ADTRAN DDS-DP warranty L2-5D Issue 4, June Clei Code # 5SC531PF, General, Revision History

Section 61433105L2-5D

Issue 4, June 2000

CLEI Code # 5SC531PF_ _

Series 5 Total Reach DDS-DP

Total Reach All-Rate DDS Dataport

Installation and Maintenance

CONTENTS
1.	GENERAL		1
2.	INSTALLATION		3
3.	TESTING		3
4.	REMOTE PROVISIONING AND DIAGNOSTICS		5
5.	DEPLOYMENT GUIDELINES		6
6.	MAINTENANCE		7
7. WARRANTY AND CUSTOMER SERVICE			8
Figures
Figure 1. Series 5 Total Reach DDS-DP			1
Figure 2. Total Reach DDS Circuit Diagram			2
Figure 3.		Option Switch	2
Figure 4.		DS0 Bidirectional Loopback	4
Figure 5. DDS Trouble Codes			5
Figure 6.		Remote End Initiated Loopback, Local Loop ....	6
Figure 7. Remote End Initiated Loopback, Customer
		Loop	6
Tables
Table 1.		Option Settings	2
Table 2.		LED Indication	4
Table 3.		Latching Loopback Activation Sequence	5
Table 4.		Alternating Loopback Activation Sequence	5
Table 5. Cable Type and Temperature Loss Data @
		13.3 kHz	7
Table 6. Total Reach DDS Insertion Loss
		Measurements	7
Table 7. Compliance codes			7

1. GENERAL

This practice provides installation and maintenance procedures for the ADTRAN Series 5 Total Reach® DDS-DP All-Rate DDS Dataport. Figure 1 is an illustration of the ADTRAN Series 5 Total Reach DDS-DP (P/N 1433105L5).

Revision History

This is the initial release of this document. Future revisions will be described in this subsection.

Features

•2-wire deployment

•Repeaterless operation

•Bridged tap tolerant

•Span power for remote Total Reach DDS-R termination unit

•Utilization in SLC Series 5 and Series 2000 channel banks

DDS-DP
1433105
SX	SYNC
CRC
NE	FE
QM	DSU
MAN	LBK

SW2

Figure 1. Series 5 Total Reach DDS-DP

•Loop Quality Monitor and A/B signaling options

•Bidirectional DS0 loopback capability

•Transmits Mux Out of Sync code upstream during out of service loop condition.

•Embedded Digital System 6 capabilities for remote provisioning, and performance monitoring.

Description

The ADTRAN Series 5 Total Reach DDS-DP is a functional replacement for the SLC® Series 5 OCU DP, CLEI 5SCU48, delivering data at rates up to 64 kbps using a single copper pair. Used in combination with the Total Reach DDS-R termination unit, the Series 5 Total Reach DDS-DP can accommodate extended loop lengths, eliminating the need for DDS repeaters. The Series 5 Total Reach DDS-DP span powers the Total Reach DDS-R located at the customer premises. The Total Reach DDS-R converts the 2-wire signal to the traditional 4-wire Alternate Mark Inversion (AMI) signal for presentation to the customer.

The ADTRAN Series 5 Total Reach DDS-DP occupies a single channel position in the AT&T® SLC Series 5 and Series 2000 or Series 5 compatible channel bank. It provides the interface between a DS0 timeslot of the T-carrier data stream and the 2-wire metallic loop extending to the customer premises. The

61433105L2-5D	Trademarks: Any brand names and product names included in this document are trademarks,	1
	registered trademarks, or trade names of their respective holders.