Hsu Research VTF-2 manual Hookup, Moving the subwoofer

4

Moving the subwoofer

Pull the subwoofer across a carpeted floor or drag it on a throw rug. Drag it on a flat side, NOT the side with the woofer or amplifier. Once in place, remove the plastic bag.

Screw on the spiked feet. You may place the subwoofer so the amplifier panel faces out to make setup easier.

Step 3: Hookup

We will refer to receivers, integrated amplifiers, and preamps as controllers. Take a look at the back of your controller. The output connectors available determine the best method of hooking up your subwoofer.

Method A. Connecting to controllers with a SUBWOOFER or LFE output

If you have this, you should use it. All Dolby Digital, DTS, THX, and Bass Management equipped controllers have a low level SUBWOOFER or LFE output. It offers the easiest and best connection. Run a cable from it to the subwoofer’s low level SUB-IN input. A standard mono interconnect cable with RCA jacks on both ends can be purchased from electronics and audio stores. A special subwoofer cable is not needed, and neither is a Y-connector. When wiring, allow for an extra yard or two. The cables should lie flat with a little bit of slack to give you some placement flexibility.

Set your controller to enable subwoofer output. To do this, go to the SPEAKER SET-UP or BASS MANAGEMENT menu and set the SUBWOOFER to ON or YES. All the speakers should be set to SMALL if possible. This directs the deep bass from the satellites to the subwoofer, freeing them and their amplifiers from the rigorous demands of reproducing bass.

Method B. Connecting to controllers with HIGH LEVEL speaker outputs.

If your system does not have a SUBWOOFER or LFE output (for example, stereo-only inte-

grated amps or older Dolby Pro Logic receivers) you can use the HIGH LEVEL speaker outputs. The subwoofer taps the signal from the controller’s amplifier, letting the subwoofer

reproduce the bass of the left and right channels. This method is also called bass augmentation. Since the subwoofer uses its own amplifier there is no noticeable drain on your main amplifier.

You will need to run two lengths of two conductor speaker cable or zip cord. This wire is not included with your subwoofer but can be purchased at electronic or home improvement stores. Strip 1⁄2” of insulation from each end of the wire to expose the bare metal. If your speaker wire is fraying, tightly twist the metal. Unscrew the plastic hex nut on the binding post to insert the

exposed wire into the hole. Tighten the binding posts by hand.

Run the wires from your system’s amplifier to the subwoofer’s HIGH LEVEL INPUTS. For each channel, run wire from the red (+) out- puts on the amplifier to the subwoofer’s red (+) inputs, and from the black (-) outputs on the amplifier to the subwoofer’s black (-) inputs. Make sure the black amplifier outputs are “true ground.” Bridged outputs cannot be used.

Be sure to double check all connections for the correct polarity so that the positive (+) terminals go to positive (+) terminals and negative (-) terminals go to negative (-) terminals. Most wire has some marker to help you keep track of the polarity, such as ribbing, color coding, or writ- ing on one of the two strands. Tighten the binding posts by hand. If you prefer to terminate your cables, we recommend springy banana plugs for a reliable connection. They are available from electronic and audio stores.

For older Dolby Pro-Logic controllers, your center channel must be switched to NORMAL instead of WIDE, or else the bass from the center channel will not be fed into the subwoofer. For Dolby Digital controllers, go to the SPEAKER SET-UP or BASS MANAGEMENT menu on your controller and turn the subwoofer to NO or OFF and set the left and right channels to LARGE.

If you are using Method B, you may run speaker wire from the subwoofer ’s OUTPUT TO SPEAKERS connectors to your satellites. Since the speaker cables will be carrying the current for the main speakers, you will need thicker speaker wire. For runs under 10 feet long, use 18 gauge AWG wire or thicker. For 10 to 25 feet, use 16 gauge wire or thicker. For over 25 feet, use 14 gauge wire or thicker.

Method C. Connecting to controllers with PRE-OUTs.

If you do not have a SUBWOOFER or LFE output but have an extra PRE-OUT, you can use this instead of the speaker outputs. Run a stereo RCA interconnect from your PRE-OUT to the left and right inputs on the subwoofer. For Dolby Pro-Logic controllers, your center channel must be switched to NORMAL. For Dolby Digital controllers, the subwoofer must be switched to NO or OFF and the left and right channels set to LARGE.

If your system (a) has a MAIN-IN connected with a metal jumper to a PRE-OUT, or (b) you have an external amplifier, you can purchase our HSU High Pass Box for the added benefit of keeping the bass out of your speakers. Please contact your local dealer or HSU Research for details.