JL Audio 450/4V2 owner manual TRI-AMPLIFIED Systems, W 4FMFDUi1&2wPOUIFiSignal Fromw

Page 11

TRI-AMPLIFIED SYSTEMS

Tri-amplified systems are defined as systems in which separate amplifier channels drive low-frequency (LF), mid-frequency (MF) and high-frequency (HF) speakers and are separately filtered to send appropriate frequency ranges to each speaker system.

The most common application of tri- amplification in mobile audio is to drive a subwoofer system from one or more amplifiers or channels (LF channels), mid-range speakers from a separate amplifier or set of channels (MF channels) and high-frequency speakers from a separate amplifier or set of channels (HF channels). One such configuration is to run subwoofers off the LF channel(s), mid- bass speakers off the MF channels, and a passively crossed over mid/high frequency component speaker systems on the HF channels. Another approach is to run subwoofers off the LF channel(s), mid-woofers off the MF channels and tweeters off the HF channels (all actively crossed over).

By activating the CH 1&2 bandpass filter feature, the 450/4v2 can easily be configured to drive a tri-amplified system in conjunction with a separate subwoofer amplifier that includes a low-pass filter. CH 3&4 of the 450/1 will drive the HF speakers (75W x 2), CH 1&2 will drive the MF speakers (150W x 2) and the separate subwoofer amp(s) will drive the LF speakers (subwoofers).

Input connection options for the Tri-Amplified Stereo mode are as follows:

A)No User Adjustability

Required: a basic source unit or processor with left and right stereo outputs.

Input Connections: a single pair of stereo source unit outputs is connected to the CH

JOQVUTPGUIFW TFMFDUi2chwPO UIFiInput ModewTXJUDIJOUIFiCH 1&2 Input Sectionw 4VCXPPGFSBNQMJGJFSJOQVUT

are connected to the preamp outputs of the

W 4FMFDUi1&2wPOUIFiSignal Fromw

TXJUDIJOUIFiPreamp Output Sectionw

Result: the relative level of all channels will be

GJYFECZUIFWTiInput Sens.wTFUUJOHT

and will not be user adjustable from the front of the vehicle.

B)Fade Subwoofer Level vs. MF/HF Level Required: a source unit or processor with front

and rear pairs of outputs is required. Input Connections: one stereo pair of source

unit outputs is connected to the CH 1&2

JOQVUTPGUIFW TFMFDUi2chwPOUIF

iInput ModewTXJUDIJOUIFiCH 1&2 Input Sectionw BOEUIFTFDPOETUFSFPQBJSPGTPVSDF unit outputs is connected to the subwoofer amplifier inputs. In this mode, the 450/4v2’s preamp output is not used.

Result: the user has the ability to adjust the level of the subwoofer channel relative to the mid and high-frequency channels via the source unit’s fader control, without exceeding the maximum clean output level set by each

BNQMJGJFSTFDUJPOTiInput Sens.wDPOUSPMT

C)Subwoofer Level Control Only Required: a source unit or processor with left, right and dedicated subwoofer outputs is required.

Input Connections: one stereo pair of source unit outputs is connected to the CH 1&2

JOQVUTPGUIFW TFMFDUi2chwPOUIF

iInput ModewTXJUDIJOUIFiCH 1&2 Input Sectionw BOEUIFTPVSDFVOJUTEFEJDBUFE subwoofer output is connected to the subwoofer amplifier inputs. In this mode, the 450/4v2’s preamp output is not used.

Result: the user has the ability to control the absolute level of the subwoofer channel relative to the MF and HF channels.

! I M P O RTA N T

Set the subwoofer amplifier’s “Input Sens.” with the source unit’s subwoofer level control set at 3/4 of full output. Refer to the subwoofer amplifier owner’s manual for proper adjustment.

