EAW D S A 2 3 0, D S A 2 5 0 owner manual N C LO S U R E B R a C K E T I N S TA L L AT I O N

Page 27

5 . 5 . 8 E N C LO S U R E B R A C K E T I N S TA L L AT I O N

Insert each supplied Enclosure Bracket into its slot near each end of the enclosure, verifying the proper orientation of the enclosure. Insert a supplied 3/8-16 x 2 in Enclosure Bracket Bolt with its lock washer into each bracket bolt hole in the enclosure. Thread each bolt into the weld nut on its Enclosure Bracket and hand-tighten.

CAUTION: Make sure the brackets are installed so the enclosure orientation will be correct when the enclosure is mounted.

2X ENCLOSURE MOUNTING BRACKET P/N 0006118

2X 3/8-16 X 2 LG HEX HEAD SCREWS & LOCK WASHERS

Figure 5.5.8 Enclosure Bracket Installation

5 . 5 . 9 E N C LO S U R E I N S TA L L AT I O N

Lift the enclosure onto the structure-mounted Wall Brackets

DANGER: It is recommended that lifting the enclosure in place be performed by at least two people to prevent it from falling during its installation and causing possible equipment damage, injury, or death.

CAUTION: For DSA Clusters with two or more loudspeakers mounted one over the other, it is recommended to make all cable connections before lifting the loudspeakers onto the wall brackets. See Sections

5.2through 5.6. Once the loudspeakers are mounted, access to the connectors may be difficult.

IMPORTANT: When installing loudspeakers mounted vertically end to end, install the lower loudspeaker first.

2X WALL MOUNTING BRACKET P/N 0006119

Figure 5.5.9a Enclosure Installation

27

Image 27

Contents Page Introduction Safety Mechanical Drawings Introduction Chapter SafetyE N E R a L P R E C a U T I O N S Chapter Unpacking H i p p i n g D a m a g eE t u r n i n g P r o d u c t s t o E AW T w e e n L o u d s p e a k e r s E s c r i p t i o nU d i o S i g n a l Co n n e c t i o n Co m p u t e r Co n t r o l Co n n e c t i o nHy s i c a l Installation AC M a i n s Installation2X 3/8-16 X 2 LG G n a l P r o c e s s i n gY s t e m O ve r v i e w A S E R I E S M O D E L SO U S T I C a L B E N E F I T S E C T R I C a L B E N E F I T S A t u r e sH Y S I C a L P p l i c a t i o n s4a Angled Radiation Pattern N g i n e e r i n g D e s i g nS a P i l o t O w Fr e q u e n c y Pe r f o r m a n c eCo m p a r i s o n t o Tr a d i t i o n a l P r o d u c t s E s i g n i n g D S a S y s t e m s InstallationO M P U T E R C O N T R O L C O N N E C T I O N U D I O S I G N a L C O N N E C T I O NOFF Daisy Chaining Computer and Audio Signals BET Ween ClustersCo b r a N e t N e t w o r k Co n n e c t i o n s EIAMultiple Loudspeakers A B L I N GU D I O / C O M P U T E R I N T E R FA C E LO U D S P E a K E R I N T E R FA C EO W E R O N / O F F C M a i n s P o w e r C o n n e c t i o nR o u n d i n g EIA OFFLIF 2 Signal End / Power End 3 DSA Cluster Configurations N G L I N G E N C LO S U R E S N S TA L L AT I O N O P T I O N SWA L L B R a C K E T I N S TA L L AT I O N O U N T I N G H E I G H T7a Wall Bracket Spacing N C LO S U R E I N S TA L L AT I O N N C LO S U R E B R a C K E T I N S TA L L AT I O N9b Retainer Bolt Installation Identification LED N i t i a l S e t U pOperation O W E R M a N a G E M E N TE D I N D I C AT O R I G N a L M O N I T O R I N G O r m a l O p e r a t i o n O W E R I N G U PI G N a L P R O C E S S I N G S E T T I N G S P e r a t i o n a l ‘ D O S ’ a n d ‘ D O N T S ’ A p t e r 7 M a i n t e n a n c e a n d S e r v i c e A r r a n t yO w t o C o n t a c t E AW E R F O R M a N C E T E S T I N G A p t e r 8 a p p e n d i c e sN s p e c t i o n s a n d M a i n t e n a n c e E R I O D I C P H Y S I C a L I N S P E C T I O N SDSA250 Only TroubleshootingEIA-485 A B L I N G N O T E S I a 4 8 5 N e t w o r kE R M I N AT I O N N O T E S U p p o r t F o r C o b r a N e tBack Right Side Back Front 4X Ø 0.38 65 mm WA L L B R a C K E T107.3 mm 15.8 mm 101.5 mm 70.0 mmPage R t N o . R D 0 0 8 6 D 1 4 M AY 0