Motorola Powerline MU manual An Example Network Configuration for Vlan Implementation

Page 47

Powerline MU

Gateway and Modem has been selected, care must be taken to ensure that the entire network has been properly configured to support VLAN functionality.

There are two main ways that VLAN functionality can be implemented over Powerline. The first way assumes that the Modems are configured for NAT mode, and the second method assumes that the Modems are configured in Bridge mode. Figure 4 shows the test set up for both implementation examples.

Figure 27 An Example Network Configuration for VLAN Implementation.

VLAN Implementation using Modems in NAT Mode

The following steps should be followed when operating Powerline MU in VLAN pass- through mode. The Powerline MU Gateway must be enabled for VLAN by checking the “VLAN Enable” box as shown in Figure 28. Figure 28 Example of VLAN Configuration Screen in the Gateway.Next, enter the Management VID (VLAN ID) for the Powerline network.

Note: Powerline Management VID must be different from Canopy Management VID.

After the Gateway has been configured for VLAN pass-through, the LAN and WAN ports will have different functionality. Where there was no differentiation between the LAN and WAN ports in standard operating mode, in VLAN mode, the LAN port will only accept VLAN tagged packets whereas the WAN port will only accept untagged packets.

The WAN port can be used for:

Connecting a non-VLAN enabled Canopy network to the Gateway, thus allowing for a hybrid network where the Powerline network is VLAN enabled and the Canopy network is non-VLAN enabled.

Connecting to a PC or other non-VLAN IP device to the Powerline network.

Page 47 of 112

Image 47
Contents Powerline MU User Guide Trademarks, Product Names, and Service Names Table of Contents Configuring the Powerline MU Gateway List of Figures Sample Diagram a List of Tables Becoming Familiar with this User Guide About this User GuideAdmonition types Getting Additional HelpSending Feedback Send e-mail to technical-support@canopywireless.comOverview of Powerline MU Security Powerline MU FeaturesNetwork Operations Bandwidth ManagementOrdering Equipment Plug Types Powerline MU ProductsPowerline MU Canopy WirelessEthernet from SM to Gateway Connecting the Canopy Network to the GatewayGateway Location Building Electrical ConsiderationsMain Planning Owners of Electrical EquipmentInstalling Powerline MU Electrical Symbols Sample Diagram B TWO-PHASE SINGLE-PHASE Installation Two-phase installation THREE-PHASE InstallationMass Metered Mass-metered installationWiring the Panel Extender Using a Panel Extender multiple electrical panelsIndividually Metered Inductive Coupling Installation Diagram Inductive Coupler Connection, One Transformer Powerline MU Inductive Coupler 750 available Q4 Number of Splits Maximum dB loss per split Way Multiple Transformer Inductive Coupler Connection, Multiple Transformers Individually-metered installation capacitive coupling Equipment Staging Upgrading FirmwareMount the Gateway InstallationInstall Modems Connect to the Gateway Configuring the Powerline MU GatewayUser Interface Navigation tips Date and Time Configuration and MaintenanceSystem Information System Password Configuration Screen System Password ConfigurationLogs Screen LogsReboot and Reset to Defaults Screen RebootSite Info Backup and Restore SettingsAdvanced BAM ConfigurationSnmp Configuration Snmp ConfigurationPLV-GATEWAY-MIB Vlan Configuration Snmp Access ControlAn Example Network Configuration for Vlan Implementation Example of Vlan Configuration Screen in the Gateway Example Configuration of a Modem in Vlan Pass-Through Mode Modem Luid Range Configuration in the Powerline MU Gateway IP Address IP ConfigurationModem List PowerlineNEK Configuration NEK ConfigurationPSD Setting PSD SettingPowerline MU Carriers Linked to Carrier Frequency Remote NEK Modem NEK Screen Powerline ModemPage Connect to the Modem Powerline ModemConfiguring the Powerline Modem Powerline Modem Screen MAPSystem Info Screen System InfoSystem Password Screen System PasswordSystem Logs Screen System LogsReset Screen ResetBackup Screen BackupSite Info Advanced Packet Priority Advanced Packet PriorityAdvanced Bandwidth Control Advanced Bandwidth ControlAdvanced Snmp Configuration Advanced Snmp ConfigurationWhispPlvModemAdmWConfigGroup Operating Mode Modem Repeater Function Advanced Snmp Access ControlTypical Set Up for the Modem Repeater Operating Mode Use with Reeater IP Configuration IP Address with NAT Enabled Screen IP Configuration with NAT EnabledIP Address WAN 2 WANIP Address DMZ 3 DMZNetwork Encryption Key Scan DevicesPSD Setting Screen Declarations of Conformity Important Note on ModificationsNational and Regional Regulatory Notices 1 U.S. Federal Communication Commission FCC NotificationDeclaration of Conformity Gateway Page Isisis Declaration of Conformity Modem Page 0171486Nxx Model Number Description Declaration of Conformity Hybrid Adapter Issue 0171486N08 Software License Terms and Conditions Legal NoticesIsss Isssiiisis Iisssisiis Siiiiiiis Iiis Hardware Warranty in U.S Limit of Liability Additional Resources History of Changes in This Document Technical Specifications ∙ Ssss Available Now Powerline MU Gateway Issue Powerline MU Panel Extender Available Now Powerline MU Inductive Coupler 500 250 Issue 100 Appendix a International Electric Grid Plug Types Issue 102 Issue 103 Issue 104 Issue 105 Issue 106 Issue 107 Issue 108 Issue 109 Appendix B Signal Distances Issue 111 Issue 112

Powerline MU specifications

The Motorola Powerline MU is a cutting-edge device designed to enhance your home or office internet experience. With growing demands for seamless connectivity, this innovative solution leverages powerline communication technology to deliver high-speed internet access through existing electrical wiring. This means you can utilize your power outlets as network connections without the need to run extensive cabling.

One of the standout features of the Motorola Powerline MU is its impressive data transfer rates. Capable of achieving speeds up to 1000 Mbps, this device ensures that even bandwidth-intensive applications, such as streaming in 4K or online gaming, can be executed smoothly. This high-speed performance is made possible through advanced HomePlug AV2 technology, which optimizes data transfer across the powerline, significantly reducing latency and enhancing overall network efficiency.

Another remarkable characteristic of the Motorola Powerline MU is its plug-and-play simplicity. Setting up the device is straightforward; simply plug it into a wall outlet, connect it to your modem or router via Ethernet, and you’re ready to go. The user-friendly design means you don’t need to be a tech expert to get connected quickly. Additionally, with multiple Ethernet ports available, you can connect several devices simultaneously, providing versatile connectivity options for your home or office.

Security is paramount in today’s digital landscape, and the Motorola Powerline MU does not disappoint in this regard. It features 128-bit AES encryption to ensure that your data remains secure while transmitted over the powerline. This built-in security layer provides peace of mind, allowing users to connect their devices without fearing unauthorized access.

Moreover, the Motorola Powerline MU is environmentally friendly, with power-saving technologies that reduce energy consumption while in use. This aspect aligns with the growing emphasis on sustainability within the technology sector.

In conclusion, the Motorola Powerline MU stands out as an efficient and reliable solution for high-speed internet connectivity via existing electrical infrastructure. With its superior data transfer rates, intuitive setup, robust security features, and energy efficiency, it is an excellent choice for anyone looking to enhance their home or office network experience. The combination of practical design and advanced technology makes the Motorola Powerline MU a noteworthy addition to any modern digital environment.