Extron electronic USFM 100 Mount the Switcher, For drywall with wood studs

Page 3

USFM 100

Cutout for

 

Marker for

Mounting

 

Holes

Base Plate

Signal Cable

Level

Pilot Hole

 

 

Access

 

 

 

 

 

 

 

 

 

 

 

 

Signal Cables

Exiting from

Cutout

Figure 2. Wall Mounting Features

c.If the cables are to be run behind the wall to the USFM 100 location, mark the cutout area on the wall large enough for signal cables (see figure 2).

d.Remove the base plate and set it aside. Cut out the marked area for cable access.

For drywall with wood studs

i.Drill ¼ inch pilot holes at the marked stud locations.

ii.Align the base plate mounting holes over the pilot holes and lightly secure with 5/16 inch lag screws and washers.

NOTE: If using toggle screws for assembly, follow the installation method (steps A-D) shown in figure 3.

A. Grasp plastic handle, collapse toggle and insert into wall.

B. Slide plastic washer down into pilot hole.

C. Cut off plastic handle close to wall.

D. Hand screw in pan head bolt until 1/8 inch gap remains.

Figure 3. Steps for Toggle Assembly Installation

iii.Verify level and position, and fully tighten down all the screws to secure the plate flush to the wall.

For drywall with steel studs

i.Drill a ½ inch (13 mm) hole through the stud at each of the locations (four recommended).

ii.Insert the supplied toggles through the studs and lightly secure the plate using the four supplied (¼-20 x 2 inch) bolts and washers.

iii.Verify level and position, and fully tighten down all the bolts to secure the plate flush to the wall.

2.Mount the Switcher

a.Place the mounting plate flat on the switcher base with the two small raised tabs on top, and the small securing tab over the front panel. Align the two mounting holes in the switcher base with the corresponding holes on the mounting plate. Secure the plate to the switcher using the two 4-40 x ¼ inch pan head screws.

b.Secure the mounting plate (and switcher) to the base plate by aligning the two small tabs on the back of the mounting plate over the corresponding tabs on the base plate (see figure 4, inset). Slide the mounting plate (and switcher) down into place. Secure it to the base plate by passing a 6-32x¼ inch screw up through the securing tab (see figure 4). Tighten down the screw.

3

Image 3
Contents Read all instructions before starting installation Important Safety InstructionsParts Qty Application InstallationRecommended Installation Tools Mount the Base PlateMount the Switcher For drywall with wood studsFor drywall with steel studs Run Cables Attach Switcher to Mounting Plate and Secure to Base PlateProceed to step Cable the SwitcherIf using a surface raceway or conduit If running cable behind the wallsHook Boom Arm Over Rail and Secure Attach the Boom Arm, Power Supply, and ProjectorUsfm 100 Dimensions Boom Arm Aligning the Projector
Related manuals
Manual 8 pages 28.88 Kb

USFM 100 specifications

The Extron Electronic USFM 100 is a cutting-edge universal signal format module designed to enhance audio-visual systems with its versatile capabilities and robust performance. This module is particularly valuable in professional AV environments, offering seamless integration with a range of signal formats for both video and audio applications.

One of the main features of the USFM 100 is its ability to support various signal formats, including HDMI, DisplayPort, and RGB. This adaptability makes it an ideal choice for multi-source setups, allowing users to connect different devices without compatibility issues. The module is equipped with advanced processing technology that ensures high-quality signal conversion, maintaining the integrity of the original content while preventing degradation.

Additionally, the USFM 100 supports high resolutions up to 4K at 60Hz, making it suitable for modern high-definition applications. This capability is crucial for venues that demand exceptional picture clarity and detail, such as conference rooms, classrooms, and professional event spaces. Furthermore, the module features an automatic EDID management function, which simplifies the process of ensuring that different devices communicate effectively and are configured correctly.

The design of the USFM 100 includes robust connectors and flexible mounting options, allowing for easy installation and integration into various AV setups. Its compact form factor makes it a space-efficient solution that can fit into standard racks or be mounted on surfaces without taking up excessive room.

In terms of audio, the USFM 100 supports multi-channel audio formats, ensuring that immersive sound experiences are delivered alongside the video content. This feature is particularly beneficial for presentations, films, or live events where audio-visual synchronization is critical.

Moreover, the module is built with reliability in mind. Extron’s commitment to quality ensures that the USFM 100 can withstand the rigors of regular use in demanding environments.

In summary, the Extron Electronic USFM 100 is a versatile and powerful tool for any AV professional. With its support for multiple signal formats, high-resolution output, automatic EDID management, and robust construction, it is designed to meet the dynamic needs of modern AV systems, making it an invaluable addition to any setup.