EAW D S A 2 5 0, D S A 2 3 0 owner manual 9b Retainer Bolt Installation

Page 28

1/4-20 X 3 LG HEX HEAD SCREW & LOCK WASHER

1/4-20 WELD NUT

Figure 5.5.9b Retainer Bolt Installation

CABLE CHANNELS

Figure 5.5.9c Cable Routing

1.Install at least one of the supplied 1/4-20 X 3 in Retainer Bolt with its lock washer through the side of either the top or bottom Wall/Enclosure Bracket and snugly tighten. The bolt threads into a weld nut on the side of the Wall Bracket. This Retainer Bolt prevents the enclosure from being lifted off the Wall Brackets without first removing the bolt. Note that the Retainer Bolt does not “clamp” or support anything. It serves only to retain the enclosure on the wall brackets, not to lock it into position.

2.Route cabling as required using the rear channels in the enclosures extrusion.

3.Rotate the enclosure to the desired horizontal angle. Firmly tighten each Enclosure Bracket Bolt to secure the enclosure in the desired position.

ENCLOSURE BRACKET BOLT

Figure 5.5.9d Secure the Enclosure Position

28

Image 28

Contents Page Introduction Safety Mechanical Drawings Introduction Safety ChapterE N E R a L P R E C a U T I O N S H i p p i n g D a m a g e Chapter UnpackingE t u r n i n g P r o d u c t s t o E AW E s c r i p t i o n U d i o S i g n a l Co n n e c t i o nCo m p u t e r Co n t r o l Co n n e c t i o n T w e e n L o u d s p e a k e r sAC M a i n s Installation Hy s i c a l InstallationG n a l P r o c e s s i n g 2X 3/8-16 X 2 LGA S E R I E S M O D E L S Y s t e m O ve r v i e wO U S T I C a L B E N E F I T S A t u r e s E C T R I C a L B E N E F I T SP p l i c a t i o n s H Y S I C a LN g i n e e r i n g D e s i g n 4a Angled Radiation PatternO w Fr e q u e n c y Pe r f o r m a n c e S a P i l o tCo m p a r i s o n t o Tr a d i t i o n a l P r o d u c t s Installation E s i g n i n g D S a S y s t e m sU D I O S I G N a L C O N N E C T I O N O M P U T E R C O N T R O L C O N N E C T I O NDaisy Chaining Computer and Audio Signals BET Ween Clusters Co b r a N e t N e t w o r k Co n n e c t i o n sEIA OFFA B L I N G U D I O / C O M P U T E R I N T E R FA C ELO U D S P E a K E R I N T E R FA C E Multiple LoudspeakersC M a i n s P o w e r C o n n e c t i o n O W E R O N / O F FEIA OFF R o u n d i n gLIF 2 Signal End / Power End 3 DSA Cluster Configurations N S TA L L AT I O N O P T I O N S N G L I N G E N C LO S U R E SO U N T I N G H E I G H T WA L L B R a C K E T I N S TA L L AT I O N7a Wall Bracket Spacing N C LO S U R E B R a C K E T I N S TA L L AT I O N N C LO S U R E I N S TA L L AT I O N9b Retainer Bolt Installation N i t i a l S e t U p Identification LEDO W E R M a N a G E M E N T OperationE D I N D I C AT O R I G N a L M O N I T O R I N G O W E R I N G U P O r m a l O p e r a t i o nI G N a L P R O C E S S I N G S E T T I N G S P e r a t i o n a l ‘ D O S ’ a n d ‘ D O N T S ’ A r r a n t y A p t e r 7 M a i n t e n a n c e a n d S e r v i c eO w t o C o n t a c t E AW A p t e r 8 a p p e n d i c e s N s p e c t i o n s a n d M a i n t e n a n c eE R I O D I C P H Y S I C a L I N S P E C T I O N S E R F O R M a N C E T E S T I N GTroubleshooting DSA250 OnlyEIA-485 I a 4 8 5 N e t w o r k A B L I N G N O T E SU p p o r t F o r C o b r a N e t E R M I N AT I O N N O T E SBack Right Side Back Front WA L L B R a C K E T 107.3 mm15.8 mm 101.5 mm 70.0 mm 4X Ø 0.38 65 mmPage R t N o . R D 0 0 8 6 D 1 4 M AY 0