D-Link DSL-320T Hardware Installation, Power on Modem, Factory Reset Button, Network Connections

Page 14

DSL-320T ADSL Modem User Guide

2

Hardware Installation

The DSL-320T Modem maintains two separate interfaces, an Ethernet LAN and an ADSL (WAN) interface. Place the Modem in a location where it can be connected to the various devices as well as to a power source. The Modem should not be located where it will be exposed to moisture or excessive heat. Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. As with any electrical appliance, observe common sense safety procedures.

The Modem can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.

Power on Modem

CAUTION: The Modem must be used with the power adapter included with the device.

To power on the Modem:

1.Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Modem and plug the adapter into a suitable nearby power source.

2.You should see the Power LED indicator light up and remain lit. The Status LED should light solid green and begin to blink after a few seconds.

3.If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED indicators to make sure the connection is valid. The Modem will attempt to establish the ADSL connection, if the ADSL line is connected and the Modem is properly configured this should light up after several seconds. If this is the first time installing the device, some settings may need to be changed before the Modem can establish a connection.

Factory Reset Button

The Modem may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on. Use a ballpoint or paperclip to gently push down the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the factory default IP address 192.168.1.1 and the subnet mask is 255.255.255.0, the default management Username is “admin” and the default Password is “admin.”

Network Connections

Wired network connections are provided through the ADSL port and the Ethernet port on the back of the Modem. See the Rear Panel diagram above and the illustration below for examples.

Connect ADSL Line

Use the ADSL cable included with the Modem to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Modem and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions included with the device or given to you by

4

Page 13 Page 15
Image 14
Page 13 Page 15
Contents DSL-320T Adsl Modem User Guide FCC Warning CE Mark WarningPage Table Of Contents Status Before You Start Installation OverviewSetup Wizard Packing ListInstallation Notes Information you will need from your Adsl service provider Information you will need about your DSL-320T Adsl Modem Page Modem Description and Operation Modem FeaturesIntroduction Power Front Panel DisplayRear Panel Connections Connect network cablesFactory Reset Button Hardware InstallationPower on Modem Network ConnectionsConnect Modem to Ethernet Computer to Modem ConnectionConfiguration Summary Basic Modem ConfigurationComputer IP Settings Enter Password dialog box Access the Configuration ManagerLogin to Home Web Manager First Time Log On HomeWizard DSL-320T Adsl Modem User Guide Using the Setup Wizard Choose Connection Type Using the Setup Wizard For PPPoE/PPPoA connections Using the Setup Wizard For Static IP Address connections Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard Finish and Restart DSL-320T Adsl Modem User Guide WAN Settings window PPPoE/PPPoA WANPPPoE/PPPoA PPPoA/PPPoE Parameters Description Static IP WAN Settings window- Static IP Address Static IP AddressStatic IP Parameters Description Secondary DNS Address Bridge Mode WAN Settings window- Bridge ModeDSL-320T Adsl Modem User Guide ATM Settings for WAN Connection ATM Traffic ShapingSCR Cdvt MBS ATM VC Settings ATM VC Settings in WAN Settings windowLAN Management IP windowDhcp Settings window Use the Modem for DhcpDisable the Dhcp Server Dhcp Settings window with Dhcp disabledSave Settings and Reboot System Settings windowConfiguration and Read-only Menus Advanced Modem ManagementAdsl Configuration window AdslATM VC Setting window ATM VCCTools AdminAdministrator Settings window Time Time windowRemote Log Settings window Remote LogSystem Firmware Restore Factory Default SettingsFirmware Upgrade window Diagnostic Test window TestDevice Information window StatusDevice Info Log View Log windowStatistics Traffic Statistics windowAdsl Status window Help Help windowTechnical Specifications GeneralPhysical and Environmental Control Panel Configuring IP Settings on Your ComputerConfigure Windows XP for Dhcp Click Network and Internet Connections Click Network ConnectionsClick Properties Select Obtain an IP addressConfigure Windows 2000 for Dhcp WindowsWindows 95 and Windows Configure Windows 95 and Windows 98 for DhcpConfigure Windows ME for Dhcp Windows MEConfigure Windows NT 4.0 for Dhcp Windows NT 4.0 WorkstationsIn-line low pass filter Low Pass Filters for DSLIn-Line Filter Three Port Filter Port FilterInternational Offices

DSL-320T specifications

The D-Link DSL-320T is a reliable and high-performance ADSL modem designed to provide robust Internet connectivity for home and small office environments. Known for its affordability and user-friendly features, the DSL-320T is an ideal choice for users looking to establish a stable broadband connection without complex configurations.

One of the standout features of the DSL-320T is its support for ADSL2/2+ technology, which enhances the speed and efficiency of the Internet connection. With the capability to deliver download speeds of up to 24 Mbps and upload speeds of 1 Mbps, this modem ensures smooth streaming, online gaming, and efficient file downloads. The DSL-320T also maintains backward compatibility with older ADSL standards, making it a versatile option for various Internet service providers.

The built-in Ethernet port allows for easy connection to a single computer or to a router for multiple device connectivity. This enables users to share their Internet connection seamlessly across multiple devices in their home or office. The DSL-320T also features a user-friendly web-based interface, which simplifies the setup process. With step-by-step wizards, users can quickly configure their network settings without extensive technical knowledge.

In terms of security, the DSL-320T supports various encryption standards, including WPA/WPA2 for wireless connections when used with a compatible router. It also provides firewall features to protect the network from external threats, ensuring a secure browsing experience for users.

The compact design of the DSL-320T makes it easy to integrate into any workspace. It is equipped with LED indicators that display the status of the power, DSL connection, and Ethernet link, allowing users to monitor their connection at a glance.

Additionally, the D-Link DSL-320T is known for its durability and reliability. It is built to withstand continuous operation, ensuring that users can maintain a stable Internet connection for extended periods.

Overall, the D-Link DSL-320T modem stands out as a solid choice for individuals and businesses seeking an efficient, user-friendly ADSL solution with essential features, great performance, and robust security measures to meet contemporary Internet usage demands.
Top Page Image Contents