Crossover setup for tri-amplified 3.1 system with one 450/4v2 and a separate subwoofer amplifier:

Once the input and preamp output sections have

CFFODPOGJHVSFEBQQSPQSJBUFMZHPUPUIFiCH 1&2 Filter SectionwPGUIFW5IFTFTFUUJOHT

will determine the high-pass cutoff and slope of the bandpass filtering applied to the MF (mid-

GSFRVFODZ DIBOOFMT4FMFDUix1wPOUIFiFreq.

RangewTXJUDIiBPw CBOEQBTT POUIFiFilter

TypewTXJUDIBOEi12dBwPSi24dBwPOUIF

iFilter Mode/SlopewTXJUDIBOEBOBQQSPQSJBUF

iFilter Freq.w )[JTBHPPETUBSUJOHQPJOU

5IFiInfrasonic FilterwBOEiBass EQwGFBUVSFT

cannot be used in this mode.

/FYUUVSOZPVSBUUFOUJPOUPUIFiCH 3&4 Input Sectionw5IFTFTFUUJOHTXJMMEFUFSNJOF

the high-pass cutoff and slope of the high pass filtering applied to the HF (high-frequency) channels as well as the low-pass cutoff frequency and slope for the MF channels’ bandpass filter.

4FMFDUix1wPOUIFiFreq. RangewTXJUDIJGZPVS

desired MF to HF crossover frequency is below

)[4FMFDUix10wPOUIFiFreq. RangewTXJUDI

if your desired MF to HF crossover frequency

JTBCPWF)[4FMFDUiHPw IJHIQBTT POUIF

iFilter TypewTXJUDIBOEi12dBwPSi24dBw

POUIFiFilter Mode/SlopewTXJUDIBOEBO BQQSPQSJBUFiFilter Freq.w

After proper adjustment of the 450/4v2’s CH 1&2 and CH 3&4, and the subwoofer amplifier’s

iInput RangewBOEiInput Sens.wZPVDBOGJOF

tune filter frequencies and slopes and attenuate the LF, MF and HF channel pair or with the

iInput Sens.wDPOUSPMTUPBDIJFWFQSPQFSCBMBODF 'PSQSPQFSBEKVTUNFOUPGUIFiInput Sens.w

controls of the 450/4v2 use the method shown in Appendix B (page 22). For precise filter frequency information for the 450/4v2 refer to Appendix A (page 22). Refer to the subwoofer amplifier owner’s manual for proper adjustments.

20 JL Audio - 450/4v2 Owner’s Manual

21

Image 11

Contents Four-channel system amplifier Serial Number Installation ApplicationsPlanning Your Installation Protect Your HearingAs we said, it’s very flexible Typical Installation SequenceProduct Description JL Audio 450/4v2 is a four-channel systemFuse Requirements Power ConnectionsCH 1&2 Filter Section Crossover ControlsSpeaker Outputs Preamp Output SectionJL Audio Technical Support Status Indicator Lights Servicing Your JL Audio AmplifierProtection Circuitry Bi-Amplified System with one 450/4v2 System ConfigurationsBI-AMPLIFIED Systems Input SectionwBOETFMFDUix1wPOUIFiFreq Cannot be used in this modeFade HF Front to Rear with Non-Fading Subwoofer Level ICH 1&2 Filter Sectionw4FMFDUix1wPOUIFJL Audio 500/1v2 or 1000/1v2 recommended JOQVUTPGUIFW TFMFDUi4chwPOUIFGJYFECZUIFWTiInput Sens.wTFUUJOHT W 4FMFDUi1&2wPOUIFiSignal FromwTRI-AMPLIFIED Systems TXJUDIJOUIFiPreamp Output Sectionw Appendix B Appendix aLeading cause of misdiagnosed amplifier failures Appendix C Trouble ShootingHow do I properly set the input sensitivity on my amplifier My amplifier doesn’t turn onAppendix D CH 1 & 2 Speaker Outputs Installation NotesPage International Warranties Limited Warranty Amplifiers USAIf you need service on your JL Audio product JL Audio, Inc