Yamaha DPX-830 owner manual Viewing computer images, Preparation

Page 23

◆Viewing computer images

Preparation:

•Always remove the lens cap before operating the projector.

•Turn on the power of the connected computer.

FOCUS ring

ZOOM ring

STANDBY/ON button

AUTO SYNC button

D-SUB/HDMI button

ON ( I ) button AUTO button

D-SUB button

ON

POWER

STANDBY

 

ASPECT

 

AUTO

ASPECT

HIDE

NORMAL

SQUEEZ

S. ZOOM

HDMI

COMP.

VIDEO

 

INPUT

 

D-SUB

 

S-VIDEO

 

ENTER

 

MENU

 

KEYSTN

 

MEMORY

 

1

2

3

CONT.

BRIGHT

C.TEMP

GAMMA

SHARP

IRIS

 

SETTING

 

RDP-81

1.Confirm the POWER indicator lights up red.

•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the STANDBY/ON button to turn back on the POWER indicator.

2.Press the STANDBY/ON () button on the projector or ON ( I ) button on the remote control.

•It may take about one minute for the lamp to light up.

•The lamp fails to light up on rare occasions. If this happens, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on.

3.Select an input source.

•Press the D-SUB/HDMI button on the projector or the D-SUB button on the remote control that is corresponding to the terminal in use.

–The input source is switched between D-SUB and HDMI at every press of the D-SUB/HDMI button on the projector.

•There may be a delay before an image is displayed on the screen depending on the type of the input signal.

•Images may not be projected in the correct position depending on the type of the input signal. If this happens, press the AUTO SYNC button on the projector or the AUTO button on the remote control (see page 20).

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other (see page 8).

•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle (see page 8).

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

Important

•When a 4:3 image is continuously displayed for a long time before displaying a 16:9 image, the afterimages of the black bars on each side may appear on the 16:9 image screen. Consult your dealer in this case.

•Do not display a still picture for a long time because the afterimages may persist on the screen.

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents
DPX-830 For Canadian customers Important Safety InstructionsUSA FCC Information for US customers onlyGREEN-AND-YELLOW European compliance noticeFor U.K. customers IiiTable of contents Getting started Inappropriate places for installationCables Accessory checkPower supply parts Remote control partsAttach the rear lid Inserting the batteries into the remote controlRemove the rear lid of the remote control Them correctly, inserting their side firstRear panel Controls and functionsProjector overview Control panelUsing the picture quality adjusting buttons Remote control overviewVertical directions Using the remote controlOperational range Reception angleMounting the projector on the table InstallationSetting up the screen Adjusting the projection angleOptional part Mounting the projector on the ceilingScreen size and projection distance When the aspect ratio of the screen isBasic home theater system connection ConnectionsUsing the S-VIDEO terminal Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Using the Video terminalSUB connections Hdmi or DVI connectionsFor digital connections Connecting to a computerFor analog connections To exit from the menu Plugging in the power cable With the Setup menu Trigger terminalPreparation Confirm the Power indicator lights up redProjection Viewing video imagesTo stop projecting Keystone adjustmentPress the Iris button on the remote control Iris buttonAspect button Setting the aspect ratioWith the remote control With the Initial menu Examples of the aspect ratioViewing computer images Auto / Auto Sync buttons Connecting to a notebook computerMenu overview MenuHow to set the menus Image menu Menu settingsSetup menu Initial menu Signal menu Adjusting brightness Contrast and Brightness Adjusting video imagesSelecting the gamma mode Gamma Customizing the gamma mode GammaTo activate the stored color temperature settings Selecting the color temperature Color TempCustomizing the color temperature Color Temp About color temperatureLPF Progressive filter Adjusting color Saturation and HUESharpening or softening images Sharpness Memory function Saving memory settingsTo activate the stored memory settings Press one of the Memory buttons on the remote controlTo adjust the vertical position Adjusting computer imagesSimple method to adjust the image position To adjust the horizontal positionSpare lamp Interval of lamp replacementReplacement lamp cartridge Option Replacing the lampReset of the lamp operation time MaintenanceCleaning the projector and the ventilation grilles Cleaning the lensAttaching the lens cap Attaching a lens filter and capAttaching a commercially available lens filter No image appears on the screen TroubleshootingImages are not displayed correctly Others Abnormal conditions IndicatorsNormal conditions Projector specifications SpecificationsAnalog RGB Signal specifications Composite / S-video signal specificationsComponent signal specifications Digital RGB Component Signal specificationsConnectors Dimension drawingsAll rights reserved
Top Page Image Contents