Allied Telesis AT-CM2K0S manual Overview, Related Documents Verifying Package Contents, LEDs

*613-000332 Rev D*

613-000332 Rev. D

AT-CM2K0S Converteon Line Card Installation Guide

Overview

The AT-CM2K0S line card is a Gigabit copper-to-fiber media line card. You can install this line card in any Converteon Series chassis. The line card features one small form factor pluggable (SFP) transceiver slot and one copper twisted pair port. The line card is hot- swappable into and out of a Converteon chassis.

Related Documents

For details on the features and functions of a Converteon chassis, refer to the relevant documents on our web site, www.alliedtelesis.com.

Verifying Package Contents

Ensure that the following items are included in your package:

ˆOne AT-CM2K0S line card

ˆThis installation guide

If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.

AT-CM2K0S Line Card Components

An AT-CM2K0S line card has the components shown below.

Twisted Pair Port

The 10/100/1000Base-TX compliant twisted pair port has an RJ-45 connector and a maximum operating distance of 100 meters (328 feet). Category 5 (5E), 100 Ohm shielded or unshielded twisted pair cabling is required. The pinouts for this port are shown in “Twisted Pair Port Pinouts.”

LEDs

An AT-CM2K0S line card has four system LEDs, two LEDs for the SFP port, and five LEDs for the twisted pair port, as described in “LED Descriptions.”

DIP Switches

One set of DIP switches allows you to set the operating mode, as described in “DIP Switch Settings.”

Installing an AT-CM2K0S Line Card

Note

Before you install an AT-CM2K0S line card, refer to the appropriate Converteon chassis installation guide for electrical safety and emissions information.

Warning: Remove all metal jewelry, such as rings and watches, before installing or removing a line card from a powered-on chassis.

Caution: Be sure to observe all standard electrostatic (ESD) precautions, such as wearing an antistatic wrist strap, to avoid damaging the device. A line card can be damaged by static electricity

Note

You can install a Converteon line card in any Converteon chassis line card slot.

To install an AT-CM2K0S line card, perform the following procedure:

LED Descriptions

Status LEDs

The line card has four status LEDs as described in the following table. For more information about Smart MissingLink, MissingLink, and OAM, refer to the relevant management software user’s guide.

LED	State	Description
RDY	Green	The line card has passed diagnostics.
	Off	The line card has not passed diagnostics.
SML	Green	The Smart MissingLink mode is enabled.
	Off	The Smart MissingLink mode is disabled.
ML	Green	The MissingLink mode is enabled.
	Off	The MissingLink mode is disabled.
OAM	Green	The OAM mode is enabled (visible or bypass). You use the DIP
		switches to set the OAM mode, as described in “DIP Switch
		Settings.”
	Off	The OAM mode is disabled.

SFP Port LEDs

The SFP port has two LEDs, as described in the following table. For more information about Smart MissingLink, refer to the relevant management software user’s guide.

LED	State	Description
LK	Green	A link has been established on the port.
	Blinking	While in Smart MissingLink mode, a valid connection is established
	Green	on the port while a link on the other port is lost.

DIP Switches

SFP Port LEDs

SFP Port

Twisted Pair Port LEDs 10/100/1000-TX Twisted Pair Port

Line Card Status LEDs

Port Descriptions

SW1 4 3 2 1

ON

AT-
CM
AT-
CM
	2K0S
LK	AT

	SFP
	LK AT	FD
		1000M
	T
T
X
RDY
RDY	10/100/1000
	SML ML	100M
		OAM
		100M

536

536

1.Remove the AT-CM2K0S line card from its shipping package and store the package in a safe place. You must use the original package if you need to return the unit to Allied Telesis.

2.Configure the line card’s DIP switches as required. Refer to “DIP Switches” for more information.

3.Select any line card slot in the chassis where you want to install the AT-CM2K0S line card, and remove the blank slot cover if one is installed.

4.Align the back edge of the line card with the to and bottom alignment guides located inside the slot.

5.Slide the line card into the slot until the front of the card is flush with the front of the chassis.

Note

Avoid touching the line card components.

6.Secure the AT-CM2K0S line card to the chassis by using a Phillips screwdriver to tighten the captive screw on the faceplate.

Note

Always tighten the captive screw to secure the line card to the chassis.

7.Repeat this procedure to install additional AT-CM2K0S line cards.

	Off	No link has been established on the port.
AT	Blinking	TX/RX activity has been detected on the port.
	Green
	Off	There is no TX/RX activity on the port.

Twisted Pair Port LEDs

The twisted pair port has five LEDs, as described in the following table. For more information about Smart MissingLink, refer to the relevant management software user’s guide.

LED	State	Description
LK	Green	A link has been established on the port.
	Blinking	While in Smart MissingLink mode, a valid connection is established
	Green	on the port while a link on the other port is lost.
	Off	No link has been established on the port.
AT	Blinking	TX/RX activity has been detected on the port.
	Green
	Off	There is no TX/RX activity on the port.
FD	Green	The port is operating in full-duplex mode.

SFP Port

The SFP slot supports qualified SFP transceivers with a fixed operating speed of 1000 Mbps. Another AT-CM2K0S line card must be installed with an identical SFP module in a remote chassis to de-multiplex the signals. Please refer to the AT-CM2K0S Product Information/Related Products page on the www.alliedtelesis.com web site for the list of qualified SFP modules.

	Off	The port is operating in half-duplex mode.
1000M	Green	The port is operating at 1000 Mbps.
	Off	The port is not operating at 1000 Mbps.*
100M	Green	The port is operating at 100 Mbps.

1 2 3