Brother HL-720 manual Important Wiring Information For U.K. only

Page 12

English: HL-YL User’s Guide, Preliminary (TOC)

USER’S GUIDE

IMPORTANT - Wiring Information (For U.K. only)

If the power cord supplied with this printer is not suitable for your electrical outlet, remove the plug from the mains cord and fit an appropriate three pin plug. If the replacement plug is intended to take a fuse then fit the same fuse as the original.

If a moulded plug is severed from the power cord then it should be destroyed because a plug with cut wires is dangerous if plugged into a live socket outlet. Do not leave it where a child might find it.

In the event of replacing the plug fuse, fit a fuse approved by ASTA to BS1362 with the same rating as the original fuse.

Always replace the fuse cover. Never use a plug with the cover omitted.

WARNING - THIS PRINTER MUST BE PROPERLY EARTHED.

The wires in the mains cord are coloured in accordance with the following code:

Green and yellow:

Ground

Blue:

Neutral

Brown:

Live

The colours of the wiring in the power lead of this printer may not correspond with the markings which identify the terminals in your plug. If you need to fit a different plug, proceed as follows.

Remove a length of the cord outer sheath, taking care not to damage the coloured insulation of the wires inside.

Cut each of the three wires to the appropriate length. If the construction of the plug permits, leave the green and yellow wire longer than the others so that, in the event that the cord is pulled out of the plug, the green and yellow wire will be the last to disconnect.

Remove a short section of the coloured insulation to expose the wires.

The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter “E” or by the earth symbol or coloured green or green and yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter “N” or coloured black or blue.

The wire which is coloured brown must be connected to the terminal which is marked with the letter “L” or coloured red or brown.

The outer sheath of the cord must be secured inside the plug. The coloured wires should not hang out of the plug.

x

Image 12
Contents Please read this manual thoroughly before using the printer Brother Laser PrinterShipment of the Printer Laser Printer HL-700 Series User’s Guide Trademarks Compilation and Publication NoticeDefinitions of Warnings, Cautions, and Notes To Use the Printer SafelyTable of Contents Maintenance Index-1Regulations Industry Canada Compliance Statement For Canada OnlyRadio Interference 220-240 V Model Only Declaration of Conformity For Europe Geräuschemission / Acoustic Noise Emission For Germany Only Important Wiring Information For U.K. only Finding Out How to Use the Printer About the GuidebooksAbout Your Printer Printer Overview Paper SupportFeatures Dpi Resolution and 6 ppm Printing SpeedVersatile Paper Handling USER’S Guide Environment-Friendly Economy Printing Mode Sleep Mode Power Save ModeEnhanced Memory Management Low Running CostPower Supply Operating and Storage EnvironmentEnvironment Introduction Blank Paper Specifications Paper TypePaper Size Fan the Paper Straighten the Paper Envelopes MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelopes in the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling Output Tray and Paper Support Wire Opening the Output Tray Extending the Extension Support WireLamps and Switch Ready Paper LampAlarm Lamp Data Toner LampDrum Lamp Other Control Features SwitchTest Print Mode Lamp Lit Choice FunctionChapter Options Selecting the RS-422A Apple or RS-232C IBM Serial InterfaceSetting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial InterfaceBits BitDTR only OffConnecting the Serial Interface Cable NoneOptions Memory Board Chapter Maintenance Replacing the Toner CartridgeRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 20 Turning off the Switch and UnpluggingToner Sensor Electric Terminal Gears Scanner Window 23 Cleaning the Primary Corona Wire 24 Removing the Drum Unit Assembly RE-PACKING the Printer25 Placing the Drum Unit in the Plastic Bag Alarm Indications AT a Glance Operator CallsUSER’S Guide Troubleshooting Service Calls NV-RAMPaper Jams Locating Paper Jam PositionDo Not Pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Setting Up the Printer Hardware Setting Up the Printer for WindowsQuestion RecommendationSetting Up the Printer for DOS For HL-730 series Only Paper Handling Printing Print Quality White Stripes or Faint ImagesToner scatters and stains the printed Printed pages are blurred at the center or either edge Printer Specifications Appendix aFunctions Electrical and Mechanical Parallel Interface Specifications Fig. A-1 Parallel Interface Cable Resident Fonts For HL-730 series Only Symbol SETS/CHARACTER Sets For HL-730 series Only IBM mode Epson mode HP modeHP LaserJet IIP HP LaserJet IIP, Epson FX-850, IBM Propritner XL USER’S Guide Index Sleep mode Slide switch For USA & Canada Only UL6857001 a