ADTRAN SHDSL NxNTU specifications Express 6530 Menu Tree

8

61225101L1-5B

1. Unit Mode

1. NT

Main Menu

1. Unit Information

LTU

2. LT

NTU

1. Aggregate Rate (Kbps)*

2. Cross-Connect Map

1. Internal

3. LT Mode Clock Source

2. SNR Margin

0. Disabled

2. Nx64k ETC

1. Unit Options

4. Circuit ID

3. G.703 RX Clock

Alarm Threshold (dB)

2. Provisioning

2. SHDSL Options

1. -15. Threshold in dB

5. Date and Time

3. Loop Attenuation

0. Disabled

6. Reset Factory Defaults

1. Enable

Alarm Threshold (dB)

1. -127. Threshold in dB

7. Download Firmware

2. Disable

4. Outage Auto-Retrain

1. IDSN-PRA V3

8. Local Management

5. Line Probing

2. G.704 CRC-4 Multiframing

9. Change Password

3. G.703 Options

1. Inactivity Alarm Delay (Secs)

1. From DCE, TC (circuit 114)

3. G.704 Idle Pattern Ñ from 00h to FFh

0. Disabled

4. Nx64k Options

4. Network Spare Bits Insertion

2. TX Clock Source

1. Normal

1. -100. Delay in Seconds

2. From DTE, ETC (circuit 113)

3. TX Clock Polarity

5. Network Spare Bits Pattern**

2. Inverted

6. Customer Spare Bits Insertion

1. Permanent Off

5. Test Options

3. Auto

7. Customer Spare Bits Pattern**

1. Permanent On

4. RTS (Circuit 105)

2. Permanent On

8. Customer RAI Generation

5. CTS (Circuit 106)

2. DTE Driven

3. RTS Driven (V.24)

9. Customer E-Bit Generation

4. RTS Driven (C107 Emulation)

6. RTS to CTS Delay (ms)

0. -225. Delay in ms

1. Permanent Off

1. Loopback Types

7. DSR (Circuit 107)

2. Permanent On

2. In-band Loopback Options

8. DTR (Circuit 108/2)

3. Sync Mode

3. Loopback Time Out (Minutes)

0. Disabled

1. Permanent On

1. -999. Time out

9. RLSD (Circuit 109)

1. Permanent Off

2. DTE Driven

4. BERT Test Pattern Polarity

1. Normal

2. Permanent On

5. Pushbuttons (All)

3. Sync Mode

2. Inverted

6. SHDSL Port Select Pushbutton

1. Dual Sided

1. Permanent Off

1. SHDSL Loopback Type

1. PN127

7. V.35 RL (Circuit 140)

2. DTE Driven

2. G.703 Loopback Type

2. Transparent

3. Nontransparent

2. V.54

8. V.35 LL (Circuit 141)

1. Permanent Off

3. G.703 Services Loopback Type Ñ Service 1.-31.

1. In-Band Loopback Protocol

2. DTE Driven

4. Nx64k Loopback Type

Service 1. -31.

9. V.35 TI (Circuit 142)

1. Permanent Off

2. G.703 Services Pattern Detection

3. Status

2. Test Driven

1. [Local Unit] SHDSL Port

3. Nx64k In-Band Pattern Detection

2. [Local Unit] G.703 Port

4. Test

1. SHDSL Local Loopback

3. [Local Unit] G.703 Services

2. SHDSL Remote Loopback

4. [Local Unit] Nx64k Port

3. SHDSL BERT

5. [Remote Unit] SHDSL Port

1. Dual Sided

1. [Local Unit] SHDSL

4. G.703 Local Loopback

2. Customer Transparent

5. Performance History

3. Customer Nontransparent

2. [Local Unit] G.703

5. G.703 BERT

4. Network Transparent

(15-minute and 24-hour Registers)

3. [Remote Unit] SHDSL

6. G.703 Services

5. Network Nontransparent

6. Terminal Mode

7. Nx64k Local Loopback

Send In-band Pattern

8. Nx64k Remote Loopback

9. Nx64k BERT

NOTE: * Enter a new value for N from 3 to 36, where the aggregate rate (Kbps) = (Nx64) + 8

** From 00h to 1Fh for static condition of NFAS spare bits (0, 0, 0, Sa4, Sa5, Sa6, Sa7, Sa8)

Figure 5. Express 6530 Menu Tree

Software Optioning The menu tree in Figure 5 illustrates the path to every provisioning, performance monitoring, and test access point in the Express 6530 menu system.