Speaker Placement

OWNER’S MANUAL

AIM7 DT

Single Stereo Speakers

AIM7 DT One / AIM7 DT Three

Before installing your speaker, you should consider the placement carefully, taking into account the location of electrical, plumbing and other fixtures. Contact your dealer for assistance if you are not sure of the best loca- tion in your particular room environment.

Ceiling Placement: When placing your speaker into the ceiling, it should ideally be located above the pri- mary listening area. The DT is intended to be used as a single stereo speaker in small listening environments, walk-in closets, laundry rooms, bath rooms etc. In a large area, it may be necessary to place additional speak- ers throughout the room to get the optimal effect.

MOUNTING SURFACE PREPARATION

New Construction - Unfinished Ceilings

A New Construction Bracket, SpeakerCraft part number BKT90611 (available from your dealer), may be installed prior to drywall application across joists (up to 24" on-center) where a speaker will be located. Insulation material should be in place prior to installing drywall. After the hole is cut and the drywall is installed, the speaker can then be easily installed following the instructions for mounting under “Finished Ceilings” below.

Finished Ceilings

Prior to the actual installation of the speaker, it will be necessary to run cables to the speaker location. See your dealer for more information on cable installation. After the cable has been properly installed, you are ready to mount the speaker. Following the simple steps listed below will result in a professional looking instal- lation:

1.Determine the best area to mount your speaker. This area of the ceiling should be free of obstructions such as electrical conduit, HVAC ducts, or water lines. This can best be determined by noting the placement of fixtures and gaining access to an attic or crawl space for further analysis of the location of such obstacles.

2. Find the joists nearest the desired speaker mounting location. We highly recommend using a good stud-

finder tool for this procedure. If you are lining up the speaker to some other object or molding in the room, make sure you consider the size of the baffle flange which extends beyond the mounting hole.

3.Mark the hole. A punch out template for setting the hole is provided in the box. Position the template in the desired position and pencil an outline on the ceiling.

4.	Cutting the hole. CAUTION: This is the most important part	Diagram 1

of the entire installation. If you are not certain whether any obstructions exist behind the desired mounting area, you should start by cutting a small hole in the center of your penciled mounting hole with a drywall saw, cutting at a 45º angle towards the inside of the hole. (See Diagram 1)

Cutting the small hole at this angle will make drywall repair much easier, using the piece cut out. Once you have deter- mined that there aren’t any obstructions in your desired mounting location, start cutting the finished hole at a 90º angle to the ceiling’s surface.

AIM7 DT specifications

The SpeakerCraft AIM7 DT represents a significant advancement in the realm of in-wall and in-ceiling audio solutions, catering to audiophiles and casual listeners alike. This speaker is designed to seamlessly integrate into any living space, providing an exceptional sound experience while maintaining aesthetic appeal.

One of the standout features of the AIM7 DT is its dual tweeter technology. Equipped with two pivoting tweeters, this speaker allows users to direct high-frequency sound where it is needed most, enhancing the audio experience, particularly for home theater setups. This is particularly beneficial in larger rooms or open floor plans where sound distribution can be challenging.

In addition to its dual tweeter system, the AIM7 DT utilizes a 7-inch polypropylene woofer. This material is known for its stiffness and light weight, enabling deep bass responses without distortion. The woofer is engineered to deliver rich, full-bodied sound, ensuring that all audio frequencies are reproduced accurately.

The speaker also integrates advanced design technologies such as the patented EZ mounting system. This innovative feature makes installation straightforward and hassle-free, allowing the speaker to be securely mounted in various wall or ceiling types while ensuring a clean finish. Equally impressive is the speaker's paintable grille, which offers the flexibility to match the decor of any room, virtually disappearing into the environment when not in use.

Another characteristic that sets the AIM7 DT apart is its robust construction. The speaker is built with quality components that ensure durability, making it a long-lasting addition to any audio system. Its weather-resistant design also allows for placement in more challenging environments, such as bathrooms or covered outdoor areas.

Furthermore, the AIM7 DT is compatible with a range of audio systems, making it versatile for both new installations and upgrades. Its impedance and power handling characteristics allow it to fit seamlessly into various setups, from simple stereo systems to complex home theater configurations.

In summary, the SpeakerCraft AIM7 DT combines advanced technologies, high-quality materials, and thoughtful design to deliver an exceptional audio experience. With features like dual tweeter technology, a robust woofer, and easy installation, it stands out as a top choice for anyone looking to elevate their sound without compromising on aesthetics.