D-Link DSL-320T manual Static IP Parameters Description

Page 31

DSL-320T ADSL Modem User Guide

To configure a Static IP connection for the WAN, follow these steps:

1.Click the Static IP Address radio button in the WAN Settings section in the middle of the window.

2.The settings under ATM VC Setting at the top of the window should not be changed unless you have been instructed to change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for your account. Leave the Virtual Circuit setting at the default (Enabled) value for now.

3.Under the Static IP heading, choose the Connection Type from the pull-down menu. This defines both the connection type and encapsulation method used for your ADSL service. The available options are Routed IP LLC and Routed IP VC-Mux.If you have not been provided specific information for the Connection Type, leave the default setting.

4.Change the IP Address, Subnet Mask, Gateway Address and (if available) Secondary DNS Address as instructed by your ISP. These are the global IP settings for the WAN interface. This is the “visible” IP address of your account. Your ISP should have provided these IP settings to you.

5.Leave the MTU value at the default setting (default = 1400) unless you have specific reasons to change this (see table below).

6.Most users will not need to change ATM settings. If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection. See the table on page 23 for a description of the parameters available for ATM traffic shaping.

7.When you are satisfied that all the WAN settings are configured correctly, click on the Apply button.

8.To save and reboot the Modem, click on the Tools directory tab and then click System. Next click the Save and Reboot button in the lower half of the System Settings window.

9.Click OK when the following “Save and restart?” dialog box opens.

10.The Modem will save the new settings and restart. Upon restarting the Modem will automatically establish the WAN connection.

The following provides additional description of the settings for Static IP Address connections:

Static IP Parameters

 

Description

 

 

 

Connection Type

This specifies the connection type and the encapsulation method used for

 

your Static IP Address connection. The options available are 1483 Routed

 

IP LLC and 1483 Routed IP VC-Mux.

IP Address

This is the permanent global IP address for your account. This is the

 

address that is visible outside your private network. Get this from your ISP.

Subnet Mask

This is the Subnet mask for the WAN interface. Get this from your ISP.

Gateway Address

This is the IP address of your ISP’s Gateway router. It provides the

 

 

 

21

Image 31
Contents DSL-320T Adsl Modem User Guide CE Mark Warning FCC WarningPage Table Of Contents Status Packing List Installation OverviewSetup Wizard Before You StartInstallation Notes Information you will need from your Adsl service provider Information you will need about your DSL-320T Adsl Modem Page Introduction Modem FeaturesModem Description and Operation Front Panel Display PowerConnect network cables Rear Panel ConnectionsNetwork Connections Hardware InstallationPower on Modem Factory Reset ButtonComputer to Modem Connection Connect Modem to EthernetComputer IP Settings Basic Modem ConfigurationConfiguration Summary Login to Home Access the Configuration ManagerEnter Password dialog box Wizard HomeWeb Manager First Time Log On DSL-320T Adsl Modem User Guide Using the Setup Wizard Choose Connection Type Using the Setup Wizard For PPPoE/PPPoA connections Using the Setup Wizard For Static IP Address connections Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard Finish and Restart DSL-320T Adsl Modem User Guide WAN WAN Settings window PPPoE/PPPoAPPPoE/PPPoA PPPoA/PPPoE Parameters Description Static IP Static IP Address WAN Settings window- Static IP AddressStatic IP Parameters Description Secondary DNS Address WAN Settings window- Bridge Mode Bridge ModeDSL-320T Adsl Modem User Guide ATM Traffic Shaping ATM Settings for WAN ConnectionSCR Cdvt MBS ATM VC Settings in WAN Settings window ATM VC SettingsManagement IP window LANUse the Modem for Dhcp Dhcp Settings windowDhcp Settings window with Dhcp disabled Disable the Dhcp ServerSystem Settings window Save Settings and RebootAdvanced Modem Management Configuration and Read-only MenusAdsl Adsl Configuration windowATM VCC ATM VC Setting windowAdministrator Settings window AdminTools Time window TimeRemote Log Remote Log Settings windowSystem Firmware Upgrade window Restore Factory Default SettingsFirmware Test Diagnostic Test windowDevice Info StatusDevice Information window View Log window LogTraffic Statistics window StatisticsAdsl Status window Help window HelpGeneral Technical SpecificationsPhysical and Environmental Configure Windows XP for Dhcp Configuring IP Settings on Your ComputerControl Panel Click Network Connections Click Network and Internet ConnectionsSelect Obtain an IP address Click PropertiesWindows Configure Windows 2000 for DhcpWindows ME Configure Windows 95 and Windows 98 for DhcpConfigure Windows ME for Dhcp Windows 95 and WindowsWindows NT 4.0 Workstations Configure Windows NT 4.0 for DhcpIn-Line Filter Low Pass Filters for DSLIn-line low pass filter Port Filter Three Port FilterInternational Offices

DSL-320T specifications

The D-Link DSL-320T is a reliable and high-performance ADSL modem designed to provide robust Internet connectivity for home and small office environments. Known for its affordability and user-friendly features, the DSL-320T is an ideal choice for users looking to establish a stable broadband connection without complex configurations.

One of the standout features of the DSL-320T is its support for ADSL2/2+ technology, which enhances the speed and efficiency of the Internet connection. With the capability to deliver download speeds of up to 24 Mbps and upload speeds of 1 Mbps, this modem ensures smooth streaming, online gaming, and efficient file downloads. The DSL-320T also maintains backward compatibility with older ADSL standards, making it a versatile option for various Internet service providers.

The built-in Ethernet port allows for easy connection to a single computer or to a router for multiple device connectivity. This enables users to share their Internet connection seamlessly across multiple devices in their home or office. The DSL-320T also features a user-friendly web-based interface, which simplifies the setup process. With step-by-step wizards, users can quickly configure their network settings without extensive technical knowledge.

In terms of security, the DSL-320T supports various encryption standards, including WPA/WPA2 for wireless connections when used with a compatible router. It also provides firewall features to protect the network from external threats, ensuring a secure browsing experience for users.

The compact design of the DSL-320T makes it easy to integrate into any workspace. It is equipped with LED indicators that display the status of the power, DSL connection, and Ethernet link, allowing users to monitor their connection at a glance.

Additionally, the D-Link DSL-320T is known for its durability and reliability. It is built to withstand continuous operation, ensuring that users can maintain a stable Internet connection for extended periods.

Overall, the D-Link DSL-320T modem stands out as a solid choice for individuals and businesses seeking an efficient, user-friendly ADSL solution with essential features, great performance, and robust security measures to meet contemporary Internet usage demands.