Hsu Research VTF-2 manual Volume Level, Crossover, Fine Tuning

Turning the subwoofer ON for the first time 5

On the subwoofer, check that the phase switch is at 0 degrees, the volume level knob is at the minimum, and the crossover is at 90 Hz if using the subwoofer’s crossover. Run the power cord from the wall to the subwoofer and flip the power switch to the AUTO-ON or ON position.

Step 4: Volume Level

Many people use ordinary music recordings or soundtracks for setting the subwoofer’s volume level. If you are using this method, try adjusting the subwoofer’s volume level so it matches the main speakers at the listening position. Since most people do not listen to material at very loud reference levels and the ears are less sensitive to bass at lower levels, some listeners prefer to set the bass level a little higher than the main speakers. A good approach is to set the subwoofer level to the highest level where it sounds nice and where bass and kick drums still sound tight and non-boomy. For home theater applications, most prefer to set the subwoofer level higher than the other speakers. We suggest setting it about 3 dB higher. Some proces- sors/receivers allow you to set different bass levels for different sources.

Optional: subwoofer integration will be more accurate when using test tones and a SPL meter. See Step 6 (Fine Tuning).

Step 5: Crossover

If you are using the SUBWOOFER or LFE output on your controller, you may optionally set the CROSSOVER switch to OUT. This lets the controller handle the crossover between the subwoofer and other speakers. However, if the bass sounds boomy, it may sound better with the crossover switched IN and the CROSSOVER FREQUENCY set to 90 Hz. You may skip the rest of this step.

If you are using the HIGH LEVEL speaker connections, you will be using the subwoofer’s crossover. Look up the lowest frequency your left and right speakers will output (the frequency they are“-3 dB” at) and set the crossover approximately to this point. Play program mate- rials with steady, consistent bass around this frequency such as filtered pink noise or music containing bass drums, double basses, bass guitar, etc. Turn the crossover to the left until you hear the subwoofer and L/R speakers as separate sources. Slowly turn the control back to the right until the sound of all three speakers is well integrated. When using tiny front speakers that don’t have much bass, the 90 Hz setting on the control will probably yield the best results.

Your subwoofer has a sharp 24 dB/octave crossover to remove the midbass and midrange in the subwoofer. This makes your subwoofer non-directional. Unlike many other subwoofers on the market, the 24 dB/octave slope stays steep at all available frequencies, not just the high ones.

Step 6: Fine Tuning

Now that the basic setup is complete, it’s time for optimization. Mark down the current volume and crossover settings with a soft pencil so you can go back to where you started.

Variable Tuning

If you don’t like the air shaking feeling of very deep bass, or if you often listen to extremely loud chest-thumping material that has less deep bass, Maximum Output mode is for you.

You can switch over to Maximum Output mode when the system’s volume level is low or the subwoofer is OFF. There are two steps:

1)Grip and pull out the foam port plug that is inserted in one of the port holes on the back of the subwoofer.

2)Flip the BASS EXTENTION switch on the back of the subwoofer to the MAX OUTPUT mode.

In technical language, you will get about 4 dB of extra head-room so that bass can be played louder, at the expense of some deep bass exten- sion. In other words, the subwoofer has been transformed into a louder device with less deep bass.

Switching back is simply a matter of firmly re-inserting the port plug into one of the port holes, and flipping the switch back to MAX EXTENSION mode. Make sure that the switch setting is consistent with the port setting. Using the wrong switch position at loud vol- ume levels may damage your subwoofer and void the warranty.

Setting the Phase

Depending on the absolute phase of your main speakers and amplifier, and the distances of the subwoofer and the main speakers from the listening position, the bass in the crossover region may be smoother if you reverse the phase of the subwoofer. Switch the phase switch to 180 degrees to see if the bass sounds louder in the seating position. Play program materials with steady, consistent bass in the crossover region (30 – 90 Hz). Filtered pink noise is best, but you may use music containing bass drums, double basses, bass guitar, etc.. The more bass-heavy setting is where the output of the subwoofer and the main speakers are most in phase. If the 180 degree position is louder, you will need to go back and adjust the volume level (Step 4). Otherwise, just switch the phase switch back to the original position.