stop Alarm

TIME PROJECTION

The Sport Alarm Clock can project the time display for a short period when operating on batteries, or continuously when using the AC/DC adapter. The clock is designed to project the time image on the ceiling in red, no focusing is required.

PC04PC06

PC07

NOTE: Time display on the ceiling and the time on the LCD display cannot be viewed simultaneously, as their viewing directions are opposite. Place the unit at the head of your bed to view the projected image correctly.

CURRENT TIME PROJECTION

Press "LIGHT/SNOOZE" button to turn on the LCD backlight and project the time display onto the wall or the ceiling for 3 seconds.

CONTINUOUS TIME PROJECTION

Connect AC/DC adapter (optional) to project the time display continuously.

CALENDAR AND CLOCK DISPLAY MODES The Alarm Clock has a three (3) display modes:

TIME, DATE and ALARM

The current time is displayed in hour-minutes format which is the default display mode. The date is displayed in month-date format.

The alarm time is displayed in hour-minutes format.

ENABLE OR DISABLE ALARM AND CHIME

• Press SET button in TIME display mode. Alarm hour and minute digits will flash.

• Press MODE button to enable or disable the alarm and chime in the following sequence:

ALARM ON-

ALARM&CHIMEON-

CHIME ON-

ALARM&CHIME OFF -

ALARM ON-

• Press SET button to confirm the alarm and chime status. Clock will

go into TIME and DATE set mode. Wait and clock will return to TIME display mode.

TO STOP ALARM

To stop the alarm for 24 hours, press SET when alarm is activated.

To stop alarm for 5 minutes, press SNOOZE/LIGHT button

If no button is pressed, alarm will stop in 2 minutes. Press MODE button to disable the alarm in ALARM display format while alarm time digits are flashing. (The bell icon will disappear from the display when alarm is disabled).

CHIME

When CHIME is activated, it will sound at every hour.

PRECAUTIONS

This product is engineered to give you years of satisfactory service if handled carefully.

Here are a few precautions:

1. Do not immerse the unit in water.

2. Do not clean the unit with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits.

3. Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts.

4. Do not tamper with the unit's internal components. Doing so will invalidate the warranty and may cause damage. This unit contains no user-serviceable parts.

5. Use only fresh batteries. Do not mix new and old batteries.

6. Read the user's manual thoroughly before operating the unit.

SPECIFICATIONS

Projection

Current time display projected onto the ceiling or wall Fixed red display projection

Calendar and Clock

12/24 hour display in hh : mm format

Date Format: Month - Day format

Single 2-minute crescendo alarm with snooze and chime LED backlight

Power

2 AAA batteries (not included) AC/DC Adapter (3V, 100mA), center pin positive (optional)

Dimensions

4.33 (L) x 4.72 (H) x 4.33 (D) inches

SETTING THE CLOCK

TIME AND DATE

After batteries are installed as shown inside the battery compartment, the default time will be displayed as “1:00” To set current date and time:

1). Press SET button 4 times, and the MONTH will be displayed as “1”.

2). Press MODE button to set the current month.

3). Press SET button and the DAY will be displayed.

4). Press MODE button to set the current day.

5). Press SET button again and the

HOUR will be displayed as 1: A. 6). Press MODE button to set current

hour (AM, 24 hour, PM). 7). Press SET button and the

MINUTES will be displayed. 8). Press MODE button to set the

correct minute.

9). Press SET button to complete setting the month, date, hour and minute.

10). Press MODE button to return clock to normal operation.

24 HOUR TIME FORMAT

Press MODE button until the desired hour in “24 hour” format is shown. To return to “12 hour” format continue pressing MODE.

ALARM

If the alarm is activated, it will sound at the set time and the (bell icon) will flash.

To review the alarm time, press MODE button once in TIME display and the default alarm time will be displayed as “1:00” and “ALARM” will be displayed in the top left of the LCD display.

To review the date, press MODE button when the ALARM TIME is displayed.

When MODE is pressed again the seconds will be displayed.

To return to the TIME display, press MODE button again or wait for it to change back.

TO SET ALARM TIME

Press SET button twice in TIME display. If the alarm is being set for the first time, “1:A” will be displayed

with flashing, and “ALARM” will display in the top left.

Press MODE button to adjust the desired alarm HOUR.

Press SET button to set the desired alarm MINUTES, the alarm minutes “00”will flash.

Press MODE button to adjust the desired alarm minutes.

Press SET button again to confirm set alarm time. The clock will return to the TIME display mode.

STANDARD WARRANTY INFORMATION

This product is warranted from the manufacturing defects

for one year from date of retail purchase. It does not

cover damages or wear resulting from accident, misuse,

abuse, commercial use, or unauthorized adjustment and/

or repair.

Note that online product registration is required to ensure

valid warranty protection.

To register your product, go to our Company website at:

www.digiviewtime.us. Click Online Product Registration

under the Customer Service menu.

Should you require assistance with this product and its

operation, please contact our Customer Service Hotline

1(866) 443 3543

Please direct all returns to the place of the original

purchase. Should this not be possible, contact Customer

Service Hotline for assistance and to obtain a Return

Merchandise Authorization (RMA). Returns without a

return authorization will be refused. Please retain your

original receipt as you may be asked to provide a copy

for proof of purchase.

Hideki Electronics, Inc. reserves the right to repair or

replace the product at our option.